MD SPORTS 1439021 User manual

MODEL: 1439021
VM Innovations
ASSEMBLY INSTRUCTIONS
TM
Register Now on themdsports.com and Earn a One-Year Warranty for Free!
Please contact us before returning the product to the store.

Give Us Your Opinion and Receive A
FREE FULL YEAR
EXTENTED WARRANTY!
Write a review for a recently
purchased item on
TheMDSports.com and receive an
extended full year limited warranty,
valued at $150.00.
See TheMDSports.com
for additional details.
TM

This product is covered by a limited warranty that is effective for 90 days from the date of purchase. If,
during the limited warranty period, a part is found to be defective or broken, we will offer replacement parts
at no cost to you, the customer. The only exceptions to the warranty include main frames, table tops,
playing surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper usage, alteration, misuse, abuse,
accidental damage or neglect.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from
one State (province) to another.
A PURCHASE RECEIPT (or other proof of purchase date) will be required before any warranty service is
initiated. For all requests for warranty service, please feel free to contact our Consumer Service Department
at :
Please be aware of your product’s Limited Warranty for the return/refund policy from the store, We, at Medal
Sports, can not handle the product which is out of product’s limited warranty since we only provide available
parts. Thank you!
PLEASE CONTACT US BEFORE RETURNING
THE PRODUCT TO THE STORE.
WEBSITE: www.themdsports.com
NOTICE!
STAPLE YOUR RECEIPT HERE
1 - Please leave your name, address, phone number, model number, parts needed on the answering
machine if there is no attendance. Failure to do so will result in a delay in shipping parts to you.
2 - Please review the replacement parts list and make sure that you have all of your parts before
beginning assembly. For questions that may arise or for missing/damaged parts, please contact us.
3 - Since you build all tables upside down, please inspect tabletops or playing surfaces right away before
putting together, all damaged table tops/playing surfaces need to be returned to the store. Please
contact with retailer for their return policy.
LIMITED 90 DAYS WARRANTY
www.themdsports.com
1439021 1
(Continued on the next page.)

X 4
Strong Adults Needed No Children in
Assembly Area
Keep away from pets Do not use or keep product
outdoors. For indoor use only.
No wet/humid conditions.
Power Tools
- Set Low Torque
High Torque
over tightened
TOOLS REQUIRED:
Phillips Screwdriver - Not Included
Standard (Flat Head Screwdriver) - Not Included
Wrench - Included
Allen Key - Included
CAUTION !
Electric Screwdrivers may be helpful during assembly;
however, please set a low torque and use extreme
caution.
WARNING:
CHOKING HAZARD -- This item contains small parts or / and small balls.
Not suitable for children under 3 years.
!
WARNING: Adult Assembly Required.
!
ASSEMBLY TIPS:
1 - Please read the instructions carefully, and follow all assembly, operation and safety instructions
properly in order to avoid damage or injury. For the assembly, at least four adults are required.
2 - Some figures or drawings may not look exactly like your product. Please read and understand the text before
beginning each assembly step.
1 - This product is intended for INDOOR use only.
2 - Please do not sit, climb or lean on the product.
3 - Please do not drag the product when moving it in order to avoid damaging the legs.
4 - Please only use furniture polish spray to clean the exterior surfaces of the product.
5 - This is not a child's toy, adult supervision is required for children playing this game.
IMPORTANT NOTICE!
www.themdsports.com
1439021 2
(Continued on the next page.)

1439021 PARTS LIST
2 3 41
x1 x4 x4 x4
6 7 85
x4 x4 x4 x4
10 11 129
x2 x2 x2 x2
14 15 1613
x4 x4 x2 x8
18 19 2017
x4 x1 x16 x16
22 23 2421
x14 x16 x13 x20
26 27 2825
x8 x16 x16 x4
30 31 3229
x4 x18 x4 x2
Mainframe Inside Leg - A Inside Leg - B Leg Base
Plastic Leg - A Plastic Leg - B Plastic Leg - C Plastic Leg - D
Side Top Board Lower Side Apron End Top Board Lower End Apron
Corner Brace Leg Top Panel Support Board
“U” Plastic Bracket
Steel Bracket
F4 x 1-1/2” Screw P3 x 1/2” Screw T4 x 1/2” Screw T4 x 5/8” Screw
F3 x 5/8” Screw 5/16” x 1” Bolt 5/16” x 1/2” Bolt 1/4” x 1-1/2” Bolt
1/4” Nut 1/4” x 1” Bolt 1/4” Washer 57” Cue
Glue 5/16” x 1-1/2” Bolt 5/16” Washer
www.themdsports.com
1439021 3
(Continued on the next page.)

