Medion Akoya P340 series User manual

12.5“ Tablet with Keyboard
Instruction Manual

2
Table of Content
1. About these Instructions............................................................................. 4
1.1. Symbols and Key words used in these Instructions................................... 4
1.2. Proper Use ................................................................................................................. 5
2. Declaration of Conformity .......................................................................... 5
3. Information on trademarks ........................................................................ 6
4. Safety Instructions....................................................................................... 6
4.1. Dangers for children and people with reduced ability to operate
electronics ................................................................................................................. 6
4.2. Operational Safety.................................................................................................. 7
4.3. Never carry out repairs yourself ........................................................................ 8
4.4. Data backup.............................................................................................................. 8
4.5. Setup Location (in Notebook Mode) ............................................................... 9
4.6. Environmental Requirements ............................................................................ 9
4.7. Ergonomics .............................................................................................................10
4.8. Connecting..............................................................................................................11
4.9. Cabling......................................................................................................................12
4.10. Information about the Touchpad....................................................................13
4.11. Notes on the Battery............................................................................................14
4.12. Protecting the Display ........................................................................................15
5. Included with your Device ........................................................................ 16
6. Views........................................................................................................... 17
6.2. Left Side....................................................................................................................18
6.3. Right Side.................................................................................................................18
7. About this Device....................................................................................... 19
7.1. Setting up the Stand............................................................................................19
7.2. Using the Device in Notebook Mode ............................................................20
7.3. Separating the Tablet Unit and the Keyboard ...........................................21
7.4. Using the Device in Tablet Mode ....................................................................21
8. Preparation for Starting-Up...................................................................... 22
9. Power Supply ............................................................................................. 22
9.1. On/Off Switch.........................................................................................................22
9.2. Mains Power ...........................................................................................................23
9.3. General handling of rechargeable batteries...............................................24
9.4. Battery Mode..........................................................................................................24
9.5. Power Management (Power Options)...........................................................25
10. Display ........................................................................................................ 26
10.1. Touch Screen ..........................................................................................................26
10.2. Connecting an External Monitor.....................................................................26
11. Data Input................................................................................................... 26
11.1. Specific Keys ...........................................................................................................26

3
11.2. Touchpad.................................................................................................................27
12. Sound System............................................................................................. 27
12.1. External Audio Connections .............................................................................27
13. Network Operation.................................................................................... 28
13.1. Wi-Fi (Wireless Network) ....................................................................................28
13.2. Bluetooth.................................................................................................................28
13.3. Airplane Mode .......................................................................................................29
14. microSD Card Reader................................................................................. 29
14.1. Inserting a Memory Card ...................................................................................29
14.2. Removing Memory Cards ..................................................................................29
15. USB Port ..................................................................................................... 30
16. Securing Your Device................................................................................. 30
16.1. Password Setting (Power-on) ...........................................................................30
17. Resetting the System to its Factory Settings........................................... 31
17.1. System Recovery with PowerRecover (optional).......................................31
17.2. System restore with Windows Recovery Options .....................................32
18. UEFI Configuration .................................................................................... 34
18.1. Executing the UEFI Configuration ..................................................................34
19. FAQs – Frequently Asked Questions......................................................... 35
20. Customer Service....................................................................................... 36
20.1. What To Do in Case of Hardware Problems ................................................36
20.2. Find the Cause ......................................................................................................36
20.3. Do You Need More Help?...................................................................................36
20.4. Driver Support .......................................................................................................36
20.5. Transport..................................................................................................................37
20.6. Maintenance...........................................................................................................37
21. Upgrading/Modifying and Repair ............................................................ 38
21.1. Notes for Service Technicians...........................................................................38
22. Recycling and Disposal.............................................................................. 38
23. European EN ISO 9241-307 Class II Standard .......................................... 39
24. Legal notice ................................................................................................ 41
25. Index ........................................................................................................... 42

4
1. About these Instructions
Before using the device for the first time, please read these operating
instructions carefully, paying special attention to the safety notices.
This device should only be used as designated and as described in these
instructions.
Please keep these instructions in a safe place for future reference.
Always include these instructions if selling or giving away the device.
1.1. Symbols and Key words used in these
Instructions
DANGER!
Warning of immediate risk of fatal injury!
WARNING!
Warning: possible mortal danger and/or serious
irreversible injuries!
WARNING!
Warning: danger due to excessive volume!
CAUTION!
Warning: possible light or moderate injuries!
PLEASE NOTE!
Please follow the guidelines to avoid property
damage.
Additional information on using the device.
PLEASE NOTE!
Please follow the guidelines in the operating
instructions.

