Maxon PM200 User manual

User Manual PM200
Page 1
English
Table of Contents
.................................................................................................................1Table of Contents
.........................................................................................................................3Specification
..............................................................................................3About Your PM200 Radio
................................................................................................................4Safety Information
..........................................................................................................5Unpacking Information
................................................................................................6PM200 Features & Description
......................................................................................................6Product Description
...........................................................................................................7Front and Rear panels
........................................................................................................7Front panel layout
.........................................................................................................7Rear panel layout
...................................................................................................8Front and Rear descriptions
..........................................................................................................................9LCD Display
..........................................................................................................10Basic Radio 0peration
...............................................................................................10On/Off Volume Control
...................................................................................................................10Channels
............................................................................................................10Output Power
.....................................................................................................10Beep On/Off Mode
...........................................................................................................10Public Address
..................................................................10Internal Speaker and External Audio Switch
.......................................................................................................10Microphone Hook
.........................................................................................................11Squelch Options
.........................................................................................................................11CTCSS
............................................................................................................................11DCS
................................................................................11Squelch Defeat (Monitor) operation
..........................................................................................................12Muting Options
.................................................................................................................12PTT Timer
..................................................................................................................12TX Inhibit
...................................................................................................................12TX Delay
................................................................................................12Busy Channel Lockout
...............................................................................................................12Marked Idle
..............................................................................................................12PTT Lockout
..............................................................................................................13Display Logo
...........................................................................................................13Power up Alert
...................................................................................................................13Scanning
..............................................................................................................13Normal Scan
..............................................................................................................13Priority Scan
Priority Look Back Scan...............................................................................................13
.....................................................................................14Transmitting During Scanning
..................................................................................................14Scan Channel Delete
................................................................................................14Group Scan Edit Mode
...........................................................................................14Priority Scan Channel Edit
...............................................................................................15Basic programmable features
............................................................................................................15Function Keys
.................................................................................................15Up/Down Keys (▼▲)
......................................................................................15Programmable Function Keys
.................................................................................................................15Power key
...................................................................................................................15Light Key
...............................................................................................................16Monitor Key
...................................................................................................................16Lock Key
...................................................................................................................16Scan Key
.....................................................................................................16Public address Key
.........................................................................................................16Open/Close Key
.................................................................................................................16Selcall Key
....................................................................................................................16SMS Key

User Manual PM200
Page 2
1200/2400 bps Key ....................................................................................................16
DTMF Key..................................................................................................................16
Group Key .................................................................................................................16
Emergency Key..........................................................................................................17
Status and Error Messages................................................................................................... 18
Service Information.............................................................................................................19

User Manual PM200
Page 3
English
Specification
About Your PM200 Radio
Maxon's PM200 Series radio features 208 channels. Operation and functions of these radios are
outlined in this manual.
We urge you to thoroughly read this manual before operating the radio
The application of some of the functions described in this manual is determined by the system
you use. Your Maxon Dealer will program your radio so that you have the greatest number of
functions possible relative to your needs.
Performance Specifications R&TTE Directive 1999/5/EC
ETSI EN 300 086-1/-2
EMC Directive 89/336/EEC
ETSI EN 301 489-1/-5
LV Directive 73/23/EEC EN 60950-1
72/245 EC as assembled by 2004/104/EC
Frequency coverage (UHF) 440.000 – 480.000MHz
(VHF) 148.000 – 174.000MHz
Channel Spacing 12.5 kHz, / 25 kHz
(12.5 / 25 kHz switchable by CPU control)
RF Output Power PM200 2W - 25W nominal (+/-20%)
RF Output Power PM250 5W - 45W nominal (+/-20%)
Modulation Type F3E/G3E
Audio Power 4W (Internal 16speaker)
Intermediate Frequencies 45.1MHz First I.F.
455 kHz Second I.F.
Number of Channels 208 Channels
Frequency Source PLL Synthesiser
Frequency Stability +/- 2.5ppm
Power Supply 13.8Vdc nominal
10.8Vdc minimum (extreme)
15.6Vdc maximum (extreme)
Specification
Current Consumption OFF <10µA
Standby (muted) <140mA
Unmuted with 25% AF power <350mA
Unmuted with 50% AF power <450mA
Unmuted with 100% AF power <1000mA
Transmit @ 2W RF output <2.0A
Transmit @ 25W RF output <7.0A

