Maytag MLG22PRTKW User manual

www.maytagcommerciallaundry.comW11695009A
4
IMPORTANT SAFETY INSTRUCTIONS
precautions, including the following:
WARNING:
Read all instructions before using the dryer.
Keep a minimum clearance of 100 mm (4 in.) between the
rear of the dryer and any wall.
The operation of this appliance may affect the operation of
other types of appliances which take their air supply for safe
combustion from the same room. There has to be adequate
ventilation to replace exhausted air and thus avoid the
back-ow of gases into the room from appliances burning
other fuels, including open res, when operating the tumble
dryer. If in doubt, consult the appliance manufacturers.
Do not obstruct the air supply to the dryer (see Installation
Instructions for minimum clearances).
Do not place items exposed to cooking oils in your dryer.
Oil-affected items can ignite spontaneously, especially when
exposed to heat sources such as in a tumble dryer. The
items become warm causing an oxidation reaction in the oil.
Oxidation creates heat. If the heat cannot escape, the items
can become hot enough to catch re. Piling, stacking or
storing oil-affected items can prevent heat from escaping
and so create a re hazard.
If it is unavoidable to dry in the dryer items that have been
soiled with substances such as cooking oil, acetone, alcohol,
petrol, kerosene, spot removers, turpentine, waxes and wax
removers, or that have been contaminated by hair care
products, should be washed in hot water with an extra
amount of detergent before being dried in the dryer. These
items may give off vapours that could ignite or explode. Such
washing will reduce, but not eliminate, the hazard.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instructions concerning
use of the appliance by persons responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
The dryer should not be used if industrial chemicals have
been used for cleaning.
Before the dryer is removed from service or discarded,
remove the doors to the drying compartment.
Do not reach into the dryer if the drum is moving. A door
switch is tted for your safety.
Do not install or store the dryer where it will be exposed
to the weather.
Do not tamper with controls.
Do not continue to use this appliance if it appears to be
faulty.
Do not repair or replace any part of the dryer or attempt
any maintenance unless specically recommended in this
Use and Care Guide. Repairs and servicing should only
be carried out by competent service personnel.
Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product. Follow their instructions.
Clean dryer lint screen before or after each load. Do not
operate dryer without lint screen in place.
Keep area around the exhaust and inlet openings and
adjacent surrounding areas free from the accumulation of
lint, dust, and dirt.
The interior of the dryer and exhaust vent should be
cleaned periodically by qualied service personnel.
See Installation Instructions for earthing instructions.
Do not dry unwashed items in this dryer.
Items such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber backed articles and clothes or
pillows tted with foam rubber pads must only be dried
on a clothesline.
SAVE THESE INSTRUCTIONS
WARNING: Never stop a tumble dryer cycle before the
end of the drying cycle unless all items are quickly removed
and spread out so that the heat is dissipated.
To reduce the risk of re, electric shock, or injury to persons when using the dryer, follow basic
The nal part of a tumble dryer cycle occurs without heat
(cool down cycle) to ensure that the items are left at a
temperature that ensures the items will not be damaged.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualied
person in order to avoid a hazard.
INSTALLATION INSTRUCTIONS
ORIGINAL INSTRUCTIONS
COmmeRCIAL STACked
WASheR/dRyeR
GAS
INSTRUCTIONS D’INSTALLATIONS
INSTRUCTIONS D’ORIGINE
LavEUSE/SéChEUSE SUpERpOSéES
aU Gaz àUSaGE COmmERCIaL
INSTRUCCIONES DE INSTALACIÓN
INSTRUCCIONES ORIGINaLES
LavaDORa/SECaDORa apILabLE COmERCIaL aGaS

2
TABLE OF CONTENTS
Page
TABLE DES MATIÈRES
Page
Stacked Washer/Dryer Safety............................................................3
Stacked Washer/Dryer Disposal .......................................................6
Tools & Parts.............................................................................................7
Alternate Parts and Accessories .......................................................8
Specifications...........................................................................................8
Dimensions/Clearances .......................................................................9
Stacked Washer/Gas Dryer Installation
Requirements ........................................................................................ 10
Dryer venting requirements ............................................................. 13
Dryer Gas Supply Requirements ................................................... 16
Installing Stacked Washer/Dryer................................................... 16
Washer Drain System ......................................................................... 19
Leveling.................................................................................................... 20
Complete Installation ......................................................................... 21
Reversing Dryer Door Swing (Optional)....................................... 21
Stacked Washer/Dryer Maintenance Instructions................... 24
If You Need Assistance...................................................................... 25
Electronic Control Setup Instructions .......................................... 26
Sécurité de la laveuse/sécheuse superposées ........................ 32
Élimination de la laveuse/sécheuse superposées .................. 35
Outils et pièces ..................................................................................... 36
Pièces supplémentaires et accessoires ...................................... 37
Spécifications........................................................................................ 37
Dimensions/dégagements ............................................................... 38
Critères d’installation pour la laveuse/sécheuse à gaz
superposées........................................................................................... 39
Exigences concernant l’évacuation de la sécheuse .............. 42
Spécifications de l’alimentation de la sécheuse à gaz ......... 45
Installation de la laveuse/sécheuse superposées................... 45
Système de vidange de la laveuse................................................. 48
Mise à niveau......................................................................................... 49
Achever l’installation .......................................................................... 50
Inversion du sens d’ouverture de la porte de la
sécheuse (optionnel) .......................................................................... 50
Instructions d’entretien de la laveuse/sécheuse
superposées........................................................................................... 53
En cas de besoin d’assistance ........................................................ 54
Instruction de réglage du tableau de commande
électronique ........................................................................................... 55
ÍNDICE
Página
Seguridad de la lavadora/secadora apilable............................. 61
Desecho de la lavadora/secadora apilable................................ 64
Herramientas y piezas........................................................................ 65
Piezas y accesorios adicionales..................................................... 66
Especificaciones................................................................................... 66
Dimensiones/espacios libres.......................................................... 67
Requisitos de instalación de la lavadora/secadora a
gas apilable............................................................................................ 68
Requisitos de ventilación de la secadora .................................. 71
Requisitos del suministro de gas de la secadora .................... 74
Instalación de la lavadora/secadora apilable ........................... 74
Sistema de desagote de la lavadora............................................. 77
Nivelación................................................................................................ 78
Instalación completa .......................................................................... 79
Cambio de sentido de la abertura de la puerta
(opcional) ................................................................................................ 79
Instrucciones de mantenimiento de la lavadora/
secadora apilable................................................................................. 82
Si necesita asistencia......................................................................... 83
Instrucciones de programación del control electrónico........ 84

