MaxLite HLRS Series User manual

Operating Instructions Hazardous Location HLRS Series
MaxLite Hazardous Location HLRS Series
• To reduce the risk of death, personal injury or property damage from fire,
electric shock, falling parts, cuts/abrasions, and other hazards read all
warnings and instructions included with and on the fixture box and all
fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires
should be performed by a qualified licensed electrician.
• DO NOT INSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and
grounded UL listed junction box.
• Make sure that the supply voltage is the same as the luminaire voltage.
• Do not install where the marked operating temperatures exceed the
ignition temperatures of the hazardous atmosphere.
• Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
• All gasket seals must be clean and undamaged.
WAR I G:
RISK OF ELECTRICALS OCK
• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical
Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
• Luminaire must be supplied by a wiring system with an equipment grounding conductor.
CAUTIO :
RISK OF INJURY
• Wear gloves and safety glasses at all times when removing luminaire from
carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTIO :
RISK OF FIRE
• Keep combustible and other materials that can
burn away from luminaire and lamp/lens.
• MIN 90°C SUPPLY CONDUCTORS.
Models:
HLRS Series
Power (45=45W, 65=65W)
Voltage (U=120-277, H=347-480)
Lens Type ([BLA K]=Clear, 110°, D=Diffused,
L=Low Bay Lens, 130°)
Color Temperature ([BLA K]=5000K, 40=4000K, 30=3000K)
Mount Type ([BLA K]=3/4” PT-Yoke Mount / U-Bracket /
Pendant, X=Ceiling, Wall 25°, Wall 90°, Stanchion 25°, Stanchion 90°)
Operating characteristic:
© Copyright 2019. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
®
Picture is for illustration purposes only.
Your model may vary.
General Safety Information
This fixture is suitable for use in the following
hazardous (classified) areas as defined by the
ational Electrical Code ( EC) and Canadian
Electrical Code (CEC):
azardous Locations
Class I, Division 2, Groups A, B, C, D
Class II, Division 1, Groups E, F, G
Class II, Division 2, Groups F, G
Class III, Division 1
Compliances Environmental Ratings
UL 1598A Suitable for hazardous
UL 1598 location.
UL 8750
UL844
Page: 1
REV: 12/19/19
Refer to the luminaire nameplate for specific classification
information, maximum ambient temperature suitability and
corresponding operating temperature (T-Code).
Rated Voltage Power Class I, Division 2 Class II, Division 1
100-240/277 Vac
347-480 Vac
45 W
65 W
40 W
60 W
-40°C (-40°F) ~ +55°C (131°F)
-40°C (-40°F) ~ +55°C (131°F)
-40°C (-40°F) ~ +52°C (126°F)
55°C (131°F)
52°C (126°F)

Installation & Operation
Electrical Connection:
1. Use the M5 Socket Tool to loosen the three M5 Socket head cap screws with spring washers of Tank Cover with torque
value 5 -m.
2. The thread of entry hole of Tank is 3/4” NPT. Attach the Tank to suitable conduit.
3. Insert the wire from outside through the conduit and the entry hole of Tank, and then connect to Terminal Block.
4. Introduce the wires of branch circuit as following:
Black-wire connects to Line
White-wire connects to eutral
Green-wire connects to Ground
1. Re-attach the Tank Cover and tighten it using the three M5 socket head screws with spring washers with a
torque value 5 -m.
2. Check the tightness of the conduit and Tank Cover.
General Wiring Diagram
CAUTIO : Turn off electrical power at fuse
or circuit breaker box before wiring fixture to
the power supply.
Connecting panels to AC source supply:
All units must be individually connected to
the AC supply.
Black = Line
White = Neutral
Green = Ground
© Copyright 2019. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 2
REV: 12/19/19
Φ262mm (10.3in)Φ262mm (10.3in)
155mm
(6.1in)
279mm
(11in)
Operating Instructions Hazardous Location HLRS Series
MaxLite Hazardous Location HLRS Series
®
M5 Socket Tool

© Copyright 2019. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 3
REV: 12/19/19
Mount Accessories
Pendant:
1. Fix the tank cover on the NPT ¾” threaded pipe
then tighten the M4 fastening screws.
2. Connect electrical components.
3. Use the three M5 socket head screws to fix the
luminaire with a torque value of 5 -m.
U-Bracket:
1. Use the four M8 expansion bolts to fix the bracket to the wall.
2. Connect electrical components.
3. Use the three M5 socket head screws to fix the luminaire with a
torque value of 5 -m; adjust the angle of the lamp and use the
M4 screws to fix the fixture in place.
step1
step2
Set screw
M4
Socket head cap screws
M5
step3
step1
step2
Socket head cap screws
M5
Screws
M4
(Gasket+Washers induded) M8
Expansion bolts
step3
Operating Instructions Hazardous Location HLRS Series
MaxLite Hazardous Location HLRS Series
®