User Manual PM200
Page 4
English
Safety Information
1. WARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard
or result in an electric shock.
2. NEVER operate the radio transmitter without a suitable artificial load or antenna
connected.
3. NEVER connect the transceiver to a power source of more than 16V DC such as a 24V
battery.
4. NEVER cut the DC power cable between the DC Plug and fuse holder. If an incorrect
connection is made after cutting, the transceiver may be damaged.
5. NEVER place the transceiver where normal operation of the vehicle may be hindered or
where it could cause bodily injury.
6. NEVER expose the transceiver to rain, snow or any liquids.
7. NEVER modify a radio or accessory except as instructed in the service manual,
engineering bulletins or formal communication as this may invalidate any warranty,
guarantee or type approval.
8. USE the supplied microphone only. Other microphones have different pin assignments
and may damage the transceiver. (ACC-700, optional DTMF MIC. ACC-703)
9. DO NOT use or place the transceiver in areas with temperatures below -30ºC or above
+60°C in areas subject to direct sunlight, such as the dashboard.
10. AVOID operating the transceiver without running the vehicle’s engine. The vehicle’s
battery will quickly run out if the transceiver transmits while the vehicle’s engine is OFF.
11. AVOID placing the transceiver in excessively dusty environments.
12. AVOID the use of chemical agents such as benzene or alcohol when cleaning, as they
damage the transceiver surfaces.
13. BE CAREFUL! The transceiver will become hot when operating continuously for long
periods.
14. DO NOT operate this equipment in environments containing explosive materials or
vapors.
Warnings

User Manual PM200
Page 5
English
Unpacking Information
Remove and carefully inspect the contents of your package(s) for the following items:
1. PM200 Transceiver
2. Microphone
3. Installation kit
4. User Manual
* If any items are missing, please contact your Dealer
PM200 + Microphone
Power lead with 10 amp fuse
Installation kit
1. 1 x Fixing bracket
1
Unpacking information
2. 1 x Microphone bracket
3. 2 x Thumb wheel screws
4. 2 x M3 x 6mm Mic bracket Screw
5. 2 x M5 x 11mm fixing screws
3
6. 2 x M3 Washers
7. 2 x M5 Washers
8. 2 x M3 Spring Washers
2
4
5
9. 2 x M5 Spring Washers
10. 4 x Rubber feet
6
7
8
9

User Manual PM200
Page 6
English
PM200 Features & Description
2W or 25W Programmable output power
208 Programmable Channels
D-SUB 15Pin Data Connector
Programmable 12.5 /25 KHz Channel Spacing
Channel Scan
Priority Channel Scan
Look Back Channel
Scan List Edit
Priority Channel Edit
CTCSS/DCS/DTMF tone signalling
Busy Channel Lock-out
Mark Idle
Time out timer
Public Address
SELCALL
Stun and Revive
Covert Mode
ANI
SELCALL Messaging
Acknowledge
Key Lock
Start up Definable Logo
Auto Mute
Back Light Display
SMS
DTMF
HOOK Switch
Product Description
The PM200/250 is a fully featured mobile radio that has been developed for the European
market. The PM200/250 is a DTMF, Selcall and SMS mobile radio with a 208-channel capability.
The radio is programmable for output power, channel spacing, and a range of other features.
The PM200 mobile radios are packed full of sophisticated user and system features which allow
the radios to be tailored to meet the requirements of most radio networks today.
All the features described are made available thanks to the latest reliable, but functionally rich,
software that controls each PM200 mobile. This means that all features described are available
without the need to fit expensive and time consuming option boards.
Most of the features or options described are activated in the radio as programmable parameters;
please contact your dealer for full details on these options.
The PM200 is a DTMF, SECALL and SMS mobile radio with 208-channel capability. The radio is
programmable for output power, channel spacing, and a range of features. The three buttons
located on the bottom left-hand side of the radio under the LCD, are described as programmable.
These three buttons (P1, P2, and P3) have a short and long press and can be used for various
pre- programmed features, Monitor, Power H/L, Scan, DTMF, Key lock, Selcall, Scan, Public
Address, Open Close, 1200/2400, SMS and Light. The range does conform to R+TTE Directive.
The unit meets the R+TTE Directive ETS 300.086 2001.
Feature List