3
STACKED WASHER/DRYER SAFETY
nIt is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer
smells gas. This information should be obtained from your gas supplier.
nPost the following warning in a prominent location.
FOR yOUR SAFeTy
1. DO NOT USE OR STORE PETROL OR OTHER FLAMMABLE MATERIALS IN THIS APPLIANCE OR NEAR THIS APPLIANCE.
2. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
3. DO NOT MODIFY THIS APPLIANCE.
4. DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
5. DO NOT USE OR STORE FLAMMABLE MATERIALS IN OR NEAR THIS APPLIANCE.
WARNING –
RISK OF FIRE/FLAMMABLE MATERIALS
This is an additional safety alert symbol that alerts you to the risk of re. Care is required to avoid causing
are by igniting ammable material.

4
STACKED WASHER/DRYER SAFETY
WARNING:
•
•
•
•
•
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury, death or property damage.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
If you cannot reach your gas supplier, call the fire department.
– Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic precautions,
including the following:
SAVE THESE INSTRUCTIONS
-CONTINUED ON NEXT PAGE-
nRead all instructions before using the washer/dryer.
nThis dryer is intended only for drying clothes and textiles
that have been washed in water. Do not use for any other
purpose.
nWARNING: If you smell gas, do not use the dryer or any
electrical equipment nearby. Warn other people to clear the
area. Contact the washer/dryer owner immediately.
nOil-affected items can ignite spontaneously, especially
when exposed to heat sources such as a tumble dryer. The
items become warm, causing an oxidation reaction in the
oil. Oxidation creates heat. If the heat cannot escape, the
items can become hot enough to catch fire. Piling, stacking
or storing oil-affected items can prevent heat from escaping
and so create a fire hazard.
nIf it is unavoidable that fabrics that contain vegetable or
cooking oil or that have been contaminated by hair care
products be placed in a tumble dryer, they should first be
washed in hot water with extra detergent – this will reduce,
but not eliminate, the hazard.
4
IMPORTANT SAFETY INSTRUCTIONS
precautions, including the following:
WARNING:
Read all instructions before using the dryer.
Keep a minimum clearance of 100 mm (4 in.) between the
rear of the dryer and any wall.
The operation of this appliance may affect the operation of
other types of appliances which take their air supply for safe
combustion from the same room. There has to be adequate
ventilation to replace exhausted air and thus avoid the
back-ow of gases into the room from appliances burning
other fuels, including open res, when operating the tumble
dryer. If in doubt, consult the appliance manufacturers.
Do not obstruct the air supply to the dryer (see Installation
Instructions for minimum clearances).
Do not place items exposed to cooking oils in your dryer.
Oil-affected items can ignite spontaneously, especially when
exposed to heat sources such as in a tumble dryer. The
items become warm causing an oxidation reaction in the oil.
Oxidation creates heat. If the heat cannot escape, the items
can become hot enough to catch re. Piling, stacking or
storing oil-affected items can prevent heat from escaping
and so create a re hazard.
If it is unavoidable to dry in the dryer items that have been
soiled with substances such as cooking oil, acetone, alcohol,
petrol, kerosene, spot removers, turpentine, waxes and wax
removers, or that have been contaminated by hair care
products, should be washed in hot water with an extra
amount of detergent before being dried in the dryer. These
items may give off vapours that could ignite or explode. Such
washing will reduce, but not eliminate, the hazard.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instructions concerning
use of the appliance by persons responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
The dryer should not be used if industrial chemicals have
been used for cleaning.
Before the dryer is removed from service or discarded,
remove the doors to the drying compartment.
Do not reach into the dryer if the drum is moving. A door
switch is tted for your safety.
Do not install or store the dryer where it will be exposed
to the weather.
Do not tamper with controls.
Do not continue to use this appliance if it appears to be
faulty.
Do not repair or replace any part of the dryer or attempt
any maintenance unless specically recommended in this
Use and Care Guide. Repairs and servicing should only
be carried out by competent service personnel.
Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product. Follow their instructions.
Clean dryer lint screen before or after each load. Do not
operate dryer without lint screen in place.
Keep area around the exhaust and inlet openings and
adjacent surrounding areas free from the accumulation of
lint, dust, and dirt.
The interior of the dryer and exhaust vent should be
cleaned periodically by qualied service personnel.
See Installation Instructions for earthing instructions.
Do not dry unwashed items in this dryer.
Items such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber backed articles and clothes or
pillows tted with foam rubber pads must only be dried
on a clothesline.
SAVE THESE INSTRUCTIONS
WARNING: Never stop a tumble dryer cycle before the
end of the drying cycle unless all items are quickly removed
and spread out so that the heat is dissipated.
To reduce the risk of re, electric shock, or injury to persons when using the dryer, follow basic
The nal part of a tumble dryer cycle occurs without heat
(cool down cycle) to ensure that the items are left at a
temperature that ensures the items will not be damaged.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualied
person in order to avoid a hazard.
nDo not wash or dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with petrol, dry-cleaning
solvents, other flammable, or explosive substances as they
give off vapors that could ignite or explode.
nItems that have been soiled with substances such as acetone,
alcohol, petrol, kerosene, spot removers, turpentine, waxes,
and wax removers should be washed in hot water
with extra detergent before being dried
in the dryer.
nDo not add petrol, dry-cleaning solvents, or other flammable,
or explosive substances to the wash water. These substances
give off vapors that could ignite or explode.
nDo not dry unwashed items in the dryer.
nDo not use this dryer if industrial chemicals have been used
for cleaning. The possible presence of residual quantities
of aggressive or decomposed chemicals in the load may
produce damage to the dryer and harmful fumes.
nDo not allow children to play on or in the washer/dryer. Close
supervision of children is necessary when the washer/dryer is
used near children. Cleaning and user maintenance shall not
be made by children without supervision. Children of less than
3 years should be kept away unless continuously supervised.