P1 P2
x2 x4 x2
P3
34 35 3633
x1 x1 x2 x1
38 39 4037
x1 x1 x4 x40
42 43 4441
x4 x1 x1 x2
4645
x1 x1
Cue Rack Hook Cue Holder
Triangle Holder
2-1/4” Billiard Ball 2-1/4” Triangle Chalk Brush
Wrench Allen Key Leg Leveler F4 x 1-3/4” Screw
F3 x 1/2” Screw Cue Rack - Left Side Cue Rack - Right Side Cue Rack - Middle Shelf
Cue Rack - Top Panel
49
x1
Cue Rack - Base Panel
47
x2
48
x2
Adjustable "L" Bracket Corner Pocket Side Pocket
P4
x32
5/16” T - Nut
1439021 PARTS LIST
1439021 PRE-INSTALLED PARTS
ASSEMBLY INSTRUCTIONS:
1. Find a clean, level place to begin the assembly of your Billiard Table. The table will be assembled upside down
and then turned over on its legs once the assembly completed. This game table is heavy, and turning it over will
require at least four strong adults.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the parts list pages.
Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface.
www.themdsports.com
1439021 4
(Continued on the next page.)

FIG.1
3. Attach the Inside Legs - B (#3) to the Inside Legs - A(#2) using four Screws (#40) per Inside Leg - B. See FIG. 1.
4. Attach the Steel Brackets (#16) to the legs using two Bolts (#26) per Leg. See FIG. 1.
FIG.2
5. Attach the Leg Bases (#4) to the grooves using two Screws (#40) per Leg Base. See FIG. 2.
Note: Do not place the wrong surface of the Leg Base (#4) when you assemble the Leg Leveler (#39).
6. Screw the Leg Levelers (#39) into the Leg Bases (#4).
16
26
2
3
40
FIG. 2
X 4
X 8
X 4
4
39
40
X 4
X 8
X 16
X 16
X 4
2
3
16
26
40
FIG. 1
39
4
40
www.themdsports.com
1439021 5
(Continued on the next page.)

X 4
X 4
X 4
X 4
5
6
7
8
X 16
22
FIG.4
9. Attach the Plastic Legs (#5 & #6) to the Inside Legs (#2 & #3) and then place another Plastic Legs (#7 & #8)
around the other side. See FIG. 4.
10. Align the holes of the Plastic Legs (#5 & #6, #7 & #8), then attach legs together using four Screws (#22) per Leg.
Note: it is not recommended to use a power screwdriver when assembling the Plastic Legs.
Over - tightening ofthe screw can cause damage to the leg.
FIG. 4
22
7 8
and
2 3
and
5 6
and
FIG.3
7. Carefully align the seams of the Plastic Legs - A (#5)and Plastic Legs - B (#6), lock them using locking pieces
on the legs. Note: Listen to the sound of “click” when locking the legs together to ensure the legs are
locked firmly.
8. Next, lock the Plastic Legs - C (#7) and Plastic Legs - D (#8) together in the same way. See FIG. 3.
56
Locking piece
87
Locking piece
FIG. 3
www.themdsports.com
1439021 6
(Continued on the next page.)

X 8
23
X 2
X 2
X 2
9
10
11
X 2
12
X 1
18
X 14
X 16
21
P4
FIG.5
11. Tighten the pre - assembled Legs using two screws (#23) per Leg. See FIG. 5.
FIG.6
12. Apply the Glue (#18) in the grooves of the Side and End Top Boards (#9 & #11). See FIG. 6A.
13. Attach the Side Top Boards (#9) to the Lower Side Aprons (#10) using four Screws (#21) per Side Top Board.
14. Attach the End Top Boards (#11) to the Lower End Aprons (#12) using three Screws (#21) per End Top Board.
FIG. 5
FIG. 6
23
FIG. 6A
9
18
11
21
12
11
P4
10
21
9
www.themdsports.com
1439021 7
(Continued on the next page.)
P4

X 4
X 16
X 4
14
13
19
X 16
20
X 8
25
X 16
27
X 16
P4
FIG.8
17. Attach the pre-assembled Legs to the aprons using four Bolts (#27) per leg.
FIG. 7
FIG. 8
25
14
14
13
19
20
12 10
11 9
27
P4
FIG.7
15. Align the Lower Side Aprons (#10) and Lower EndAprons (#12) with Top Boards (See FIG. 6) as shown
in FIG. 7. And attach Corner Braces (#13) using fourBolts (#19) and four Washers (#20) per corner brace.
16. Attach the Leg Top Panels (#14) to the corners of the aprons using two Screws (#25) per Leg Top Panel.
www.themdsports.com
1439021 8
(Continued on the next page.)
P4

