Maytag Amana PMH Series Guide

Service and Troubleshooting



©2014-2018, 2020 Goodman Company, L.P.
This manual is to be used by qualied, professionally
trained HVAC technicians only. Goodman does not assume
any responsibility for property damage or personal injury
due to improper service procedures or services performed
by an unqualied person.
RS4200005r14
June 2020
TABLE OF CONTENTS
IMPORTANT INFORMATION . . . . . . . . . . . . . . . . . . . . 2
PRODUCT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . 3
SYSTEM OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 12
SCHEDULED MAINTENANCE . . . . . . . . . . . . . . . . . . . . 27
SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
CHECKING VOLTAGE .......................39
CHECKING THERMOSTAT AND WIRING .......39
HEATER ASSEMBLY ........................40
DRAIN PAN VALVE (HEAT PUMP MODELS ONLY)
..........................................41
CAPACITOR CHECK ........................41
CHECKING FAN AND MOTOR BLOWER WINDINGS
..........................................42
COMPRESSOR WINDINGS ..................43
OVERLOAD................................44
CHECKING COMPRESSOR EFFICIENCY ......44
FILTER DRIER REPLACEMENT...............44
REVERSING VALVE.........................45
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Pride and workmanship go into every product to provide
our customers with quality products. It is possible, however,
that during its lifetime a product may require service.
Products should be serviced only by a qualied service
technician who is familiar with the safety procedures
required in the repair and who is equipped with the proper
tools, parts, testing instruments and the appropriate service
manual. 




















Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
0140M00517-A
® is a registered trademark of Maytag Corporation or its related companies and is used under license to
Goodman Company, L.P.. Houston TX, USA.. All rights reserved.

IMPORTANT INFORMATION
2











OUTSIDE THE U.S., .
(Not a technical assistance line for dealers.) Your telephone company will bill you for the call.

While these items will not cover every concievable
situation, they should serve as a usefull guide.
Pride and workmanship go into every product to provide
our customers with quality products. It is possible, how-
ever, that during its lifetime a product may require service.
Products should be serviced only by a qualied service
technician who is familiar with the safety procedures
required in the repair and who is equipped with the proper
tools, parts, testing instruments and the appropriate service
manual. REVIEW ALL SERVICE INFORMATION IN THE
APPROPRIATE SERVICE MANUAL BEFORE
BEGINNING REPAIRS.

PRODUCT IDENTIFICATION
3

1,2,3 4,5 6 7 8,9 14,15
PTC
PTH
HEH
32C High-Efficiency R32 Cooler PTAC
A
C
DDoor
F
L
H
P
Q
R
VPo
Xplaceholder
He
00 N
15
25
*
G
PTC123*50AXXX PTC073*35CRXX
H
R-410A
High- -410A
High-Efficiency R-32
PTC123*50CXXX PTC073*25CQRW
AXXX AA
10,11,12,13
PTC 07 3 G 35
HEC High-Efficiency Cooler PTAC
J
DRY
Model/Revision Description
PT*********** AA Redesign unit with 2 fan motors and R410A refrigerant
PT*********** AC 2 Speed Condenser Fan Motor
PT*********** BA M70 Control Board
PT*********** EA
Release of units with low displacement compressor 7
and 12 K HP PTAC models. Only for standard models and high efficiency models
PT*********** GA Transition from Fayetteville to Houston built product
Package Terminal Air Conditioner