5
STACKED WASHER/DRYER SAFETY
nThe final part of a tumble dryer cycle occurs without heat
(cool-down cycle) to ensure that the articles are left at a
temperature that ensures that the items will not be damaged.
nWARNING: Never stop a tumble dryer before the end of
the drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated. (Avoids risk of
spontaneous combustion).
nWARNING: The appliance must not be supplied through an
external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by a utility.
nIn case of electrical supply failure, remove the load quickly
and spread it out to avoid risk of spontaneous combustion.
nKeep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
nVentilation openings in the base shall not be obstructed by a
carpet or similar object.
nThe fresh air ventilation openings into the room and into the
dryer must not be blocked or sealed.
nEmergency stop control: After installation, access to mains
plug or disconnection from mains supply via a double-pole
switch must be ensured at all times in order to ensure
immediate deactivation of the dryer in case of emergency.
nThe interior of the dryer and dryer exhaust vent should be
cleaned periodically by qualified service personnel.
nSee “Electrical Requirements” section for earthing
instructions.
nAdequate ventilation has to be provided to avoid the
back-flow of gases into the room from appliances burning
fuels, including open fires.
nThe new hose-sets supplied with the appliance are to be
used. Old hose-sets should not be reused.
nExhaust air must not be discharged into a flue which is used
for exhausting fumes from appliances burning gas or other
fuels.
nThis appliance must not be installed behind a lockable door,
a sliding door or a door with a hinge on the opposite side to
that of the tumble dryer, in such a way that a full opening of
the tumble dryer door is restricted.
nOnly authorized spare parts shall be used in the event of
failure.
nIf an error code is displayed, contact the owner. The owner
shall call service.
nSee DIMENSIONS/CLEARANCES section for minimum
installation spacing requirements
nDryer IEC Load Capacity: 10.5 kg.
nWasher IEC Load Capacity: 10.5 kg.
nThis appliance is intended, but not limited, to be used in
public areas.
nThis washer/dryer is not intended for use by persons
(including children) with reduced physical, sensory, or
mental capabilities, or lack of experience or knowledge,
unless they have been given supervision or instruction
concerning use of the dryer by a person responsible for their
safety.
nBefore the washer/dryer is removed from service or
discarded, remove the doors to the washer/dryer
compartments.
nDo not reach into the washer/dryer if the tub, agitator, or
drum is moving.
nOpening the dryer door will stop the function of the dryer.
nWhen loading or re-loading the dryer, avoid touching hot
metal parts of the drum (burn risk).
nRemove all objects from pockets such as lighters and
matches.
nThe appliance must be disconnected from its power source
during service and when replacing parts.
nIf drum rotation is blocked due to trapped textiles,
disconnect the dryer from the electrical supply before gently
removing the blockage.
nIf the dryer is not heating, or appears to be defective or
damaged, do not use it. Contact the owner.
nDo not install or store the washer/dryer where it will be
exposed to the weather.
nDo not tamper with controls.
nThis appliance incorporates an earth connection for
functional purposes only.
nClean dryer lint screen before or after each load.
nDo not use this dryer without the lint screen in place.
nUnder certain conditions, hydrogen gas may be produced
in a hot water system that has not been used for 2 weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using
the washer, turn on all hot water faucets and let the water
flow from each for several minutes. This will release any
accumulated hydrogen gas. As the gas is flammable, do not
smoke or use an open flame during this time.
nDo not repair or replace any part of the washer/dryer or
attempt any servicing unless specifically recommended
in this Use and Care Guide or in published user-repair
instructions that you understand and have
the skills to carry out. If the supply cord is damaged, it
must be replaced by the manufacturer, its service agent, or
similarly qualified persons in order to avoid a hazard.Fabric
softeners, or similar products, should be used as specified
by the fabric softener instructions.
nItems such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber-backed articles, and clothes or
pillows fitted with foam rubber pads should not be dried in
the tumble dryer.
SAVE THESE INSTRUCTIONS

6
STACKED WASHER/DRYER DISPOSAL
This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment
(WEEE).
By ensuring this product is disposed of correctly, you will help avoid potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be
treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical
and electronic equipment.
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your local city ofce,
your household waste disposal service or the shop where you purchased the product.
MODEL NOMENCLATURE:
MLG – Maytag Stacked Laundry Gas Dryer PD – Electronic Control – Coin Drop Enabled
22 – Stacked Washer/Dryer Model PR - Electronic Control - Card Ready

