Mcz Maestro 4021004 User manual

INSTALLATION GUIDE EN

MAESTRO CONTROL PANEL

MAESTRO BEDIENTAFEL

CODE 4021004 - LIFT SQUARE STOVES/LIFT VIERECKIGE ÖFEN

CODE 4021005 - LIFT ROUND STOVES/LIFT VIERECKIGE ÖFEN

CODE 4021001 - RECESSED/FÜR EINBAUINSALLATION

CODE 4021002 - WALL MOUNTED/ FÜR WANDINSTALLATION

CODE 4021003 - LIFT HYDRO JAZZ STOVES/ LIFT HYDRO JAZZ

ÖFEN

INSTALLATIONS- UND GEBRAUCHSHANDBUCH DE

TABLE OF CONTENTS

IIIIII

Instructions in English

TABLE OF CONTENTS .................................................................................................. II

INTRODUCTION ..........................................................................................................3

1 WARRANTY CONDITIONS .........................................................................................4

2 GENERAL INFORMATION...........................................................................................6

3 SYSTEM REQUIREMENTS...........................................................................................7

4INSTALLATION.........................................................................................................8

5OPERATION ...........................................................................................................16

6  OPERATING MODE ................................................................................................20

7  VENTILATION .......................................................................................................24

8  BASIC SETTINGSN.................................................................................................25

9  FUNCTIONS..........................................................................................................26

10  SETTINGS...........................................................................................................28

11 INFO MENU........................................................................................................29

INTRODUCTION

Dear Customer,

to get the best performance, we suggest you read the instructions in this manual carefully.

This installation guide is an integral part of the product: ensure that the manual is always supplied with the appliance, even if it changes

owner. If the manual is lost, you can request another copy from the local Technical Dept. or download it directly from the company’s

website.

All local regulations, including those referring to national and European standards, must be observed when installing the appliance.

In Italy, for the installation of systems with a biomass below 35KW, refer to Italian Ministerial Decree 37/08 and the qualied installation

technician with the suitable requirements must issue a certicate of compliance for the system installed. (By system we intend

Stove+Flue+Air vent).

REVISIONS TO THE PUBLICATION

The content of this manual is strictly technical and the property of the manufacturer.

No part of this manual can be translated into another language and/or altered and/or reproduced, even partially, in another form, by

mechanical or electronic means, photocopied, recorded or similar, without prior written approval from the manufacturer.

The company reserves the right to make changes to the product at any time without prior notice. The proprietary company reserves its

rights according to law.

CARE OF THE MANUAL AND HOW TO CONSULT IT

• Take care of this manual and keep it in an easily and quickly accessible place.

• Should the manual be misplaced or destroyed, request a copy from your retailer or directly from the authorisedTechnical Assistance

Department. You can also download it directly from the company’s website.

• “Bold text”requires special attention.

• “Text in italics”is used to draw your attention to other paragraphs in the manual or for any additional clarications.

• “NOTE”provides the reader with additional information.

SYMBOLS USED IN THE MANUAL

ATTENTION:

Read the corresponding message with care because failure to observe the information provided could

result in serious damage to the product and danger to the persons who use it.

INFORMATION:

failure to comply with these provisions will compromise use of the product.

1- WARRANTY CONDITIONS

444

SAFETY PRECAUTIONS

• The installation, electrical connection, operating

test and maintenance must only be carried out by

authorised and qualied personnel.

• Install the product in accordance with all local and

national legislation and regulations in force in the

region or country.

• The instructions provided in this manual must always be complied with to

ensure the product and any electronic appliances connected to it are used

correctly and accidents are prevented.

• The user, or whoever is operating the product, must read and fully understand

the content of this installation guide before performing any operation. Errors or

incorrect settings can cause hazardous conditions and/or poor operation.

• Any liability for improper use of the product is entirely borne by the user and

relieves the Manufacturer from any civil and criminal liability.