© Copyright 2019. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 4
REV: 12/19/19
Mount Accessories
Ceiling:
1. Use the four M8 expansion bolts to fix the bracket to the ceiling.
2. Use the six M4 hexagon socket screws with a torque value
of 3 -m in order to fix the driver cavity cover to the bracket.
3. Lights should be hung on the driver cavity cover; connect wires
accordingly.
4. Use the three M5 socket head screws with torque value of
5 -m to the fixture.
Stanchion 25° / Stanchion 90°:
1. Screw the bracket into the pole and tighten the M5 fastening
screws.
2. Use the six M4 hexagon socket screws to fix the tank cover
to the bracket with a torque value of 3 -m.
3. Connect electrical components.
4. Use the three M5 socket head screws to fix the luminaire with
a torque value of 5 -m.
M4 Socket head cap screws
(Gasket+Washers induded) M8
Expansion bolts
step1
step2
M4
step3
step4
M5
Socket head cap screws
Screws
M5
step1
step2
step3 step4
M5
Socket head cap screws
M4
Socket head cap screws
Operating Instructions Hazardous Location HLRS Series
MaxLite Hazardous Location HLRS Series
®

© Copyright 2019. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 5
REV: 12/19/19
Mount Accessories
Wall 25° / Wall 90°:
1. Use the four M8 expansion bolts to fix the bracket to the wall.
2. Use the six M4 hexagon socket screws to fix the bracket with
a torque value of 3 -m.
3. Use the six M4 hexagon socket screws to fix the driver cavity
cover to the bracket with a torque value of 3 -m.
4. Connect electrical components.
5. Use the three M5 socket head screws to fix the luminaire
with a torque value of 5 -m.
(Gasket+Washers induded) M8
Expansion bolts
step1
step2
step3
step5
step4
M4
Socket head cap screws
Standard: Optional:
Wall 90°Stanchion 25° Stanchion 90° Wall 25°
Ceiling mount
Pendent U bracket
Operating Instructions Hazardous Location HLRS Series
MaxLite Hazardous Location HLRS Series
®

© Copyright 2019. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Servicing
• To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing
maintenance.
• Perform visual, electrical, and mechanical inspections on a regular basis. The environment and frequency
of use should determine this. owever, it is recommended that checks be made at least once a year.
Frequency of use and environment should determine this.
• The external glass should be cleaned periodically to ensure continued luminaire performance. Clean the
glass with a clean, damp, non-abrasive, lint-free cloth. If this is not sufficient, use a mild soap or a liquid
cleaner. Do not use an abrasive, strong alkaline or acid cleaner as damage may occur.
• Inspect the cooling fins on the luminaire to ensure that they are free of any contamination
(i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
• Mechanically check that all parts are properly assembled.
• Electrically check to make sure that all connections are clean and tight.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and (2)this device must accept any interference
received, including interference that may cause undesired operation
Page: 6
REV: 12/19/19
Operating Instructions Hazardous Location HLRS Series
MaxLite Hazardous Location HLRS Series
®

© Copyright 2019. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 7
REV: 12/19/19
MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the earlier of the actual installation date
or 90 days after the original date of purchase from a MaxLite authorized distributor/dealer (the “Warranty Period”), as
follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship,
MaxLite will, at its option, repair it, replace it with the same or like Product.
Please refer to Maxlite’s website (at http://maxlite.com/resources/warranties) for the complete coverage details as well
as the terms and conditions of our warranty. Please note that it is NOT a requirement to register your warranty in order
to initiate a warranty claim unless a Ten Year warranty has been purchased separately, or when applicable and/or
purchased separately, your warranty contains a replacement labor allowance.
Limitation of Liability
T IS WARRANTY IS EXCLUSIVE, AND IS T E SOLE REMEDY FOR ANY AND ALL CLAIMS, W ET ER IN
CONTRACT, IN TORT OR OT ERWISE ARISING FROM T E FAILURE OF PRODUCT AND IS IN LIEU OF ALL
OT ER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF MERC ANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, W IC WARRANTIES ARE EREBY EXPRESSLY DISCLAIMED TO
T E EXTENT PERMITTED BY LAW AND, IN ANY EVENT, S ALL BE LIMITED TO T E WARRANTY PERIOD
SPECIFIED ABOVE. T E LIABILITY OF MAXLITE S ALL BE LIMITED TO T E TERMS OF T E EXPRESS
WARRANTY SET FORT EREIN. IN NO EVENT WILL MAXLITE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES INCLUDING, WIT OUT LIMITATION, DAMAGES RESULTING FROM LOSS OF
USE, PROFITS, BUSINESS OR GOODWILL, LABOR COSTS, REMOVAL OR INSTALLATION COSTS, W ET ER
OR NOT MAXLITE AS BEEN ADVISED OF T E POSSIBILITY T EREOF. UNDER NO CIRCUMSTANCES S ALL
MAXLITE’S ENTIRE LIABILITY FOR A DEFECTIVE PRODUCT EXCEED T E PURC ASE PRICE OF T AT
PRODUCT (EXCLUDING LABOR WARRANTY COVERAGE W ERE SPECIFCALLY OFFERED BY MAXLITE).
WARRANTY SERVICES PROVIDED UNDER T ESE TERMS AND CONDITIONS DONOT ENSURE T E
UNINTERRUPTED OPERATION OF PRODUCTS; MAXLITE S ALL NOT BE LIABLE FOR DAMAGES CAUSED
BY ANY DELAYS INVOLVING WARRANTY SERVICE.
This Warranty gives you specific legal rights and you may also have other rights that may vary from state to state.
Because some states or jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental
damages, such limitation may not apply to you.
Warranty Information
Operating Instructions Hazardous Location HLRS Series
MaxLite Hazardous Location HLRS Series
®