Medalab PLASMATROHN User manual

20
20
U S E R M A N U A L
PLASMATROHN
R E V I E W E D J U N . 2 0 2 1
Medalab Research S.L. www.medalab.com

USB - input for programming the
Plasmatrohn. (Not for end-user use.)
Service - for service purposes only
POWER - main switch
Top
Down
V - voltmeter (informative)
D E S C R I P T I O N O F T H E
D E V I C E
Plasma Generator
C O N S I D E R A T I O N S
The PLASMATROHN plasma generator is not
designed to cure any disease. It is not a
substitute for medical care, and is not a medical
device.
Neither the manufacturer nor the distributors
are responsible for any uses of the Plasmatrohn
generator other than those stated.
I N T R O D U C T I O N
People with pacemakers should not be
exposed to the effects of Plasmatrohn.
The plasma generator is designed for
laboratory work - verification of the effects
of frequencies on living microorganisms
(parasites, bacteria, viruses, fungi, prions,
microzymes etc. ....) or as an aid in
therapeutic treatment.
W A R N I N G S
M E D A L A B R E S E A R C H S . L . • T O D O S L O S D E R E C H O S R E S E R V A D O S • 2 0 2 0
Left
A - ammeter (informative)
Right
Enter - confirm

The Plasmatrohn is equipped with an integrated
frequency generator from 1 Hz to 900 kHz. Within
this range, frequency programs have been
established that have effects on a large number of
microorganisms and various pathologies.
The Plasmatrohn generator operates from a
frequency of 1 Hz - where the complete ignition of
the gases inside the tube takes place - and at about
5 Hz - where the appearance of the visible plasma
discharge occurs. The maximum frequency that
the Plasmatrohn can transmit without distorting
the output signal is 900 kHz. It therefore works
within a very wide band, from 1 to 900,000 Hz.
The frequency generated by the Plasmatrohn is
transmitted through the optocoupler (which
converts the electrical signal into light) to the
potential section of the generator, which in turn
transforms this frequency into a high voltage that
ignites the gas mixture inside the plasma tube.
The ignition of the gases in the tube creates the
plasma, which propagates these frequencies
contactlessly within 1 to 4 m of the generator, the
ideal distance where the person who is to receive
the treatment should be placed. Therefore, all
individuals present in that environment would be
benefiting from the emitted frequencies.
D E S C R I P T I O N
M E D A L A B R E S E A R C H S . L . • A L L R I G H T S R E S E R V E D • 2 0 2 1
Connect the 230 V cable to the device, at the
socket on the back of the device.
The two circuit breakers on the back of the
device must be in the on position - circuit
breaker levers up.
Connect the device to a 230 V outlet.
Start the device with the main "POWER"
button.
(The ambient temperature and the
temperature inside the device must be the
same - for example, if you have just brought
the device from a cool place, let it run for at
least 30 minutes "idle", i.e. without turning
on the generator, with only the fan on).
Manual mode - Press the "Enter" button.
Choose a preselection with the "Up" or
"Down" buttons.
Start the desired program with the "Enter"
button.
C O N T R O L L I N G A N D P O W E R I N G
U P T H E D E V I C E
The tube will turn on, and immediately start transmitting the required frequency to the
surroundings. On the display you will see the time countdown to the end of the program. During
this time, a mutual resonance (provided that the correct resonance frequency has been selected)
will occur between the receiving individual and the output frequency, which according to the
research of many scientists leads to its destruction of pathogens during a very short time. The
Plasmatrohn plasma generator makes it possible to verify these findings in a practical way. It was
developed on the basis of the findings of Dr. Royal Raymond Rife, Nikola Tesla, Dr. Hulda Regehr
Clark and other no less important scientists.
D O N O T T O U C H T H E P L A S M A T U B E D U R I N G O P E R A T I O N
Functioning
S T A R T - U P

Never wash the plasma tube with water or
detergents.
To clean it, use only a damp cloth, and only if the
device has been disconnected from the mains.
If you move the unit from a cool place to a place that is
at room temperature, wait at least 2 hours for the
temperature of the unit and the surrounding area to
equalize.
The plasma generator must be in
horizontal position!
Recommendations
Warranty
THE WARRANTY PERIOD FOR THE ELECTRONIC FUNCTION OF THE
GENERATOR IS 24 MONTHS FROM THE DATE OF SALE.
Certificate of conformity: The device complies with all applicable standards for devices
powered by the 230V/50Hz public network, in particular: EN 61326-1:06, EN 61000-3-
2-06, EN 61000-3-3-3-95+A1:01+A2:05. Tested at the Institute for Electrotechnical
Testing in Prague (state-owned company).
M E D A L A B R E S E A R C H S . L . • A L L R I G H T S R E S E R V E D • 2 0 2 1

LISTS OF
PROGRAMS AND
DISEASES