5
1.2. Proper Use
This device is designed for the use, management and editing of electronic
documents and multimedia content, as well as for digital communication. The
device is intended for private use only and not for industrial/commercial use.
Please note that we shall not be liable in cases of improper use:
• Do not modify the device without our consent and do not use any auxiliary
equipment which we have not approved or supplied.
• Use only spare parts and accessories which we have supplied or approved.
• Follow all instructions in this manual, especially the safety information. Any
other use is deemed improper and can cause personal injury or damage to the
product.
• Do not use the device in areas where there is a risk of explosion such as tank
farms, fuel storage depots or areas in which solvents are processed.It is also not
permitted to use this device in those areas where the air is polluted with fine
particles (e.g. flour dust or sawdust).
• Do not use the device in extreme environmental conditions.
2. Declaration of Conformity
This product is supplied with the following wireless features:
• Wireless LAN
• Bluetooth
Medion AG hereby declares that this product conforms to the following European
requirements:
• R&TTE Directive 1999/5/EC
• Ecodesign Directive 2009/125/EC
• RoHS Directive 2011/65/EU
Should your device work with a network connection in the 5 GHz frequency range
of the inbuilt wireless LAN solution, then it can only be used inside buildings in all
EU countries.*
Full declarations of conformity are available at www.medion.com/conformity.
*In order to meet this requirement, you should not use channels 34-64 at your wireless LAN
access point.

6
3. Information on trademarks
Windows® is a registered trademark of Microsoft®. Intel, the Intel Logo, Intel Inside,
Intel Core, device, and Core Inside are trademarks of Intel Corporation in the U.S.
and/or other countries.
®
, the HDMI logo and the name High-Definition Multimedia Interface are
registered trademarks of HDMI Licensing LLC.
Other trademarks are the property of their respective owners.
4. Safety Instructions
4.1. Dangers for children and people with reduced
ability to operate electronics
This device may be used by children over the age of 8 and by
persons with limited physical, sensory or mental abilities or by
those without experience and knowledge, if they are supervised
or have been instructed in the safe use of the device and
understand the ensuing dangers.
• Children should be supervised to ensure that they do not play
with the device.
• Cleaning and user maintenance must not be carried out by
children unless they are supervised.
• Keep the device and accessories out of reach of children.
DANGER!
Risk of suffocation!
Packaging film can be swallowed or used improperly.
Therefore, there is a risk of suffocation!
`Keep packaging material such as plastic film or
plastic bags away from children.

7
4.2. Operational Safety
Please read this section carefully and follow all instructions given.
The instructions will help you to operate the device reliably and
increase its service life.
• Never open the housing of the device, battery or AC adapter!
This could result in an electric shock or even ignite a fire which
will damage your device.
• Do not insert anything into the device through the slots and
openings. This could result in an electric shock or even ignite a
fire which will damage your device.
• The slots and openings on the device are for ventilation
purposes. Do not cover these openings as this could cause the
device to overheat.
• The device is not intended commercial or industrial use.
• To avoid damage from lightning strikes, do not operate the
device during thunderstorms.
• Do not place any objects on top of the device and do not
exert pressure on the display. Otherwise, there is a risk that the
display may break.
• If the screen breaks, there is a danger of injury. If this happens,
pick up the shattered pieces wearing protective gloves and
send them to your service centre for professional disposal.
Finally, wash your hands with soap, as the pieces may have
been contaminated with chemicals.
• The stand on the rear of the device should not be folded out
at an angle of more than 110°.
• Ensure that there are no pens or other objects between
the stand and the device when folding away the stand.
Otherwise, this may cause damage.
• In order to avoid any damage to the device, ensure that the
plug contacts do not come into contact with water under any
circumstances. If this should occur, it is imperative that the plug
contacts are dried thoroughly before the device is used again.

8
• To avoid damaging the screen, do not touch it with fingers or
sharp objects.
• Place the tablet unit carefully and centrally in the mounting
fixtures on the base unit to avoid damage.
• Should the below occur, switch the device off immediately/
do not switch the device on, disconnect the mains plug and
contact customer services if
−the AC adapter or the attached power cable or plug is
burnt or damaged. Replace faulty mains cables/mains
adaptors only with original parts. These parts should not
be repaired under any circumstances.
−the device housing is damaged or liquid has penetrated
into the device. Have the device inspected by customer
services. Otherwise, it may not be possible to operate the
device safely. There may be a risk of electric shock and/or
harmful laser radiation!
4.3. Never carry out repairs yourself
CAUTION!
Risk of electric shock!
There is a risk of electric shock if repairs are not carried
out by qualified personnel!
`Never try to open or repair the product yourself!
`In the event of a fault, please contact the Service
Centre or an approved repair specialist.
4.4. Data backup
PLEASE NOTE!
Back up your data to external storage media before
each update. We do not accept any liability for claims
for compensation arising from loss of data or any
consequential loss or damage.