7
Tools and parts needed:
TOOLS & PARTS
†TORX and T20 are trademarks of Acument Intellectual Properties, LLC.
Parts Supplied:
A B
D
E
CA. Water Inlet Hoses (2)
B. Inlet Hose Washers (4)
C. Drain hose with clamp, U-form
D. Transit Bolt Hole Plug (4)
E. Beaded Tie Strap
G
ABC
DEF
HI
J
NO
L
K
M
P
QR
A. 8" (200 mm) or 10" (250 mm) Pipe Wrench
B. 8" (200 mm) or 10" (250 mm) Adjustable
Wrench that opens to 1" (25 mm)
C. Flat-Blade Screwdriver
D. Phillips Screwdriver
E. TORX T20†Security Screwdriver or Bit
F. 1" (25 mm) Hex-Head Socket Wrench
G. 5/16" (8 mm) Socket Wrench
H. Pliers that open to 19/16" (39 mm)
I. Level
J. Utility Knife
K. 1/4" (6 mm) Nut Driver
L. Locking Pliers
M. Caulk Gun and Caulk
(for installing new exhaust vent)
N. Vent Clamps
O. Pipe-Joint Compound Suitable for Gas Type
P. 27" (686 mm) Wood Block
Q. 1/2" (13 mm) and 9/16" (14 mm)
Open-End Wrenches
R. Ruler or Measuring Tape

8
ALTERNATE PARTS AND ACCESSORIES
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, contact your authorised
Maytag distributor.
If You Have You Will Need to Buy
Overhead sewer Standard 76 L (20 gallon) 990 mm (39")
tall drain tub or utility sink, sump pump
and connectors (available from local
plumbing suppliers)
25 mm (1") standpipe 51 mm (2") diameter to 25 mm (1")
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Drain hose too Extension Drain Hose Part
short Number DRNEXT4
Connector Kit Part Number 285835
Lint clogged drain Drain Protector Part Number 367031
Connector Kit Part Number 285835
Floor drain system Siphon Break, Part Number 285834
Connector Kit (x2) Part Number 285835
Extension Drain Hose Part
Number 285863
Water faucets Two longer water fill hoses:
beyond reach 1.8 m (6 ft) 90° bend hose
of fill hoses Part Number 76314
3.0 m (10 ft) Part Number 350008
SPECIFICATIONS
These units are sold in multiple regions with different
requirements for measuring capacity. Below are a few
of the valid forms of measure posted on this product:
Dry Linen Capacity: A weight measure that reflects a minimum
threshold for dry volume capacity that is needed for import tariff
purposes.
IEC Capacity: The capacity measure that represents the maximum
capacity of dry linens and textiles which the manufacturer declares
can be treated in a specific cycle.
220 V-240 V~60 Hz 1ph 10 A maximum IPX4 Total mass: 174
kg maximum
Factory set for NATURAL GAS: Injector size: 2.2 mm; Heat input
gross: 5.9 kW; Supply Pressure (G20): 20 mbar; Factory adjusted
Pressure: 7.4 mbar
With L.P. gas Conversion Kit: Injector size:
1.25 mm; Heat input gross: 6.4 kW
Butane Supply Pressure (G30): 28-30 mbar
L.P. Supply Pressure (G31): 37 mbar
Washer Dryer
Dry Linen Capacity
10.5 kg (23 lb) 10.5 kg (23 lb)
IEC Capacity
10.5 kg (23 lb) 10.5 kg (23 lb)
Sound Level
LpA: 58 dB(A) (Kpa+/-10 dB(A))
Accessories
Enhance your washer/dryer with these premium accessories.
For more high-quality items or to order, contact your authorised
Maytag distributor.
Part Number Accessory
8212526 Washer drip tray, fits under all
31682 All-purpose appliance cleaner
1903WH Laundry supply storage cart
279818 Three-way dryer venting kit
285834 Siphon break kit

9
DIMENSIONS/CLEARANCES
Front View
Dimensions
Clearances
Side Clearances
Back ViewSide View
Back/Top Clearances
Electric
Gas Vent
Water Inlets

10
Selecting the proper location for your washer/dryer improves
performance and minimises noise and possible washer “walk.”
Your washer/dryer can be installed in a basement, laundry room,
or recessed area. See “Drain System.”
Companion appliance location requirements should also be
considered.
IMPORTANT: Do not install or store the washer/dryer where
it will be exposed to the weather. Do not store or operate the
washer/dryer in temperatures at or below 0°C (32°F). Some
water can remain in the washer and can cause damage in
low temperatures. Proper installation is your responsibility.
You will need:
nA water heater set to deliver 49°C (120°F) water to the washer.
nAn earthed electrical supply. See “Electrical Requirements.”
nHot and cold water faucets located within 1.2 m (4 ft)
of the hot and cold water fill valves, and water pressure
of 137.9 kPa – 689.6 kPa (20 psi –100 psi).
nA level floor with a maximum slope of 25 mm (1") under
entire washer/dryer. Installing the washer/dryer on soft floor
surfaces, such as carpets or surfaces with foam backing, is
not recommended.
nA sturdy and solid floor to support the washer/dryer with a total
weight (water and load) of 204 kg (450 lbs).
nA floor drain under the bulkhead. Prefabricated bulkheads with
electrical outlets, water inlet lines, and drain facilities should be
used only where local codes permit.
Stacked Washer/Gas Dryer Location
STACKED WASHER/GAS DRYER INSTALLATION
REQUIREMENTS
Stacked washer/gas dryer installation clearances
nThe location must be large enough to allow the washer and
dryer doors to be fully opened.
nAdditional spacing should be considered for ease of installation
and servicing. The doors open more than 180°. The washer
door is not reversible.
nAdditional clearances might be required for wall, door,
and floor mouldings.
nCompanion appliance spacing should also be considered.
When installing a gas dryer:
IMPORTANT: Observe all governing codes and ordinances.
nCheck code requirements: Some codes limit or do not permit
installation of clothes dryers in garages, closets, or sleeping
quarters. Contact your local building inspector.
nMake sure that lower edges of the cabinet, plus the back and
bottom sides of the washer, are free of obstructions to permit
adequate clearance of air openings for combustion air. See
“Recessed Area and Closet Installation Instructions” below
for minimum spacing requirements.
nDo not install on carpet.
Recessed Area and Closet Installation Instructions
This washer/dryer may be installed in a recessed area or closet.
This washer/dryer must not be installed behind a lockable door,
a sliding door, or a door with a hinge on the opposite side to that of
the washer/dryer in such a way that a full opening of the
washer/dryer is restricted. For recessed area and closet
installations, minimum clearances can be found on the warning label
on the rear of the dryer or in “Dimensions/Clearances.”
The installation spacing is in millimeters and is the minimum
allowable. Additional spacing should be considered for ease
of installation, servicing, and compliance with local codes and
ordinances.
If closet door is installed, the minimum unobstructed air opening in
the top and bottom of the door should be as depicted in the diagram
below. Louvered doors with equivalent air openings are acceptable.
The dryer must be exhausted outdoors.
No other fuel-burning appliance may be installed in the same
closet as the washer/dryer.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not install in a garage.
Failure to do so can result in death, explosion, or fire.