SPECIFICATIONS
4
Model ¹, 6, 8, 9PMC073G** PMC093G** PMC123G** PMC153G**
230 / 208 230 / 208 230 / 208 230 / 208
6,800 / 6,700 9,000 / 8,700 11,800 / 11,700 14,500 / 14,400
3.2 / 3.2 4.3 / 4.3 6.0 / 6.0 7.1 /7.1
565 / 550 775 / 760 1,070 / 1,060 1,460 / 1,450
12.0 / 12.1 11.6 /11.4 11.0 / 11.0 9.9 / 9.9
25-35 25-35 25-35 25-35
5555
Voltage ¹, ³
Amps10
Watts10
Capacity (BTU/h)
EER
Kit Fresh Air, CFM
Kit Dehumidification (Oz/Hr)
Model ¹, 6, 8, 9PMH073G** PMH093G** PMH123G** PMH153G**
230 / 208 230 / 208 230 / 208 230 / 208
Capacity (BTU/h) 6,900 / 6,700 8,700 / 8,700 11,400 / 11,200 14,700 / 14,700
3.4 / 3.4 4.2 / 4.2 6.2 / 6.2 7.4 / 7.4
575 / 555 670 / 655 1055 / 1015 1,530 / 1,530
EER 11.9 / 12.0 11.7 / 11.8 10.8 / 11.0 9.6 / 9.6
Kit Fresh Air, CFM 25-35 25-35 25-35 25-35
Kit Dehumidification (Oz/Hr)
5555
Voltage ¹, ³
Amps10
Watts10
Model ¹, 6, 8, 9PMH074G** PMH094G** PMH124G**
265 265 265
Capacity (BTU/h) 7,700 9,000 12,000
3.2 4.3 5.1
655 795 1150
EER 11.7 11.3 10.4
Kit Fresh Air, CFM 25-35 25-35 25-35
Kit Dehumidification (Oz/Hr)
555
* Actual vent CFM performance will vary due to application and installation conditions.
Voltage ¹, ³
Watts10
Amps10
Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
³ Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
5Heating capacity and efficiency based on unit operation without condensate pump.
6Specify two-digit heater kW size to complete model number.
7R-410A refrigerant used in all systems. R-134A used in Kit Fresh Air.
8All units meet or exceed ASHRAE 90.1 standards.
9 All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
10 Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
4Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay fuses
(included and factory-installed on all Amana® brand 265-volt chassis). See heater perform
 - Energy E󰀩ciency Ratio per The Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) Test Procedures and Canadian
Standards Association (CSA) Test Procedures.
 - Coe󰀩cient of Performance per AHRI Test Procedures


SPECIFICATIONS
5

PTC PTC PTC PTC PTC PTC PTC PTC PTC
073G** 074G** 092G***BA* 093G*** 094G*** 123G** 124G*** 153G*** 154G***
230/208 265 115 230 / 208 265 230/208 265 230 / 208 265
7,000 / 7,000 7,000 9,000 9,200 / 9,000 9,100 11,900 /11,700 12,200 14,800 / 14,500 14,800
3.1 / 3.1 2.7 8.3 4.1 / 4.1 3.6 6.0 / 6.0 4.8 7.0 / 7.0 6.1
580 / 560 585 795 790 / 765 805 1,080 / 1,060 1,170 1,480 / 1,450 1,480
12.0 / 12.5 11.9 11.3 11.6 / 11.7 11.3 11.0 / 11.0 10.4 10.0 / 10.0 10.0
Unit without Electric Heater
3.7 3.2 8.3 4.9 4.4 7.3 5.8 8.5 7.4
High 330 340 290 290 290 340 340 340 340
Low 245 245 264 264 264 245 245 314 314
High 360 370 310 310 310 370 370 360 360
Low 270 270 282 282 282 270 20 332 332
40* 65* 65** 65** 65** 40* 40** 65** 65**
1.7 1.7 2.2 2.2 2.2 1.7 1.7 4.4 4.4
106 103 102 102 102 108 108 113 113
115 115 117 117 117 125 125 130 130
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Ventilated Air, CFM (Fan Only)**
Dehumidification (Pints/Hr.)
Net Weight (lbs.)
Model 1, 7, 9, 10
Voltage ¹, ³
Amps11
Watts11
Min. Circuit Amps 2, 5, 11
Ship Weight (lbs.)
Capacity (BTU/h)
EER
* Information in this manual applies only to the BA revision of 0902G*** model.
** Actual vent CFM performance will vary due to application and installation conditions.
Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
3Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
4Minimum voltage on 115-volt models is 104 volts; maximum is 127 volts.
6Heating capacity and efficiency based on unit operation without condensate pump.
7Specify two-digit heater kW size to complete model number.
8R-410A refrigerant used in all systems.
9All units meet or exceed ASHRAE 90.1 standards.
10 All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
11 Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
5Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay fuses
(included and factory-installed on all Amana® brand 265-volt chassis). See heater perform
 - Energy E󰀩ciency Ratio per The Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) Test Procedures and Canadian
Standards Association (CSA) Test Procedures.
 - Coe󰀩cient of Performance per AHRI Test Procedures