9
4.5. Setup Location (in Notebook Mode)
• Keep your device and all connected devices away from
moisture and avoid dust, heat and direct sunlight.
Non-compliance with these instructions can lead to faults or
damage to the device.
• Do not use the device outdoors because external elements,
such as rain, snow, etc., could damage it.
• Set up and operate all components on a stable, level and
vibration-free surface to prevent the device from falling down.
• This device is not suitable for use with VDU workstations.
4.6. Environmental Requirements
• The device is most reliably operated at an ambient
temperature between 5°C (+41°F) and 30°C (+86°F) and
at a relative humidity between 20% and 80% (without
condensation).
• When powered off, the device can be stored at temperatures
between 0°C and 60°C (+32°F and 140°F).
• During a thunderstorm, unplug the AC adapter from the wall
outlet. For extra safety, we recommend using an overvoltage
protection device to prevent the device from sustaining
damage as a result of power surges or lightning strikes.
• After transporting the device, wait until the device has
reached room temperature before switching it on. Large
changes in temperature or fluctuations in humidity can cause
moisture build up within the device due to condensation. This
can cause an electrical short circuit.
• Keep the original packaging in the event the device needs to
be sent in for repairs.

10
4.7. Ergonomics
PLEASE NOTE!
Avoid dazzle, reflections and a light-dark contrast that
is too strong in order to protect your eyes.
The device should never be placed next to a window because
this is the brightest part of the room in daylight. This brightness
can make it more difficult for the eyes to adjust to the darker
display. The device should always be positioned so that the
direction of vision is parallel to the window front.
Setting up the device with your back to the window is incorrect
as reflections from the bright window on the screen will then be
unavoidable.
A position looking onto the window is also incorrect as the
contrast between the dark screen and the bright daylight can
cause problems for the eyes to adjust and result in problems.
The parallel line of vision should also be maintained in relation
to artificial lighting equipment.
In other words, the same criteria and principles apply where
the workspace is illuminated with artificial light. Where space
restrictions make it impossible to set up the screen as described,
then correct positioning (rotating, tilting) of the device/
screen can prevent dazzling, reflections and excessive bright-
dark contrast, etc. In many cases, an improvement can also
be achieved by using slats or vertical blinds on the windows,
partition walls or by changing the artificial lighting equipment.

11
4.8. Connecting
Follow the instructions below to connect your device correctly
and safely:
4.8.1. Power Supply
CAUTION!
Risk of electrical shock!
There are live components inside this AC adapter. In
the event of an unintentional short circuit of this AC
adapter, there is a risk of electrical shock or fire!
`Do not open the housing of the AC adapter.
• The wall wall must be close to the device and easily
accessible.
• To disconnect the power supply from your device (via the AC
adapter), pull the plug from the power outlet.
• Plug the device’s AC adapter into AC 100 – 240 V~ 50/60 Hz
earthed sockets only. If you are not sure about the power
supply at the set-up location, please ask your electricity
supplier.
• Only use this device and accompanying AC adapter with each
other.
• For extra safety, we recommend using an overvoltage
protection device (surge protector) to prevent your device
from sustaining damage as a result of power surges or
lightning strikes.
PLEASE NOTE!
Only use this device and accompanying AC adapter
with each other.

12
WARNING!
Impairment to hearing!
Listening through earphones or headphones at
excessive volume levels, as well as changes to the basic
settings of the equaliser, drivers, software or operating
system generates excessive acoustic pressure and can
lead to loss of hearing.
`Before pressing play, set the volume to the lowest
setting.
`Start playback and increase the volume to a
comfortable level.
4.9. Cabling
• Position the cables so that they cannot be stepped on or
might cause a risk for tripping.
• To avoid damaging the cables, do not place any objects on
them.
• Do not connect peripheral devices – such as keyboards,
mouse and monitor, etc. – when the device is switched on
to avoid damage to the device or the devices. Some devices
may also be connected while the computer is running. This
is generally the case for devices with a USB connection. In all
cases, observe the relevant operating instructions.
• Maintain a distance of at least one metre from sources of
high-frequency and magnetic interference (TV sets, speakers,
mobile phones, DECT telephones, etc.) in order to avoid
malfunctions and data loss.
• Please note that only shielded cables that are shorter than
3metres may be connected to the external interfaces of this
device.
• Do not exchange the supplied cable for another one. Use only
the supplied cable as this cable has been extensively tested in
our laboratory.

13
• In addition, when connecting your peripherals only use the
connecting cables supplied with those devices.
• Ensure that all connection cables are connected to their
corresponding peripheral device to avoid any interference
radiation. Disconnect any cables that are not required.
• The only devices which may be connected to the device are
those that meet the requirements set out in the EN60950
standard “Information Technology Equipment – Safety” or
devices that meet the EN60065 standard “Audio, video and
similar electronic apparatus – Safety requirements”.
4.10. Information about the Touchpad
• The touchpad is operated with the thumb or another finger
and reacts to the energy given out by the skin. Do not use
pens or other objects as these can damage your touchpad.
• Dust or grease on the touchpad can affect its sensitivity.
Remove the dust or grease from the surface of the touch pad
with a soft, dry and lint-free cloth.