• Any kind of tampering or unauthorised replacement with non-original spare

parts could be hazardous for the operator’s safety and relieves the company

from any civil and criminal liability.

• The product must be powered by an electrical system that is equipped with an

eective earthing system.

• Do not wash the product with water.

• Install the product in a location that does not present a re hazard and is

equipped with power and air supplies, and smoke outlets.

• The product and the cladding must be stored in a dry place and must not be

exposed to weathering.

1- WARRANTY CONDITIONS

WARRANTY CONDITIONS

The company guarantees the product, excluding the components which are subject to normal wear, for a

period of two years from the date of purchase, as proven by a supporting document which gives the name of the vendor and the

date on which the sale took place. The warranty is conditional on the warranty certicate being lled in and returned within 8 days, and

requires that the product be installed and tested by a specialised installer, according to the detailed instructions given in the instruction

manual supplied with the product.

The warranty covers the replacement or free repair of parts recognised as being faulty at source due to

manufacturing defects.

EXCLUSIONS

The warranty does not cover any part that may be faulty as a result of negligence or careless use, incorrect maintenance or installation that

does not comply with the company’s instructions (see the relative chapters in this user manual).

The company does not guarantee that the remote connection to the stove is always active through the Internet network. Thus, it cannot

be held responsible for any damage deriving from failure to connect to the stove.

The company declines all liability for any damage which may be caused, directly or indirectly, to persons, animals or objects as a

consequence of non-compliance with all the prescriptions specied in the manual, especially warnings regarding installation, use and

maintenance of the product.

If the product does not work correctly, contact your local retailer and/or importer.

Damage caused during transport and/or when handled is excluded from the warranty.

The supplied installation guide is the only reference for installation and product use.

The warranty will be considered null and void in the event of damage caused by tampering, atmospheric agents, natural disasters,

electrical discharges, re, defects in the electrical system and maintenance not being performed at all or as indicated by the manufacturer.

2 GENERAL INFORMATION

666

WARNINGS

• The panel must be installed and connected to the motherboard only with electric power DISCONNECTED. The manufacturer will not

be held liable for any malfunctioning in case of damage resulting from failure to comply with this indication.

• Only power on the appliance when the connection to the panel and motherboard is nished

• The connection cable MUST always pass through zones not in contact with the direct heat of the stove or of the combustion chamber.

• Follow the intended passage points for wiring as indicated in this instruction manual

• The connection cable MUST NEVER be more than 2 m long. Any extensions can lead to malfunctioning and loss of communication,

thus entailing anomalous behaviour of the appliance. In this case, the manufacturer disclaims liability for any anomalies, incorrect or

abnormal behaviour of the appliance and damage to the same or to the user.

INFORMATION

• The control panel is a further control interface for the stove and works IN CONJUNCTION with the APPS used from Smartphones, with

the remote control and with the emergency panel on the stove.This means that the commands set from the APP are also displayed

on the panel and vice versa.

• It takes the display 15 seconds to refresh (time required for the display to get the information from the motherboard memory) for

basic commands (power and ventilation) and 3 seconds for operating information (INFO screen).This means that when a command

is given from the APP on the smartphone, there will be a slight delay (max 10 seconds) for it to appear considering the required

times above.

• The optional MAESTRO panel does NOT have an internal probe. Temperature regulations are carried out based on the local probe of

the stove, on the WI-FI probe (optional) and on an external thermostat.

• All optional control panels are compatible with MAESTRO appliances. The various models have dierent assembly supports but the

same internal electronics.The following models are available:

• LIFT: Control panel equipped with push-pull extraction system to be installed on the back of the stove

• LIFT for ROUND stoves: controls equipped with push-pull extraction system to be installed on the back of a round shaped

stove (see HALO, MOOD, etc..)