X 4
X 4
X 2
17
15
28
X 4
29
X 4
31
X 16
X 2
24
P1
FIG.10
19. Lift the pre-assembled Lower Aprons & Legs (SeeFIG.8) from the floor with four strong adults, turn it over,
and set table on its legs in the location where you play.
20. Place the Support Boards (#15) between the Lower Side Aprons (#10) as shown in FIG.10. Attach the
“U” Brackets (#17) to the Lower Side Aprons (#10) using four Screws (#24) per “U” Bracket. Please note
that “L” Brackets (#P1) & Support Board (#15) are parallel as shown in FIG. 10A.
P1
28
17
31
29
15
FIG. 9
FIG. 10
P1
P1
24
10
17
10
15
15
15
FIG. 10A
FIG.9
18. Attach the “U” Plastic Brackets (#17) to the Support Boards (#15) using one Bolt (#28), one Washer (#31)
and one Nut (#29) per “U” Bracket.
DO NOT LEAN THE
TABLE ON ITS LEGS
HOLD TABLE
HOLD TABLE DO NOT HOLD THE LEGS
CAUTION: Four strong adults are recommended to turn the table over as shown.
1. Lift the table off the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.
www.themdsports.com
1439021 9
(Continued on the next page.)

Go back and make sure that all connections are tight.
X 4
X 18
X 1
1
24
30
FIG. 11
24
FIG. 11B
FIG. 11A
10
30
11
1
1
1
12
12
11
15
10
9
1
9
15
P1
FIG.11
21. Place the Mainframe (#1) on the top of the pre-assembled Lower Table (See FIG. 10). Underneath the
Mainframe (#1), assemble the Mainframe (#1) to the Side & End Top Boards using eighteen Bolts (#30).
See FIG.11 & 11A.
22. Attach the Adjustable "L" Bracket (#P1) to the backside of the Mainframe (#1) using two Screws (#24)
per “L” Brackets (#P1). See FIG.11B.
www.themdsports.com
1439021 10
(Continued on the next page.)

X 1
X 4
X 2
37
P2
P3
FIG. 12
P2
P3
37
FIG. 12B
P1
37
FIG. 12A
P1
NOTE: DO NOT lift the table by the
pockets. If you move the table, do not
lift it by placing your hands beneath
the pockets and do not lean or put
pressure on them. Do not lean or sit
on the end or side rails as this may
damage the table.
FIG.12
23. Under the Mainframe (#1), adjust the "L" Bracket (#P1) in order to level the playfield of the Mainframe (#1).
See FIG.12A &12B.
www.themdsports.com
1439021 11
(Continued on the next page.)

X 16
X 4
X 5
40
23
41
X 1
42
X 1
43
X 2
44
X 1
45
X 1
46
X 2
47
X 2
48
X 1
49
FIG. 13
40
40
42
43
44
FIG. 13A
40
40
40
23
23
41
41
45
46
47
47
48
48 49
FIG. 13B
www.themdsports.com
1439021 12
(Continued on the next page.)

YOU ARE NOW READY TO PLAY!
FIG.13
24. Attach the Cue Rack - Middle Shelves (#44) to the Cue Rack - Left Side (#42) and Cue Rack - Right
Side (#43) using four Screws (#40) per Side. See FIG. 13A.
25. Attach the Cue Rack - Base Panel (#46) to the Cue Rack - Left Side (#42) and Cue Rack - Right
Side (#43) using four Screws (#40). See FIG. 13B.
26. Attach the Cue Rack Hooks (#47) to the Cue Rack - Top Panel (#45) using two Screws (#23) per
Hook. See FIG. 13B
27. Attach the Cue Holders (#48) to the Cue Rack - Top Panel (#45) using two Screws (#41) per Holder.
See FIG. 13B
28. Attach the Triangle Holder (#49) to the Cue Rack - Top Panel (#45) using one Screw (#23).
See FIG. 13B
29. Attach the Cue Rack - Top Panel (#45) to the Cue Rack - Left Side (#42) and Cue Rack - Right Side
(#43) using four Screws (#40). See FIG. 13B
www.themdsports.com
1439021 13
(The last page.)