11
STACKED WASHER/GAS DRYER INSTALLATION
REQUIREMENTS
Stacked Washer/Gas Dryer Electrical Requirements
•If a crimped wire terminal is used instead of bare wire, it
must be located between the screw head and terminal tab.
Remove the screw and place the crimped contact on the
terminal tab with the crimp seam up, then reinsert the screw.
To minimize the potential for cross-threading, initially rotate
the screw counterclockwise and then rotate clockwise until
secure. Torque to 4 Nm (35 in-lbf) minimum.
nA 10 A supply fuse should be used, and a switch having
a contact separation in both poles that provides full
disconnection under over-voltage category III conditions must
be incorporated into the fixed wiring in accordance with local
wiring regulations. The washer/dryer should be positioned
so that the disconnection switch is clearly visible and easily
accessible to the user.
This disconnection switch also provides the function of an
emergency stop control for the user.
nA cord clamp bushing is provided on the washer/dryer, and
should be tightened on completion of wiring. Remember to
replace the terminal access panel (terminal block cover).
nDo not earth to a gas pipe.
IMPORTANT: Observe all governing codes and ordinances.
NOTE: In accordance with the European EMC Directive
(2014/30/EU), the maximum electricity supply system impedance to
which the gas dryer should be connected is declared to be
0.054 Ω+ j0.034 Ω.
NOTE: Electrical safety standards: The manufacturer has chosen
compliance with IEC/EN 60335 standards as the most appropriate
for this product.
Fixed Wiring Installation (Terminal Block)
The washer/dryer is supplied without an electric cord and plug. It
must be connected by a competent electrician to a single-phase
electricity supply at the voltage shown on the dataplate, using a
suitable fixed wiring installation in accordance with local and national
wiring regulations.
nA 3-wire circular cord of minimum conductor
size 2.5 mm2(14 AWG) cross-section area should be used.
nThe electrical mains terminals are located behind the small rear
access panel (terminal block cover), and connections should
be made in accordance with the terminal markings.
•Insure that a 3980399 Square Washer (part of furnished
W10545880 Bag Assembly - Square Washer) is installed
between the head of the terminal screw head and the
terminal tab. To install, remove the screw, place the square
washer on the screw, and partially reinsert the screw. To
minimize the potential for cross-threading, initially rotate the
screw counterclockwise and then rotate clockwise. Bare
wire must be placed between the square washer and the
terminal tab and secured by the screw.
Torque to 4 Nm (35 in-lbf) minimum.
2.5 mm2
(14 AWG) minimum
Screw Torque
4 Nm (35 in-lbf) minimum
Screw
Square Washer Square Nut
Terminal
Electrical Shock Hazard
This is a 3-wire appliance which must be earthed.
Securely tighten all electrical connections.
Failure to follow these instructions could result in death,
fire, or electric shock.
WARNING

