Meanwell A301-OOW User manual

Pure Sine Wave Power Inverter
600W I 1 OOOW I 1500W
Technical data Rectifying faults
A If you have detailed questions on the specifications of the
V inverter please contact us.
Item number
Rated input voltage
Constant output power
Peak output power
(a max. of 15 min.)
Maximum input current
Output voltage 115VAC
230VAC
Output frequency
Idle current 115VAC
Consumption 230VAC
Input voltage range
Low voltage alarm
Lowvoltage shutdown
Efficiency
up to
Dimensions (mm)
Weight
A301~OOW
A301-1000W
12 V
DC 24 V DC 12 V DC
I 24 V
DC
600W
1000 W
1000 W
2000W
(650 W) (1200W)
70 A 40 A 100 A 50 A
115VAC +/- 3%
230VAC +/- 3%
50 Hz or 60Hz
to be specified
O. 85A O. 45A 1.8 A 1.8A
1.4A
1A
1A 1A
10.
7V-15V 21.4V-30V 10 .7 V-15V
21.4 V-3~ V
< 10.7 V < 21.4 V < 10.7 V < 21.4V
< 10 V < 20 V < 10 V < 20 V
85 %
335 x 236 x
83
395 x 236 x 83
3kg 4 kg
Item number A301-1500W I
Rated input voltage 12 V DC
24 V DC
Constant output power 1500W
I
Peak output power 3000W
a mal<'. of 10 min.l (1800 W)
Maximum input current 200 A 100 A
Output voltage 115VAC 115VAC
+/- 3%
I
230VAC 230VAC
+/- 3% I
Output frequency
50 Hz or 60Hz to be specified
Idle current 115VAC 1A 0.8A
Consumption 230VAC 2A 1.5A
Input voltage range 10.
7V-15V 21.4V-30V
Lowvoltage alarm < 10 .7 V < 21.4 V
Low voltage shutdown <
10 V < 20 V
Efficiency
up to 85 %
Dimensions (mm 415 x 283 x 100
Weight 5. 75 kg
Fault Cause Remedy
No output voltege, LED not
Illuminated Bad connection between bat- tery and inverter.
Internal fuses defect.
Check the cables and contact
In this case send the unit
back
to supplier.
No output voltageOVER-
The inverter has been over- Switch offthe inverter and the
TEMP LED illuminates heated. . power consuming units.
Wait for approx. 5
-10 min-
Utes and switch
on the
inverter only.
Reduce the loading and
ensure a better ventilation for the
inverter.
Then switch back
on the
consuming unit.
Overload LED illuminates Current consumption of the
consuming unit
is too high.
Possibly, there
is a short cir-
cuit
in the consuming unit.
Switch offthe inverter and
disconnect the consuming
units.
switch back on the inverter
only.
Ifthe OVERLOAD LED
is off, there is a short circuit at
the consuming unit or the
total load was higher than the
performance specified within
the technical data table.
Check the connecting cable
ofthe consuming unit for
mechanical damages.
Acoustic signal
in case of
loading
-
Battery voltage too low. In
case of loading battery voltage
falls below 10.7 V resp.
21.4
V.
The battery must be recharged.

1
3
Make sure that the place is well ventilated. If
installed into housing, ensure proper ventilation.
At least, keep a free space
of 10 cm around the
inverter.
Installing the inverter can be set horizontal or
vertical.
The air intake at the bottom
of the inverter
and the air outlet
on the back may not be
blocked.
In case of ambient temperatures of more
than 35°C (e.g. engine or heat ing rooms,
direct sunlight), the inverter will switch off
automatically, because ofthe activated self
heating feature.
2 Lay the flexible connecting cable (plus and minus)
from the battery to the connecting poles of the
inverter.
ill
Warningl
Make sure that the poles will not be
exchanged! Reverse polarity connection
will blowthe internal fuses. Exchange of
fuses
by experts only!
4 Fisrt connect the negative cable
to the white
negative terminal.Connect the positive cable to
the red positive terminal.
5 I 1:\ Warningl
~ In order for the integrated residual current-operated
protective device
of the 150S-12NE and 150S-24NE
inverters to work properly, the earth connection
of the
inverter must be electrically connected
to the chassis
of the vehicle or boat.
Lay the flexible earth cable from the earthing point
of the
vehicle to the earthing point of the inverter.
Connect the earth cable to the chassis terminal.
1:\ Warning!
~ Reverse polarity connection of the battery wires can
damage the inverter.
Do not use the inverter with
electrical systems using pos itive ground.
6 $
I
ON
WJW POWOR INV EICTER
[illF~ , @~
OfT
o
$
ON/OFF SW I civertemp output socket
overload
CAUTION:
*Always olace the inverter in
an
environment which is :
(A) Well ventilted
(8) Not exposed to direct
sunlight
or heat source
(C) Out of reach from children
(0) Away from water/moisture,
oil
or grease
(E)
Away from any flammable
substance