SPECIFICATIONS
6
PTC PTC PTC
073G**DA 093G***DA 123G**DA
230/208 230 / 208 230/208
7000/7000 9,200 / 9,000 11500/11400
3.1/3.1 4.1 / 4.1 5.1/5.1
580/560 790/765 1045/1015
12/12.5 11.6 / 11.7 11.0/11.2
Unit without Electric Heater
3.7 5.0 6.2
High 330 290 340
Low 245 264 245
High 360 310 370
Low 270 282 270
40* 65** 40*
1.7 2.2 1.7
106 108 110
115 119 126
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Ventilated Air, CFM (Fan Only)**
Dehumidification (Pints/Hr.)
Net Weight (lbs.)
Model 1, 7, 9, 10
Voltage ¹, ³
Amps11
Watts11
Min. Circuit Amps 2, 5, 11
Ship Weight (lbs.)
Capacity (BTU/h)
EER
* Information in this manual applies only to the BA revision of 0902G*** model.
** Actual vent CFM performance will vary due to application and installation conditions.
Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
3Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
4Minimum voltage on 115-volt models is 104 volts; maximum is 127 volts.
6Heating capacity and efficiency based on unit operation without condensate pump.
7Specify two-digit heater kW size to complete model number.
8R-410A refrigerant used in all systems.
9All units meet or exceed ASHRAE 90.1 standards.
10 All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
11 Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
5Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay fuses
(included and factory-installed on all Amana® brand 265-volt chassis). See heater perform
 - Energy E󰀩ciency Ratio per The Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) Test Procedures and Canadian
Standards Association (CSA) Test Procedures.
 - Coe󰀩cient of Performance per AHRI Test Procedures


SPECIFICATIONS
7
HEC HEC HEC
073H** 093H*** 123H**
230/208 230 / 208 230/208
7,000/7,000 9,200 / 9,000 11,900 / 11,700
3.7 / 3.7 4.7 / 4.7 6.6 / 6.6
555 / 530 765 / 740 1,050 / 1,040
12.6 /13.1 12.0 / 12.1 11.3 / 11.2
Unit without Electric Heater
4.3 5.6 7.9
High 330 290 340
Low 245 264 245
High 360 310 370
Low 270 282 270
40* 65** 40*
1.7 2.2 1.7
106 108 110
115 119 126
Model 1, 7, 9, 10
Voltage ¹, ³
Amps11
Watts11
Min. Circuit Amps 2, 5, 11
Ship Weight (lbs.)
Capacity (BTU/h)
EER
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Ventilated Air, CFM (Fan Only)**
Dehumidification (Pints/Hr.)
Net Weight (lbs.)
* Information in this manual applies only to the BA revision of 0902G*** model.
** Actual vent CFM performance will vary due to application and installation conditions.
Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
3Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
4Minimum voltage on 115-volt models is 104 volts; maximum is 127 volts.
6Heating capacity and efficiency based on unit operation without condensate pump.
7Specify two-digit heater kW size to complete model number.
8R-410A refrigerant used in all systems.
9All units meet or exceed ASHRAE 90.1 standards.
10 All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
11 Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
5Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay fuses
(included and factory-installed on all Amana® brand 265-volt chassis). See heater perform
 - Energy E󰀩ciency Ratio per The Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) Test Procedures and Canadian
Standards Association (CSA) Test Procedures.
 - Coe󰀩cient of Performance per AHRI Test Procedures