12
Stacked Washer/Gas Dryer Gas Supply Requirements
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (33 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Gas Supply
Before installation, check that the local gas distribution conditions,
nature of gas and pressure, and the adjustment of the appliance
are compatible. Burner information will be found on the
model/serial rating plate in the door recess of the dryer. If this
information does not agree with the type of gas available, see your
dealer.
Recommended Earthing Method
It is your responsibility to contact a qualified electrical installer to
ensure that the electrical installation conformance with all local
codes and ordinances.
STACKED WASHER/GAS DRYER INSTALLATION
REQUIREMENTS
Cord and Plug Installation
WARNING
Electrical Shock Hazard
Plug into a grounded (earthed) outlet.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Do not use an extension cord.
Do not use an adapter.
Do not remove ground prong.
nA 220 V–240 V, 60 Hz., fused electrical supply is required.
A time-delay 10 A–16 A fuse or circuit breaker is
recommended. It is recommended that a separate circuit
serving only this washer/dryer be provided.
nThis washer/dryer is equipped with a power supply cord having
a 3-prong earthed plug.
nAn earthed electrical outlet located within 610 mm (2 feet) of
either side of the washer/dryer shall be furnished.
nTo minimize possible shock hazard, the cord must be plugged
into a mating, 3-prong, earthing-type outlet, earthed in
accordance with local codes and ordinances. If a mating outlet
is not available, it is the personal responsibility and obligation of
the customer to have the properly earthed outlet installed by a
qualified electrician.
nThe washer/dryer shall be disconnected from its power source
during service and when replacing parts.
nThe washer/dryer must be positioned so that the plug is clearly
visible and accessible, such that an operator can check from
any points to which he has access that the plug remains
removed.
If this is not possible, a disconnection with a locking system in
the isolated position shall be provided.
nThis plug also provides the function of an emergency stop
control for the user.
nIf codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
earth path is adequate.
nIf the supply cord is damaged, it must be replaced by the
manufacturer, its service agent, or a qualified person to avoid a
hazard.
nDo not earth to a gas pipe.
nCheck with a qualified electrician if you are not sure the
washer/dryer is properly earthed.
nDo not have a fuse in the neutral or earth circuit.
nPhilippines: Outlet must comply with Philippine National
Standard PNS 1572:1997 Annex A, 250 V,10/15 A, 2-pole,
3-wire, grounding receptacle.
EARTHING INSTRUCTIONS
This washer/dryer must be earthed. In the event of a
malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for
electric current. This washer/dryer is equipped with a cord
having an equipment-earthing conductor and an
earthing plug. The plug must be plugged into an appropriate
outlet that is properly installed and earthed in accordance
with all local codes and ordinances.
Do not modify the plug provided with the appliance – if it
will not fit the outlet, have a proper outletinstalled by
a qualified electrician.
WARNING: Improper connection of the
equipment- earthing conductor can result in a risk of
electric shock. Check with a qualified electrician or
serviceman if you are in doubt as to whether the appliance
is properly earthed.

13
STACKED WASHER/GAS DRYER INSTALLATION
REQUIREMENTS
Supply line requirements:
A. Provide a rigid gas supply line to the washer/dryer location.
It should be minimum 12.5 mm (1/2") ID. When acceptable to
the gas supplier and local codes, 10 mm (3/8") ID rigid supply
line may be used for lengths under 6.1 m (20'). Pipe-joint
compounds resistant to the action of L.P. gas must be used.
B. Gas connection to the dryer itself should be made by means
of a flexible gas hose suitable for the appliance and gas
category in accordance with national installation regulations.
If in doubt, contact the gas supplier. It should be minimum
10 mm (3/8") ID.
A means of restraint should be used between the washer/dryer
and the wall to avoid straining of the rigid gas supply when the
washer/dryer is moved. An appropriate length of chain and a wall
hook is recommended.
The dryer gas inlet connection is a 3/8" NPT thread. An adapter is
supplied for conversion to standard ISO 228-1 thread (3/8" BSP).
A.
B.
Natural Gas:
This dryer is factory adjusted for use with NATURAL GAS (G20),
and no further adjustment should be required at installation.
L.P. Gas:
This dryer is also certified for use with L.P. gas with appropriate
conversion. No attempt shall be made to convert the appliance
from the gas specified on the model/serial rating plate for use
with a different gas without consulting the serving gas supplier.
Conversion must be done by a competent service technician.
L.P. Gas conversion kit, part number W10571757, is available for
purchase from your dealer. Full instructions are supplied with the
kit.
Check for leaks by using an approved noncorrosive leak-detection
solution. Bubbles will show a leak. Correct any leak found.
A pressure measurement tapping is provided on the gas valve
within the dryer, accessible after removal of the lower front panel.
The dryer must be disconnected from the gas supply piping system
during any pressure testing of that system.
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
nFollowing these venting requirements will minimise ducting
air noise.
nAdequate ventilation has to be provided to avoid the backflow
of gases into the room from appliances burning other fuels,
including open fires (i.e. available airflow into the room should
match airflow out from the room).
nDryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, attic, crawlspace, or a concealed space
of a building. Only rigid or flexible metal vent shall be used for
exhausting.
nDo not use an exhaust hood with a magnetic latch.
nOnly a 102 mm (4") heavy, metal exhaust vent and clamps may
be used.
nDo not use plastic or metal foil vent.
nExhaust air must not be discharged into a flue which is used for
exhausting fumes from appliances burning gas or other fuels.
nForced ventilation of fresh air is required.
nExhaust air must be exhausted to the outside to avoid
suffocation.
nIf exhaust is connected to a commonly used exhaust system, it
is required to install flap valves at each connection or alternative
adequate countermeasures.
nExhaust air must not be connected to an exhaust channel
of a furnace.
102 mm
( 4" )
102 mm (4") Heavy, Metal Exhaust Vent
DRYER VENTING REQUIREMENTS