• RECESSED: Control panel equipped with a wall or plasterboard recessed box to insert the panel in a wall (ideal for MAESTRO

pellet inserts)

• WALL MOUNTED: Control panel equipped with support to be xed to the wall to install the panel near the appliance without

performing masonry work. Also ideal for products which due to their aesthetic features (for example products completely

lined in ceramic like CURVE), the LIFT model control panel cannot be mounted on them

• LIFT for JAZZ hydro stove tted with a panel with knockout hole for insertion and connection purposes

3 SYSTEM REQUIREMENTS

SYSTEM REQUIREMENTS

EQUIPMENT

Equipped with MAESTRO system

OPERATION

The control panel is compatible and operates according to the plug and play logic. Simply perform the electrical connection and fully enjoy

the features of the accessory.

4-INSTALLATION

888

INSTALLATION OF CONTROL PANELS“LIFT”CODE 4021004 AND“LIFT”FOR ROUND STOVES CODE 4021005

The LIFT control panel with vertical push-pull extraction was designed to be installed on the back of the appliance congured accordingly.

Itsconcealedmovement allowsthepaneltoberecovered so that it remains invisiblewhen not used, allowing the aesthetics of the product

to remain unchanged.

MECHANICAL INSTALLATION

Install the panel as shown in the gure, applying the 4 supplied screws“x”on the back of the product.

It is recommended to pre-assemble the 4 screws“x”on the back of the product without tightening them, insert the panel support making

use of the specic slots“y”, fasten the panel with a quick downward movement and then tighten the screws“x”from outside the product.

LIFT CONTROL PANEL CODE 4021004 ROUND LIFT CONTROL PANEL

CODE 4021005

4-INSTALLATION

ELECTRICAL INSTALLATION

Pass the electric cable coming out of the panel into the designed hole on the back of the stove.

The supply includes adhesive clips to be attached to the steel back so that the cable adheres to the back of the product, thanks to the

electric clamps, so that the cable does not remain dangling or cannot be inadvertently pulled.

Before securing the cable with clamps and clips, we recommend opening the panel (as in the operating position) to verify the necessary

elongation of the connection cable for the opening movement. Fix the clips and clamps with the panel in this position.

Don’t tighten the clamps or deform the cable, but let it slide slightly inside the clamp, leaving it a bit loose. The

clamp has the aesthetic purpose of not allowing the cable to protrude and not that of creating a block. In some

cases and/or appliances the cable might not even need to be xed, leaving it full freedom of movement

Remove the decorative panel according to the manual of the product on which the assembly is being carried out and connect the RJ11

plug (similar to a twisted pair cable) to the specic connector on the board (see picture).

The appliance can only be powered on when the mechanical and electrical installation has been performed.

4-INSTALLATION

101010

OPENING THE LIFT PANEL

To open the panel, gently press the top in the middle, where there is a notch, until you hear a short click. Move your hand away and the

internal gas piston will automatically lift the display.

CLOSING THE LIFT PANEL

To close the panel, proceed in the opposite order by gently pressing the middle of the display where there is a notch downwards, until the

recover position when you hear a second click indicating the mechanical locking of the piston.

The tutorial videos for installation of this accessory can be found on the website

4-INSTALLATION

1111

INSTALLATION OF RECESSED CONTROL PANEL CODE 4021001

The recessed control panel was built for all MAESTRO products, such as the inserts, which are mainly snapped into a decorative cladding.

This panel is compatible with any MAESTRO appliance.

MECHANICAL INSTALLATION

Install the recessed box of the MAESTRO panel into the wall or plasterboard using foam or fast setting cement like for standard electric

boxes, or, when installing on plasterboard, into the arranged holes to screw the metal box on an upright of the structure.

Bring an appropriately sized electric conduit from the appliance to the inside of the recessed box to pass the RJ11 plug of the connection

cable. It is recommended to use an electric conduit at least 20 mm large which corresponds to the size of the pre-perforations inside the

electric box of the panel

ELECTRICAL INSTALLATION

Pass the supplied electric cable into the conduit. The cable must not be more than 2 linear meters long.