SPECIFICATIONS
8

Model ¹, 6, 8, 9PTH
073G**
PTH
093G**
PTH
123G**
PTH
153G**
PTH
074G**
PTH
094G**
PTH
124G**
PTH
154G**
230 / 208 230 / 208 230/208 230 / 208 265 265 265 265
7,100 / 7,000 9,000 / 9,000 11,600 / 11,400 14,200 / 14,400 7,600 9,100 12,000 14,600
3.3 / 3.3 4.1 / 4.1 6.1 / 6.1 7.0 / 7.0 33.6 4.9 6.1
560 / 535 705 / 685 970 / 960 1,430 / 1,410 645 755 1090 1,505
12.0 / 12.4 11.9 / 12.0 11.0 / 11.1 9.9 / 9.9 11.7 12 11 9.7
Unit without Electric Heater
4.0 5.0 7.4 8.6 3.6 4.4 6.0 7.4
High 330 330 330 390 330 330 390 390
Low 245 245 245 340 245 245 340 340
High 360 360 360 410 360 360 410 410
Low 270 270 270 370 270 270 370 370
40* 65* 65* 65* 65* 65* 65* 65*
1.7 2.2 2.2 4.4 2.2 2.2 4.4 4.4
111 112 123 126 108 112 124 125
131 127 141 143 123 127 142 142
Voltage ¹, ³
Amps10
Watts10
Min. Circuit Amps ², 4, 10
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Ventilated Air, CFM (Fan Only)*
Dehumidification (Pints/Hr.)
Net Weight (lbs.)
Ship Weight (lbs.)
Capacity (BTU/h)
EER
Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
³ Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
5Heating capacity and efficiency based on unit operation without condensate pump.
6Specify two-digit heater kW size to complete model number.
7R-410A refrigerant used in all systems. R-134A used in Kit Fresh Air.
8All units meet or exceed ASHRAE 90.1 standards.
9 All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
10 Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
4Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay fuses
(included and factory-installed on all Amana® brand 265-volt chassis). See heater perform
 - Energy E󰀩ciency Ratio per The Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) Test Procedures and Canadian
Standards Association (CSA) Test Procedures.
 - Coe󰀩cient of Performance per AHRI Test Procedures

SPECIFICATIONS
9
HEH073H
**AXXX
HEH093H
**AXXX
HEH123H
**AXXX
HEH074H
**AXXX
HEH094H
**AXXX
HEH124H
**AXXX
HEH153H
**AXXX
HEH154H
**AXXX
230 / 208 230 / 208 230 / 208 265 265 265 265 265
7,100 /7,000 9,000 / 9,000 11,600 / 11,400 7,700 9,100 12,000 14,200 / 14,00 14,400
3.9 / 3.9 4.7 / 4.7 6.6 / 6.6 3.6 4.2 5.4 7.4 / 7.4 6.4
545 / 525 705 / 705 1,005 / 990 595 730 1,040 1,390 / 1,370 1,410
13.0 / 13.3 12.7 / 12.7 11.5 / 11.5 12.9 12.4 11.5 10.2 / 10.2 10.2
4.6 5.6 7.9 3.6 4.9 6.4 8.9 7.7
High 340 330 340 340 330 340 390 390
Low 245 245 245 245 245 245 340 340
High 370 360 370 370 360 370 390 390
Low 270 270 270 270 270 270 370 370
65* 65* 65* 65* 65* 65* 65* 65*
1.7 2.2 3.6 1.7 2.2 3.6 4.4 4.4
107 111 114 107 111 114 125 125
122 126 131 122 126 131 142 142
Model ¹, 6, 8, 9
Voltage ¹, ³
Capacity (BTU/h)
Amps10
Watts10
EER
Net Weight (lbs.)
Ship Weight (lbs.)
Unit without Electric Heater
Min. Circuit Amps ², 4, 10
CFM (Cool/Wet Coil)
CFM (Dry Coil)
Ventilated Air, CFM (Fan Only)*
Dehumidification (Pints/Hr.)
Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
³ Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
5Heating capacity and efficiency based on unit operation without condensate pump.
6Specify two-digit heater kW size to complete model number.
7R-410A refrigerant used in all systems. R-134A used in Kit Fresh Air.
8All units meet or exceed ASHRAE 90.1 standards.
9 All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
10 Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
4Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay fuses
(included and factory-installed on all Amana® brand 265-volt chassis). See heater perform
 - Energy E󰀩ciency Ratio per The Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) Test Procedures and Canadian
Standards Association (CSA) Test Procedures.
 - Coe󰀩cient of Performance per AHRI Test Procedures