User Manual PM200
Page 7
English
Front and Rear panels
Front panel layout
1.) RJ45 Microphone Socket
2.) On/Off Volume Control
3.) Alpha Numeric LCD
4.) (P1-P3) Programmable Keys
5.) Status LED
6.) Emergency Key (Orange)
7.) Up/Down Channel/Menu Keys
8.) Internal Speaker
Rear panel layout
Front and Rear Panels
9.) BNC Antenna Connector
10.) 15 way D-type (programming/cloning)
11.) GPS antenna port (Optional)
12.) DC power lead
13.) Accessory Socket

User Manual PM200
Page 8
Front and Rear descriptions
1. Microphone socket
Connect the supplied microphone or optional DTMF/Heavy Duty microphone.
NEVER connect non-specified microphones the pin assignments may be different and
the transceiver may be damaged.
2. Volume control switch
To turn the radio ON and OFF, rotate the knob clockwise ON and anticlockwise to turn OFF.
Rotate the knob to adjust the audio output level up and down.
3. LCD Display
Displays a variety of information such as an operating channel number, SELCALL Number,
DTMF number and Volume level, etc. NOTE: The above functions depend on programming.
4. Dealer programmable keys (P1) to (P3)
Desired functions can be programmed independently by your dealer.
5. LED Indicator
Indicates radio condition from LED colour (see status and indicator and alert tones in
section 6.)
6. Emergency key
Transmits emergency call
7. Up/Down keys
Push to select the operating channel.
8. Internal Speaker
Note: Internal and external speakers can be switched by holding in the P1 and P3 buttons
during radio switch on. The display will indicate which state the radio is in.
Rear View description
9. BNC Antenna connector
Connects to an antenna. Contact your dealer about antenna selection and placement.
10. D-SUB 15Pin Connector
Connect DB-9 and DB-15 connector of PK-PM200/250-01 to the PC and radio for
programming.
11. External Speaker Jack
Connect an 8 - 16external speaker, if desired
12. GPS Antenna Tube
Space for a GPS antenna and internal connectors have been included for customer
applications.
13. DC Power Receptacle
Connects to a 12V Dc battery 13.8Vdc nominal 10.8Vdc minimum (extreme) 15.6Vdc
maximum (extreme).
English
Basic Radio Descriptions

User Manual PM200
Page 9
English
LCD Display

PL
23
4
567890
1
1.) Signal strength indicator: Indicates relative signal strength level.
2.) TX Indicator: Appears while transmitting.
3.) Scan Indicator: Appears at the scan Channel.
4.) P Scan Indicator: Appears at the Priority scan Channel.
5.) Key Lock Indicator: Appears when the key lock function is on.
6.) Speaker Indicator: Appears when in the monitor mode.
7.) Low Power Indicator: Appears when low output power is selected.
8.) Selcall Detect Indicator: Appears when the selcall code is received.
9.) Currently not used.
10.) Currently not used.
The LCD can display Alpha numeric characters and can be scrolled using the programmerable
(P1) – (P3) keys. Short message service Text can be sent and displayed by the PM200. Selcall
numeric codes stun and revive and error messages can also be displayed.
LCD Display