MB QUART NAUTIC NHT1C-116B Instruction Manual

The NHT1C clamping system is designed for
towers and support structures that utilize ROUND
tubing. Oval tubing and at structures will not
work with this clamp. The NHT1C clamp can be
used with tube diameters from 1.5” up to 2.75”.
Included are separate bushing sets for all tube
sizes at 1/8” increments. Refer to the table below
to determine your conguration.
Choose a suitable
mounting location
Mounting Location
Dimensions
CAUTION
Always consider consulting a professional audio installer
before installing new speakers. Many manufacturers locate
speakers behind interior panels that require special tools to
remove. Be careful and take your time.
If you are using the speaker wire supplied with your new
speakers make sure that you run the speaker wires only
through safe areas. Do not let speaker wire make contact with
metal edges or hot engine components.
Congratulations on your choice of a MBQuart speaker.
This “Quick Start” Installation guide is meant to help
you complete a basic installation. For more detailed
information on system setting, speaker and subwoofer
conguration, and full specications by model, visit our
website at mbquart.com
It’s a good idea to conrm that you have purchased the
correct size speakers to t your application. If you have any
reservations about being able to complete the installation
yourself, we recommend contacting a professional.
Before you start
Carefully select a route for the audio signal
wires. If using existing speaker wires, conrm
that the wire is in good shape and not
shorted. In the case of an illuminated model,
route a positive and negative wire from a
switched +12V source. Avoid routing wires
through dangerous areas.
Route signal and
illumination wires
Wiring
Tube
Diameter
Tube
Circumference
Clamp Top
Bushing
Bottom
Bushing
1.5 4.71 A 1.50 1.50
1.625 5.10 A 1.63 1.63
1.75 5.50 A 1.75 1.75
1.875 5.89 A none 1.88
2 6.28 B 2.00 2.00
2.125 6.68 B 2.13 2.13
2.25 7.07 B 2.25 2.25
2.375 7.46 B 2.38 2.38
2.5 7.85 B 2.50 2.50
2.625 8.25 B 2.68 2.68
2.75 8.64 B none none
Black ...................................... Audio signal negative
Black w/white stripe ................ Audio signal positive
Black ....................................... Illumination negative
Red ......................................... Illumination positive

MB Quart products are designed and engineered in the USA by
www.maxxsonics.com
Quick Start
Installation Guide
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
N H T 1C -116 B
N H T 1C -116 L B
NAUTIC
MBQ NHTTC QSG 01 - rev1
Your NHT1C speakers can be aligned to “hang
straight” on an angled tube by loosening, rotating
and re-mounting the speaker. Just behind the
speaker mounting holes is a series mounting holes
that can be used to align the speaker in the pod.
If you have purchased an illuminated version, consider getting an N1-RC remote
control. The remote allows you to adjust color, speed and brightness of the
illumination. Check with an authorized MBQuart retailer or check our website
www.mbquart.com for further details.
Adjust the speaker
alignment
Grill alignment
Illumination control