SPECIFICATIONS
10
PTH
073G**
PTH
074G**
PTH
093G**
PTH
123G**
PTH
153G**
PTH
094G**
PTH
124G**
PTH
154G**
230 / 208 265 230 / 208 230/208 230 / 208 265 265 265
BTU/h56,500 / 6,400 6,800 8,200 / 8,000 10,600 /10,500 13,900 / 13,700 8,300 11,300 13,700
3.3 / 3.3 3.0 4.1 / 4.1 6.1 / 6.1 7.0 / 7.0 3.6 4.9 6.1
560 / 535 585 705 / 685 970 / 960 1,350 / 1330 715 1,065 1,335
COP53.4 / 3.5 3.4 3.4 / 3.4 3.2 / 3.2 3.0 / 3.0 3.4 3.1 3.0
360 360 360 360 410 360 410 410
CFM (Dry)
Model
Voltage ¹, ³
Amps10
Watts10
PMH
073G
*
PMH
074G
*
PMH
093G
*
PMH
094G
*
PMH
123G
*
PMH
124G*
*
PMH
153G*
*
230 / 208 265 230 265 230 265 230
BTU/h56,200 / 6,100 6700 7,800 / 7,600 8,000 10,600 / 10,400 11,300 13,800 / 13,600
3.4 / 3.4 3.1 4.2 / 4.2 4.2 6.2 / 6.2 5.0 7.4 / 7.4
530 / 495 595 670 / 655 710 1,000 / 980 1065 1345 / 1325
COP53.4 / 3.5 3.3 3.4 / 3.4 3.3 3.1 / 3.1 3.1 3.0 / 3.0
CFM (Dry) 360 360 360 360 360 360 410
Heating Capacity
Voltage ¹, ³
Amps10
Watts10
Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
³ Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
5
Heating capacity and efficiency based on unit operation without condensate pump.
6
Specify two-digit heater kW size to complete model number.
7
R-410A refrigerant used in all systems. R-134A used in Kit Fresh Air.
8
All units meet or exceed ASHRAE 90.1 standards.
9
All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
10
Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
4
Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay fuses
(included and factory-installed on all Amana® brand 265-volt chassis). See heater perform
 - Energy E󰀩ciency Ratio per The Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) Test Procedures and Canadian
Standards Association (CSA) Test Procedures.
 - Coe󰀩cient of Performance per AHRI Test Procedures
HEH073H**AXXX HEH093H**AXXX HEH123H**AXXX HEH074H**AXXX HEH094H**AXXX HEH124H**AXXX HEH153H**AXXX HEH154H**AXXX
230 / 208 230 / 208 230/208 265 265 265 265 230
BTU/h
5
6,500 / 6,400 8,200 / 8,000 10,600 /10,500 6,800 8,300 11,400 13,700 13,900 13,700
3.9 / 3.9 4.7 / 4.7 6.6 / 6.6 3.6 4.2 5.4 6.4 7.4 / 7.4
545 / 525 665 / 650 910 / 930 550 690 1,075 1,295 1,310 / 1,295
COP
5
3.7 / 3.8 3.6 / 3.6 3.4 / 3.3 3.6 3.5 3.1 3.1 3.1 / 3.1
CFM (Dry) 360 370 370 360 370 370 410 410
Heating Capacity¹
Voltage ¹, ³
Amps
10
Watts
10


Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
³ Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
5
Heating capacity and efficiency based on unit operation without condensate pump.
6
Specify two-digit heater kW size to complete model number.
7
R-410A refrigerant used in all systems. R-134A used in Kit Fresh Air.
8
All units meet or exceed ASHRAE 90.1 standards.
9
All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
10
Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
4
Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay fuses
(included and factory-installed on all Amana® brand 265-volt chassis). See heater perform
 - Energy E󰀩ciency Ratio per The Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) Test Procedures and Canadian
Standards Association (CSA) Test Procedures.
 - Coe󰀩cient of Performance per AHRI Test Procedures