The cable and/or conduit must never pass through areas in contact with the direct heat of the appliance or of the combustion chamber.

Connect the RJ11 plug (similar to a twisted pair cable) to the specic connector on the board (see picture) and on the display

PLEASE NOTE Inside the box secure a“coil” of cable with the provided clamp so that the display can be taken

out for updating.

4-INSTALLATION

121212

Snap the display onto the electric box, using the specic slots.

If you need to remove the display, press gently on the side of the display frame to release the internal lugs from their slots.

The tutorial videos for installation of this accessory can be found on the website

4-INSTALLATION

1313

INSTALLATION OF WALL MOUNTED CONTROL PANEL CODE 4021002

This panel is compatible with any MAESTRO appliance.

MECHANICAL INSTALLATION

Install the metal box containing the MAESTRO panel on the wall near the appliance using Ø 6 mm“Fischer”fasteners.

Bring the electric wiring of the panel from the appliance into the recessed box.

ELECTRICAL INSTALLATION

Connect the RJ11 plug (similar to a twisted pair cable) to the specic connector on the board (see picture) and on the display.

House the cable ush on the wall or appliance so that it is not inadvertently pulled

Snap the display onto the electric box, using the specic slots.

PLEASE NOTE Inside the box leave a“coil”of cable so that the display can be taken out for updating.

4-INSTALLATION

141414

If you need to remove the display, press gently on the side of the display frame to release the internal lugs from their slots, or use a pointed

instrument (even a paper clip) to press gently on the side holes making it easier to remove the lugs from their slots.

The tutorial videos for installation of this accessory can be found on the website

4-INSTALLATION

1515

KIT CODE 4021003  MAESTRO LIFT PANEL JAZZ HYDROMATIC 30 M1

By installing this accessory kit it is possible to manage the Maestro functions directly from the stove.

When the kit is purchased it is necessary to carry out the following operations:

• Remove the knockout hole“S”from the right hand panel at the back of the stove

• take the support“U”and fasten it to the stove panel (internally) with the two nuts“d”provided

• on the outer part snap t the plate with the board and rubber keypad“V”

• at this point connect the cable on the board (position 11) and on the Maestro“Lift”control panel

The panel is reversible and therefore it can also be installed on the left.

5-OPERATION

161616

FOREWORD

When the appliance is powered, the display lights up and it is updated with all the operating and product status information, contained

in the motherboard.

Wait approximately 15-20 seconds to get all the information before touching the keys.

After this waiting time, the panel will be perfectly operational.

The basic structure of the menus is very similar to that of the APP on the smartphone, present in the Android and iOS stores.This is to allow

the user interface to be as similar as possible for those using both interfaces

Depending on the Software version (visible in the SETTINGS menu) there can be two types of screens, though their operation is the same.

SCREEN WITH SOFTWARE VERSIONS 1.0.1 TO 1.0.7

SCREEN WITH SOFTWARE VERSIONS 1.0.8 TO 1.0.10

3 2

5-OPERATION

1717

DISPLAY’S EXTERNAL APPEARANCE

1Display

ON/OFF key

HOME key (to go back to the main screen)

4Browsing key of screens to the right

5Browsing key of screens to the left

6Increase values edit key

7Decrease values edit key

8OK key to conrm selection in the menus

SWITCHING ON/OFF

Press the ON/OFF key for a few seconds.

A beep will show that the on or o command is accepted

5-OPERATION

181818

Depending on the software version, dierences can be seen on the HOME page.

In more recent software versions, the menu can already be seen on the left side on the HOME page.

1 General status bar indicating time and temperature

2 Menu bar or current screen

3 Control window

4 Product status bar

5 Side bar of icons and active functions/menu

HOME SCREEN

The HOME screen displays the operating mode of the product and the point of return when the HOME key is pressed

In software versions 1.0.1-1.0.7, the MENU is accessed by pressing keys 4 and 5 while the OK KEY must be pressed to

enter the operating mode followed by keys 4 and 5 to select the function.