14
Rigid metal vent:
nRecommended for best drying performance and to avoid
crushing and kinking.
Flexible metal vent: (Acceptable only if accessible to clean)
nMust be fully extended and supported in final dryer location.
nRemove excess to avoid sagging and kinking that may result
in reduced airflow and poor performance.
nDo not install in enclosed walls, ceilings, or floors.
nThe total length should not exceed 2.4 m (73⁄4ft).
nAn exhaust hood should cap the vent to keep rodents and
insects from entering the building.
NOTE: If using an existing vent system, clean lint from entire length
of the system and make sure exhaust hood is not plugged with lint.
Replace plastic or metal foil vents with rigid metal or flexible metal
vents. Review “Vent System Chart” and if necessary, modify exist-
ing vent system to achieve best drying performance.
Elbows:
n45° elbows provide better airflow than 90° elbows.
nPlan installation to use the fewest number of elbows and turns.
nAllow as much room as possible when using elbows or making
turns. Bend vent gradually to avoid kinking.
nVent outlet is located at the centre of the bottom dryer back.
nThe vent can be routed up, down, left, right, behind the dryer,
or straight out the back of the dryer.
nClamps:
nUse clamps to seal all joints.
nExhaust vent must not be connected or secured with screws
or other fastening devices that extend into interior of duct and
catch lint. Do not use duct tape.
Better
Good
Vent Hoods
102 mm (4") Diameter Exhaust Hoods
Box Hood Louvered Hood Angled Hood
Maximum Vent Length/Vent Connection
Maximum length of vent system depends upon the type of vent
used, number of elbows, and type of exhaust hood.
Vent System Chart (Rigid Metal Vent)
No. of Box and Angled
90˚Turns Louvered Hood Hood
0 39.6 m (130 ft) 39.3 m (129 ft)
1 38.1 m (125 ft) 36.3 m (119 ft)
2 35.1 m (115 ft) 33.2 m (109 ft)
3 32.3 m (106 ft) 30.5 m (100 ft)
4 29.9 m (98 ft) 28.0 m (92 ft)
For vent systems not covered by the vent specification chart,
see your parts distributor.
Provision must be made for enough air for combustion and
ventilation. (Check governing codes and ordinances.) See
“Recessed Area and Closet Installation Instructions” in the
“Stacked Washer/Gas Dryer Location” and “Stacked Washer”
sections.
A 102 mm (4") outlet hood is preferred. However, a 64 mm (21⁄2")
outlet exhaust hood may be used. A 64 mm (21⁄2") outlet creates
greater back pressure than other hood types. For permanent
installation, a stationary vent system is required.
Connect Vent
1. If connecting to existing vent, make sure the vent is clean.
2. Using a 102 mm (4") clamp, connect vent to exhaust outlet
in dryer.
NOTE: Do not remove vent collar.
Vent System Length
Vent Collar
12" min.
(305 mm)
Exhaust hood must be at least 305 mm (12") from the ground or
any object that may be in the path of the exhaust (such as flowers,
rocks, bushes, or snow).
305 mm minimum
(12")
DRYER VENTING REQUIREMENTS

15
DRYER VENTING REQUIREMENTS
3. Tighten hose clamp with Phillips screwdriver.
4. Make sure the vent is secured to exhaust hood with a
102 mm (4") clamp.
5. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
If an Exhaust Hood Cannot be Used
The outside end of main vent should have a sweep elbow directed
downward.
If main vent travels vertically through the roof, rather than through
wall, install a 180° sweep elbow on end of vent at least
610 mm (2 ft) above surface of roof.
The opening in wall or roof shall have a diameter 13 mm (1⁄2")
larger than vent diameter. Vent should be centred in opening.
Do not install screening over end of vent for best performance.
"
mínimomm
305
12 "
mínimomm
610
24
*Minimum clearance above
any accumulation of
snow, ice, or debris such
as leaves
A main vent can be used for venting a group of dryers. The main
vent should be sized to remove 5663 l/min. (200 CFM) of air per
dryer. Large-capacity lint screens of proper design may be used in
main vent if checked and cleaned frequently. The room where the
dryers are located should have make-up air equal to or greater than
CFM of all the dryers in the room.
Unobstructed air openings are required for make up combustion
air. A static opening of 24 square inches (1 inch2per 1,000 BTU
of burner) is the minimum required for each dryer in operation.
A common opening may be used if the return air is distributed
equally to all dryers in operation.
Back-draft Damper Kit is available from your distributor and should
be installed in the vent of each dryer to keep exhausted air from
returning into dryers and to keep exhaust in balance within main
vent. Unobstructed return air openings are required.
Each vent should enter the main vent at an angle pointing in the
direction of the airflow. Vents entering from the opposite side
should be staggered to reduce the exhausted air from interfering
with the other vents.
The maximum angle of each vent entering the main vent should be
no more than 30°.
Keep air openings free of dry cleaning fluid fumes. Fumes create
acids which, when drawn through the dryer heating units, can
damage dryers and items being dried.
A clean-out cover should be located on the main vent for periodic
cleaning of the vent system.
Multiple Dryer Venting
30˚ max.
Air ow

16
Make Gas Connection
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (33 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
INSTALLING STACKED
WASHER/DRYER
IMPORTANT: Position the washer/dryer so that the rear of the
washer is within approximately 900 mm (3 ft) of its final location.
There are four shipping bolts in the rear panel of the washer that
support the suspension system during transportation.
IMPORTANT: Remove the four shipping bolts at the rear of the
washer before operation.
Remove Transport System
NOTE: Slide washer/dryer onto cardboard or hardboard before
moving to avoid damaging floor covering.
1. Remove red cap from gas pipe.
2. Connect gas supply to dryer. If the flexible gas hose has
10 mm (3/8") BSP thread, use the supplied conversion thread
adapter. Use pipe-joint compound resistant to the action of L.P.
gas for gas connections.
If necessary for service, open the toe panel. Use a putty knife
to press on the two toe panel locks located at the top of the
toe panel. Pull downward on the toe panel to open. Toe panel
is hinged at the bottom.
3. Open the shut-off valve in the gas supply line.
4. Test all connections by brushing on an approved, noncorrosive
leak-detection solution. Bubbles will show a leak. Correct any
leaks found.
1. Keep the washer/dryer in the upright position while
removing the shipping bolts.
2. Using a 13 mm (1/2") wrench, loosen each of the bolts.
Shipping bolt
Shipping bolt with plastic spacer
3. Once the bolt is loose, move it to the centre of the hole
and completely pull out the bolt, including the plastic spacer and
store them in a location for use if the unit needs to be moved at
a later date.
IMPORTANT: If the washer is to be transported at a later date,
call your local service center for new transport bolts if the
original set is misplaced. Machine must be transported in the
upright position. To avoid structural or suspension damage to
your washer, it must be properly set up for relocation by a
certified technician.
DRYER GAS SUPPLY REQUIREMENTS

