Medic Therapeutics 603-0082 User manual

TOTAL BODY WORKOUT SYSTEM
USER MANUAL

Review the user manual carefully prior to first use. To ensure proper product operation,
pay special attention to the safety precautions. Retain this user manual for further
reference.
SAFETY PRECAUTIONS
To avoid damage or injury to the user or third parties, read all instructions and safety
recommendations prior to use of this product. Continue to follow all instructions and
guidelines.
IMPORTANT NOTICES DURING OPERATION:
• Elderly or vulnerable people should consult their doctor before using the device, even
if there is no specific precondition for your health.
• If you experience pain or any abnormal sensations when using the device, stop use
immediately and consult your doctor.
• Use the device on a flat surface. If it is not placed on flat surface, the device will not be
stable, and could tip over resulting in injury.
• If the operation of the device begins to look abnormal, stop the exercise immediately.
• Always store in a cool, moisture-free area.
• Children and individuals with disabilities must not use the device without adult
supervision.
• To avoid accidents or injuries, do not allow children or pets get on the device.
• It should not be used by more than two people at the same time. To avoid accident or
injury, the device should not be used while holding a baby.
• If the device fails, consult your dealer or consult the section on Warranty of this
Manual.
• Do not use it for other means than those described in this manual.
2

PARTS LIST:
3
Base and chair
Part # 1
Quantity 1
Straight Rollers
Part # 8
Quantity 4
Bolt 8 * 85
Part # 15
Quantity 1
Screw M10 * 90 allen
Part # 22
Quantity 1
PP Screws
Part # 29
Quantity 2
Back Support
Part # 2
Quantity 1
Grips piece
Part # 9
Quantity 2
Bolt 8 * 45
Part # 16
Quantity 1
Screw M8 * 55 allen
Part # 23
Quantity 1
PP Nut
Part # 30
Quantity 2
Rear Leg
Part # 3
Quantity 1
Springs
Part # 10
Quantity 2
Bolt 8 * 55
Part # 17
Quantity 1
Hex Nut M8
Part # 24
Quantity 2
Pedals
Part # 31
Quantity 2
Connector
Part # 4
Quantity 1
Knobs
Part # 11
Quantity 2
Back support rollers (A)
Part # 18
Quantity 3
Bushing PP 12 * 27.5
Part # 25
Quantity 2
Washer 8 * 22 * 1.5
Part # 32
Quantity 2
Front Leg
Part # 5
Quantity 1
Caps 7
Part # 12
Quantity 3
Washer 8 * 19 * 1.5
Part # 19
Quantity 19
Bushing cover
Part # 26
Quantity 2
Insert bushing 12 * 86
Part # 33
Quantity 2
Neck support
Part # 6
Quantity 1
Hex Cap Nut M8
Part # 13
Quantity 4
Washer 10 * 20 * 1.5
Part # 20
Quantity 1
Screw M6 * 12
Part # 27
Quantity 2
Resistance Bands
Part # 34
Quantity 2
Backing Rollers
Part # 7
Quantity 3
Screw M8 * 45 allen
Part # 14
Quantity 1
Hex Nut M10
Part # 21
Quantity 1
Garters
Part # 28
Quantity 2
Reference Images
Parts List

4
EXPLODED-VIEW DRAWING

5
ASSEMBLING INSTRUCTIONS
Step 1
Attach the back support piece (# 2) to
the base piece and seat (# 1) in the holes
indicated with the dotted line of the
drawing using the screw (# 22), washer
(# 20) and nut (# 21) that are attached
to the base piece and seat (# 1) using
the 17mm (11/16”) wrench and the 5mm
(13/64”) Allen key.
Step 2
Attach the back leg piece (# 3) to the
base piece and seat (# 1) at the holes
marked with the dotted line of the
drawing. Take the screw (# 23), washer
(# 21) and nut (# 24) and place it on the
rear leg (# 3). Tighten the screw, washer
and nut by using the 13mm (1/2”)
wrench and 5mm (13/64”) Allen key.
Use the 8 * 55 bolt (# 17) that is
located in the lower hole of the rear leg
piece (# 3) to fix the piece in place in
active mode.
Step 3
Attach the connector piece (# 4) to the
base piece and seat (# 1). Once inside
insert the knob (#11) and slide it to align
the holes on the connector piece to the
knob.
These holes are used to be able to
change the length of the device
depending on the height of the user.
Simply pull the knob and adjust
connector piece to desired length.