In software versions 1.0.8-1.10, the menu is already available on the HOME page, where you may scroll with keys 6/7 and

conrm by pressing OK.

5-OPERATION

1919

The menus are:

• MODE

• POWER

• FAN

• CHRONO

• ECO STOP

• MENU

The selected mode (MANUAL/POWER/COMFORT/OVERNIGHT/DYNAMIC) is indicated below the stove pictogram. A ame appears when

the stove is on.

In this version, keys 4 and 5 are only used to scroll to enter the password and to select the fans.

To activate the SILENT function, scroll with keys until you reach the MENU item, conrm by pressing OK, scroll with the arrows

until you reach SILENT MODE, press OK and select ON or OFF.

SILENT

6 - OPERATING MODE

202020

Maestro technology allows the heater to express its utmost potential with even an easier and more intuitive use. A real integrated micro-

computer communicates with your smartphone and further improves the performance of the heater that continues to work perfectly

even in non-ideal conditions.

The available settings are:

COMFORT Ideal for all situations requiring maximum comfort. In this mode the stove allows an optimised consumption of the fuel to

guarantee a good heating capacity and the best possible silent operation. Once this mode is activated, the user only has to choose the

desired temperature and the appliance will independently manage the ame and ventilation power to ensure maximum comfort. In fact,

in this mode it is not possible to change the power and ventilation, managed intelligently by the MAESTRO system.

DYNAMIC If you prefer traditional automatic operation with the option of setting the temperature and ventilation.

OVERNIGHTGuaranteesthe maximumsilencepossible(noise reducedupto4 times)allowingthemaintenanceofthe roomtemperature.

This mode is designed, in fact, for night-time operation or temperature conservation in an already pre-heated room ensuring the lowest

possible acoustic impact. In Overnight mode consumption and ventilation are managed intelligently by the MAESTRO system and for this

reason it is not possible to change its values.

MANUAL For those who prefer to use the product in the traditional manner without any temperature control. In this mode the user can

freely choose the mix of ame power and ventilation regardless of consumption or silence.

POWEROperationat maximum powerexpressedby the product for a limited time (20min) in orderto allow rapidheating of a coldroom.

For the expected performance and consumption in this mode, this function can be reactivated only once every hour.

Quiet operation * Comfort** Heating capacity Reduced consumption

COMFORT

OVERNIGHT

POWER

DYNAMIC

MANUAL

* In operation, during start-up and shutdown

** Gradual heat emission, glass cleaning and combustion chamber cleaning

This manual suits for next models

Table of contents

Languages:

Other MCZ Control Panel manuals

MCZ

MCZ 4018002 User manual

Popular Control Panel manuals by other brands

DeDietrich

DeDietrich IniControl Installation, user and service manual

Chamberlain

Chamberlain 378LM quick start guide

Cooper Menvier

Cooper Menvier Scantronic 9751 user guide

Belden

Belden Miranda iMC-Panel-200 Operator's guide

Polaroid

Polaroid Polaview 3000 Repair manual

Beijer Electronics

Beijer Electronics X2 control user guide

GE ATS4000 Quick programming guide

Videofied

Videofied XV-iP 210 installation manual

Ness

Ness D-8 installation manual

LynTec

LynTec RPC quick start guide

Honeywell

Honeywell MiniZone EMM-3U Product data

ETHINK

ETHINK KL8-3A Installation & user manual

Bosch

Bosch CC488 Quick reference guide

CAME

CAME ZL22N installation manual

RabbitCore

RabbitCore eDisplay OP7200 user manual

Panasonic

Panasonic AY-RP500 installation manual

Spectra

Spectra 1725 Reference & installation manual

Beijer Electronics

Beijer Electronics T15B installation manual

MCZ MAESTRO 4021004 User manual

Popular Control Panel manuals by other brands