17
INSTALLING STACKED WASHER/DRYER
Connect Inlet Hoses
Insert new hose washers (supplied) into each end of the inlet
hoses. Firmly seat the washers in the couplings.
Connect Inlet Hoses to Water Faucets
Make sure the washer drum is empty.
1. Attach a hose to the hot water faucet. Screw on coupling
by hand until it is seated on the washer.
2. Attach a hose to the cold water faucet. Screw on coupling
by hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve.
Damage to the valves can result.
CouplingWasher
Connect Inlet Hoses to Washer
1. Attach the cold water hose to the washer’s cold water inlet
valve. Screw on coupling by hand until it is seated on the
washer.
2. Attach the hot water hose to the washer’s hot water inlet valve.
Screw on coupling by hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten. Damage to the valve can result.
4. Turn on the water faucets completely and check for leaks.
NOTE: Replace inlet hoses after 5 years of use to reduce the
risk of hose failure. Record hose installation or replacement
dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Clear Water Lines
nRun water through both faucets and inlet hoses, into a laundry
tub, drainpipe, or bucket, to get rid of particles in the water lines
that might clog the inlet valve screens.
nCheck the temperature of the water to make sure that the hot
water hose is connected to the hot water faucet and that the
cold water hose is connected to the cold water faucet.
4. Close the bolt holes with the four transport bolt hole plugs.
IMPORTANT: If the washer/dryer is to be transported, call your
product distributor or installer. To avoid suspension and structural
damage, your washer/dryer must be properly set up for relocation
by a trained professional.

18
INSTALLING STACKED WASHER/DRYER
Route Drain Hose
Proper routing of the drain hose avoids damage to your floor due
to water leakage. Read and follow these instructions.
Remove drain hose from the washer drum
1. Using locking pliers, squeeze hose clamp tabs together and
insert over the end of the drain hose.
2. Slide the drain hose onto the washer connection.
3. Once the drain hose is in place, release the pliers.
Laundry tub drain or standpipe drain
1. Connect the drain hose form to the corrugated drain hose.
2. Snap either end of the drain hose form to the
drain hose at the point where the corrugation
begins.
3. Bend drain hose over drain hose form and
snap into place.
NOTE: Hose must not extend more than
25 mm (1") past the end of the U bend.
To keep drain water from going back into the
washer:
nDo not straighten the drain hose, do not force excess drain
hose into standpipe. Hose should be secure but loose enough
to provide a gap for air.
nDo not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See “Alternate Parts.”
Secure Drain Hose
1. Drape the power cord over the washer top.
2. Move the washer to its final location.
3. Place the drain hose
in the laundry tub or
standpipe as shown.
4. Secure the drain hose using
the supplied beaded tie
strap.
4. The washer drain system can be installed using a floor drain,
wall standpipe, floor standpipe, or laundry tub.
5. If the washer faucets and the drain
standpipe are recessed, put the
hooked end of the drain hose in
the standpipe as shown.
NOTES:
nDo not force excess drain hose
back into the rear of the washer.
nTo avoid siphoning, do not seal
the drain hose into the standpipe.
nTo avoid siphoning, do not seal or
put more than 114 mm (4/") of the drain hose into drainpipe
or standpipe.
nIt is the responsibility of the installer to install and secure the
drain hose into the provided plumbing/drain in a manner that
will avoid the drain hose coming out of, or leaking from, the
plumbing/drain.

19
WASHER DRAIN SYSTEM
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system.
Standpipe drain system – wall or floor
The standpipe drain requires a minimum diameter standpipe of
50 mm (2"). The minimum carry-away capacity can be no less than
38 L (10 gallon) per minute.
The top of the standpipe must be at least 762 mm (30") high
and no higher than 2.4 m (96") from the bottom of the washer.
Laundry tub drain system
The laundry tub needs a minimum 76 L (20 gallon) capacity.
The top of the laundry tub must be at least 762 mm (30")
above the floor.
Floor drain system
The floor drain system requires a siphon break that may be
purchased separately.
The siphon break (Part Number 285834) must be a minimum
of 710 mm (28") from the bottom of the washer. Additional hoses
might be needed.
Floor
Syphon-Break
Wall

20
1. Remove cardboard from beneath washer/dryer. Place a level on
top edges of washer/dryer, checking each side and front. If not
level, tip washer/dryer and adjust feet up or down as shown in
Steps 3 and 4, repeating as necessary.
Leveling Stacked Washer/Dryer
LEVELING
Leveling your washer/dryer properly reduces excess noise and
vibration.
2. Grip washer/dryer from top and rock back and forth, making
sure all four feet are firmly on floor. Repeat, rocking washer/dryer
from side to side. If washer/dryer rocks, go to Step 3 and adjust
leveling feet. If all four feet are in firm contact with floor, go to
Step 4.
4. When washer/dryer is level and all four feet are firmly in contact
with the floor, use a 14 mm or 9/16" open-end or adjustable
wrench to turn jam nuts counterclockwise (as viewed from
above) on leveling feet tightly against washer/dryer cabinet.
HELPFUL TIP: You may want to prop washer/dryer with
wooden block.
3. If washer/dryer is not level, use a 14 mm or 9/16"
open-end or adjustable wrench to turn jam nuts clockwise (as
viewed from above) on feet until they are about 13 mm (1/2")
from the washer/dryer cabinet. Then turn the leveling foot
counterclockwise to lower the washer/dryer or clockwise to
raise the washer/dryer. Recheck levelness of washer/dryer and
that all four feet are firmly in contact with the floor. Repeat as
needed.
HELPFUL TIP: You may want to prop up front of washer/dryer
about 102 mm (4") with a wood block or similar object that will
support weight of washer/dryer.
Jam nut