14
4.11. Notes on the Battery
WARNING!
Risk of explosion!
There is a risk of explosion if the battery is replaced
incorrectly.
`Do not heat up the battery to a temperature greater
than the maximum ambient temperature stated.
`Never open the battery.
`Do not throw the battery into an open fire.
`Do not short-circuit the battery.
`Only replace with the same type of battery or with a
similar type recommended by the manufacturer.
`Dispose of used batteries in accordance with the
information provided by the manufacturer
To extend your battery’s performance and lifespan and ensure
safe operation, you should also observe the guidelines below:
• Avoid dirt and contact with electrically conductive materials
or chemical substances and cleaning agents.
• Use only the supplied AC adapter to charge the battery. Make
sure (via the device display or acoustic signal) that the battery
is fully discharged before charging it again.
• Do not remove the battery while the device is switched on or
data may be lost.
• Take care when storing the battery and when using the
device that the contacts on the battery and the device are not
soiled or damaged. This could cause malfunctions.
• Ensure the device is switched off before replacing the battery.
• If the battery is integrated into the device it cannot be readily
replaced by the user themselves. In this case the battery must
be replaced by a service technician.

15
4.12. Protecting the Display
The display is the most sensitive component part of the device
as it consists of thin glass. It can break if subjected to too much
stress.
• Do not scratch the cover of the device, because it will not be
possible to remove any scratches.
• Avoid contact between the display and hard objects (e.g.
buttons, wristwatch).
• Do not place any objects on the display.
• Do not allow any objects to drop onto the display.
• Do not pour any fluids into the device, as this could damage it.
• Do not scratch the display with your fingernails or hard
objects.
• Do not clean the display with chemical cleaning products.
• Clean the display with a soft, dry and lint-free cloth.
PLEASE NOTE!
The surfaces of the device are covered in protective film
to prevent scratching during production and transport.
Remove the film once the device has been set up
properly and before you use it.

16
5. Included with your Device
Please check that the contents are complete and notify us within 7 days of purchase
if any of the following components are missing:
• device (tablet unit with keyboard)
• AC Adapter
AC/DC Adapter FSP Group, FSP 045-REBN2
Required Voltage 100 - 240 V~ 50/60 Hz
AC Input 100 - 240 V~ 1,5A 50/60 Hz
DC Output 19 V 2,37 A
DANGER!
Risk of suffocation!
Packaging film can be swallowed or used improperly.
Therefore, there is a risk of suffocation!
`Keep packaging material such as plastic film or
plastic bags away from children.

17
6. Views
6.1. Open Device
1
2
3
4
4
5
6
7
8

18
1) Webcam (Rear)
2) Webcam
3) Touchpanel
4) Speaker (Rear)
5) Connection contacts
6) Connection plug to the tablet unit
7) Keyboard
8) Touchpad
6.2. Left Side
109 11 12 13
9) Microphone
10) USB 3.0 / HDMI (type C) Port*
11) Power Socket
12) USB 3.0 Port (type A)
13) microSD Card Slot
6.3. Right Side
14 15 16 17
14) USB 2.0 Port
15) Audio combo (mic in & audio out)
16) Volume Buttons +/-
17) Power ON/OFF
* can be used as a HDMI connection via a HDMI / (type C) adapter
(the adapter is not supplied in the delivery)

19
7. About this Device
Thanks to its removable display, this device is designed for use in notebook mode
as well as tablet mode.
7.1. Setting up the Stand
There is a stand on the rear of the device that can be folded out as required.
`Carefully fold out the stand, as indicated by the arrow, until you have achieved
the desired angle.
(images similar)
PLEASE NOTE!
Risk of damage!
If the tablet unit is incorrectly connected to the base
unit, this may damage the contacts.
`Do not use excessive force when folding out the
stand to avoid damaging the hinges.
`The stand should not be folded out at an angle of
more than 110°. Ensure that there are no pens or
other objects between the stand and the device
when folding away the stand. Otherwise, this may
cause damage.

20
7.2. Using the Device in Notebook Mode
The tablet unit is transformed into a notebook thanks to the easy connection with
the keyboard.
`Hold the tablet unit securely with both hands and insert it into the centre of the
mounting fixture on the keyboard.
(image similar)
PLEASE NOTE!
The docking tongue between the tablet and the
keyboard is highly magnetic so that the connection
with the tablet can be achieved easily and securely.
`To ensure that the device is held in a stable position, fold out the stand on the
rear of the tablet unit (see Chapter Setting up the Stand).