6
Step 4
Place the front leg piece (# 5) in the
connector piece (# 4) in the holes indicated
with the dotted line. Using the screw (#14),
washer (#21) and nut (#24) and place them
in the base piece and seat (#1). Tighten the
screw, washer and nut by using the 13mm
(1/2”) wrench and a 5mm (13/64”) Allen key.
This hardware is inside the bag that you will
find inside the packaging.
Use the 8 * 55 bolt (#16) that comes inside
the bag that is inside the packaging to place
it in active mode.
Step 5
Insert the neck support piece (#6)
to the back support piece (#2). Once
inside, insert the knob (#12) and slide
the neck support part to align the holes
to the knob.
These holes are used to change the
height of the neck support depending
on the height of the user.
Step 6
Place the back roller pieces (#7), one in each
of the bushings found in the neck support
(#6) and back support (#2) pieces indicated
with the dotted line.
Next, put the back support rollers (# 20)
and at the end, place the caps (#13) on the
opposite end of the back roller parts (#7).
These caps come inside the bag that you will
find inside the packaging.

7
Step 7
Insert the straight roller pieces (#9)
into the horizontal tubes of the
front leg (# 5) indicated with the
dotted line. Next, place the grip
pieces (#10) on the horizontal tubes
of the front leg piece (#5) marked
with the dotted line.
Cardio system assembly
All the parts required to set up the cardio system are inside
the box in the packaging.
Step 8
Place the bushing (#33) in the
hole marked with the dotted line
on the front leg (#5). Next, insert
the bushing piece (#25) into the
bushing insert (# 33) followed by
the rubber bands (#28) on the side
with round holes. Finally, using
the hub cover piece (#26) and the
screw (#27) fix them using the 5mm
(13/64”) Allen key.
Make sure to place each of the parts
mentioned in the previous step
in the correct order in which it is
specified in the drawing, using the
dotted line for reference.

8
Step 9
Insert the pedals (#31) into the threaded
studs from where you previously removed
the horizontal tubes attached to the
middle of the front leg (# 5). Using the
washers (#32) and nuts (#13) fix them by
tightening them with the wrench. Finally,
place the straight rollers (#8) in the
horizontal tubes located on the upper part
of the pedals (#31).
Make sure to place each of the parts
mentioned in the previous step in the
correct order in which it is specified in
the drawing, using the dotted line for
reference.
Step 10
Using the PP nut (#30) and the PP
screw (# 29) attach the band piece (#
28) to the pedal piece (#31).
Step 11
Remove the nuts (#13) found on the
horizontal bolts of the middle part of the
rear leg (# 3) and place the 2 springs (#10)
from its lower end.

9
HOW TO USE
Adjust the level of back support assistance.
• To adjust the level of assistance it is necessary
to place or remove the springs, only the upper
part, identified by a hook that attaches to the
bolts sides that are at the bottom of the back
leg support (# 3)
• It is necessary to modify this assistance
depending on the weight and physical capacity
of the user.
Back support position adjustment.
Total Body Workout System has 4 options for placing the back support
• The Total Body Workout System has 4 options for placing the back support.
• ABS mode: Depending on the amount of springs used, that will be the assisted
resistance the user will get without being fixed with the 8 * 85 bolt part (#17).
• Abdominal bench mode: Place the back support in a position parallel to the ground and
fix it by inserting the 8 * 85 bolt (# 17) crossing it through the hole indicated with the
dotted line. It is recommended that no springs be attached for easy placement.
• Fixed mode: Position the back support vertically by inserting the 8 * 85 bolt (# 17)
crossing it through the hole marked with the dotted line. It is recommended that no
springs be attached for an easier setup.
• Folding mode: Remove pin 8 * 85 (# 17) and make sure that no spring is attached.

10
Resistance adjustment in cardio system
• The Total Body Workout System has 3 levels of resistance in its cardio system to be
used depending of the physical capabilities of the user.
• To be able to modify the resistance level, loosen the PP nut, change the level and
tighten again.
• Level 1 higher resistance, Level 3 lower resistance.
Resistance band placement
• The Total Body Workout System has
2 resistance bands to work the upper
body, back, shoulder, biceps, triceps
and arms.
• Attach the resistance bands from
their lower end to the front or rear leg
depending on the exercise to perform.
• Secure the level of the resistance band
to the leg correctly to prevent the leg
from coming loose during workouts.

11
WARRANTY:
Limited Lifetime Warranty
Your Medic Therapeutics Total Body Workout System is backed by a limited lifetime
manufacturer’s warranty. Medic Therapeutics will repair or replace your device at any
time should it fail due to a defect in material or workmanship, subject to the certain
limitations.
This limited warranty does not cover any damage that results from unauthorized
or improper use, service, or repair. Further, it does not cover damage caused by
accident, impact, negligence, or normal wear and tear. Should you discover your Medic
Therapeutics Total Body Workout System is not functioning properly, please send your
device to our repair center for evaluation. If your product cannot be repaired or serviced,
we will reserve the right to change it for a similar or newer model.
Please note that a flat rate of $60.00 will be charged to cover a service evaluation fee
and return shipping of your device. All warranty claims must be accompanied by a copy
of your proof of purchase from an authorized retailer. Please send your device, proof
of purchase, and a check or money order in the amount of $60.00 made out to Medic
Therapeutics to:
Address:
Medic Therapeutics Service Center
3069 Taft Street
Hollywood, FL 33009
Contact:
[email protected]om