MB Connect Line mbSECBOX Troubleshooting guide

In the rst step, connect the mbSECBOX to a 10-30V DC
voltage power supply.
Connect any LAN Port 1 thru 4 of the mbSECBOX to the network
interface (ethernet interface) of your computer and an other LAN
Port to your PLC.
or connect the mbSECBOX via the MPI/PROFIBUS port to your
PLC.
For the initial conguration must the conguration PC and the
mbSECBOX must be in the same address range as the PLC.
• Default settings mbSECBOX
IP-Address 192.168.0.253
Subnet mask 255.255.255.0
Login mbsecbox
Password mbsecbox
• Open the internet protocol (TCP/IP) properties by clicking the
local area connection properties button, which allows you to
change your IP address and subnet mask.
• Your computer‘s IP address needs to be in the address range
of “192.168.0.X“, the subnet mask needs to be the same as the
mbSECBOX‘s (255.255.255.0)
Enter the IP address of the mbSECBOX (192.168.0.253) as the
default gateway and DNS server address.
Quick start-up guide
PLC-Backup
& Virus Detection
192 . 168 . 0 . X
255. 255. 255 . 0
192 . 168 . 0 . 253
192 . 168 . 0 . X
255. 255. 255 . 0
192 . 168 . 0 . 253
Start your browser and enter the required IP address
(192.168.0.253) of the mbSECBOX.
For the mbSECBOX login parameters enter the following:
Username: mbsecbox Password: mbsecbox
IMPORTANT:
If the IP address of the mbSECBOX is changed, you will also
need to change the IP address range of your computer.
After all the changes are saved, you‘ll have to conrm a device
reboot in order to get the changes to take effect.
For more information on mbSECBOX you can view our handbook
by going to our website at www.mbconnectline.com.
192.168.0.253/ Publisher:
Copyright © MB Connect Line GmbH 2014
Hereby MB CONNECT LINE acknowledges that the
device mbSECBOX (MDH874) is in complies with the
essential requirements and other relevant
provisions of directive 1999/5/EC. The declaration of
conformity can be found at: www.mbconnectline.com
MB connect line GmbH
Fernwartungssysteme
Winnettener Str. 6
91550 Dinkelsbühl
Germany
+ 49 (0) 700 / MBCONNECT
+ 49 (0) 700 / 62 26 66 32
www.mbconnectline.com
ADVICE!
Change unconditionally and without delay the
default login information!

Minimal conguration
In the tab menu all the necessary settings can be made
Step 1:
Check all System settings and adapt them if necessary.
In particular, network settings, Email settings, Modem settings.
Step 2:
PLC connection settings
Enter your PLC access data (IP, slot, rack, MPI / PROFIBUS
address).
Backup settings
Specify which Blocktypes are to be saved (default “DB”), and
the interval in which the blocktypes are to be backed up.
Blockcheck settings
Specify which Blocktypes are to be tested
(Default “OB, FC, FB”)
and the interval at which these Blocktypes are to be tested.
Conrm your entries and changes in each tab by clicking on
Step 3:
Click Create backup reference on the button.
Depending on the size of the data to back up may take several
minutes. At the end of the backup, a message will appear.
Step 4:
At last activate the Backup and Blockcheck Cycle
by clicking on
If all the information and settings are correct, FC3 LED starts
ashing. Is currently a data backup or data validation performed
FC3 LED is lit permanently. If FC3 LED is off for over 1 second,
the cyclic operation is not running. That is, the communication
with the PLC is interrupted.
Technical Data:
Supported PLC: S7-300, S7-400 (S7-compatible SPS)
Number of supported
PLC
1
Interface Ethernet/Pronet
MPI/PROFIBUS bis 12MBits/s
Reference and backup
storage
1,9GB
Send email Only over a WAN interface, NOT via
modem
Send SMS Only via modem, NOT over Internet via
WAN
Boot time Up to 4 minutes, as is fully tested after
each boot up the memory.
Normally, approx. 1.5 minutes
With the purchase of mbSECBOX you have chosen a quality
product made in Germany.
Our products are manufactured exclusively in Germany and guar-
antee the highest quality.
For the correctness of the content, we can not guarantee.
For the latest information and updates, please visit our website
www.mbconnectline.com/.
Trademarks
The use of any trademark not listed herein is not an indication that
it is freely available for use.
Any reproduction of this document, utilization and communication
of its contents is not permitted without our approval. Offenders will
be liable for damages. All rights reserved.
Printing errors and modications reserved.