Mee-go Milano+ User manual

Dear Customer,
Thank you for purchasing the Milano+ travel system.
For the safety of you child, you must read and follow these instructions
carefully.
This product has been manufactured under quality surveillance and been
tested to EN1888-2:2018 and BS EN1466:2014.
IMPORTANT- READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

User manual
Unfolding and folding the stroller frame
To unfold the frame, rst lie it at (1), then, holding the handle, pull it upwards
(2), until the locking mechanism engages (3).
ATTENTION! Before using the stroller ensure the locking mechanism is secured.
To fold the frame, press the buttons on both sides of the handle (4,5) and push
downwards.
ATTENTION! Before starting to fold the frame, remove the carrycot / seat, cup
holder and release the front swivel wheels. For a more compact fold also remove
the back wheels.
Adjusting the height of the handle
The height of the handle can be adjusted by simultaneously pressing the buttons
on both sides of the handle, and rotating it up or down (6).

Fitting and removal of rear wheels
To attach the rear wheels, press the metal button in the centre of the wheel (7),
then slide the wheel onto the axle, as far as it can go then pull back slightly.
To remove the rear wheels press the button to release, and pull wheel outwards.
Fitting and removal of front wheels
To install the front wheel, slide the wheel pin into the socket under the footrest of
the stroller until you hear the click (8).
ATTENTION! Before using the stroller make sure both wheels are properly mounted.
To remove the front wheel, press and hold the button to release the pin (9).
ATTENTION! Before using the stroller make sure both wheels are properly mounted.
Holding down the red button on the rear axle of the stroller (47), insert the axle
with the tapered side into the wheel axle housing. Release the button and pull on
the axle to make sure it is properly locked. Repeat the operation with the other
wheel. To disassemble the rear wheel, press the red button on the rear axle of the
stroller and pull out the wheel together with the axle. To remove the axles from
the wheels, press the button in the centre of the rim and pull out the axle from
the wheel.

Swivel front wheels
The stroller has swivelling front wheels. To lock the wheels rotate the knob (10), and
then rotate the opposite direction to unlock the wheels.
Applying the brake
To apply the rear wheel brake, step down on the brake pedal (11), to release
the brake lift up the brake pedal.
ATTENTION! When the stroller is stationary, always apply the brake.
ATTENTION! Do not leave the stroller with child on a sloped surface, even if the
brake is applied.
ATTENTION! Never push the stroller with the brake applied.
Suspension
The stroller is equipped with suspension springs use the switch to adjust the
hardness / softness of the ride (12).

Assembling and disassembling the carrycot
The carrycot can be mounted on the frame in a forward or rearward facing
position. To mount the carrycot on the stroller frame, insert the connectors into
the slots on each side of the frame and push downwards until you hear a“click”(13)
To remove the carrycot, press the buttons on each side of the carrycot and lift
the unit upwards (13).
NOTE: Do not fold the stroller frame with carrycot assembled.
ATTENTION! Before using the stroller make sure the carrycot is properly installed
and locked on both sides of the frame.
Adjusting the backrest
The carrycot backrest adjustment mechanism is located underneath the
carrycot. To raise the backrest press and turn the mechanism to the left, press
and turn the mechanism to the right to lower the backrest (14).
Carrycot canopy
The carrycot is equipped with a canopy, to change its position, simultaneously
press the buttons on both sides of the canopy and select the desired angle (15).

Ventilation
To increase ventilation in the carrycot unzip the zip on the back of the canopy
and the back of the carrycot (16)
Apron
Open the press studs on the sides of the apron to allow you to remove your child
from the carrycot without removing the whole cover (17)
Assembling and disassembling the seat unit
The seat unit can be mounted on the frame in a forward or rearward facing
position. To mount the seat on the stroller frame, insert the connectors into the
slots on each side of the frame and push downwards until you hear a “click” (18).
To remove the seat, press the buttons on each side of the carrycot and lift the
seat upwards (19).
ATTENTION! Before using the stroller make sure the seat is properly installed and
locked on both sides of the frame.
Adjusting of the backrest of the seat unit
The backrest can be adjusted into 4 positions by pressing the lever on the back of
the seat and adjust desired position (20,21).
ATTENTION!
Pay special attention to the baby's hands and head while adjusting the backrest.

Seat unit canopy
The seat is equipped with a removable canopy. To assemble, please slide onto the
ttings situated on each side of the seat (22).
To remove the canopy, press the red buttons located on each side of the seat and
slide the canopy out of the ttings (23).
Seat unit canopy
To increase the size of the canopy, open the zip on the back (24).
To increase ventilation open the ap (25).
To adjust the position of the canopy, pull forwards to provide more cover and
backwards to open (26).
Seat cover
The seat is equipped with an apron, this can be attached to the canopy in 2
positions via press studs (27).

Footrest
To change the angle of the footrest, press both buttons located on each side,
while simultaneously adjusting the footrest to the desired position (28).
To extend the footrest, pull it up and towards you and to shorten push it down (29).
Bumper
The seat is equipped with a safety bumper bar (30). To install it, insert the end of
the bar into the connection points on either side of the seat until you hear a
‘click’. To remove it, press the button on the outer side of the connection point
and pull the bar upwards (31).
ATTENTION! Always use a bumper bar in combination with the safety harness.
Safety harness
The stroller is equipped with a 5-point safety harness, always use the safety
harness when a child is in the seat, fasten the seat belts by pushing the buckles
into the central buckle housing (32a), and then tighten the straps.
To unfasten the seat belts press the central button while pulling the buckles out
of the main buckle housing (32b).
To install the straps, take the rectangular tabs sewn at the end of each strap and
push through the slots in the fabric cover and plastic seat unit. Then pull the
belts on the seat side to check that they have fastened correctly (33).
ATTENTION! Always use the safety harness when there is a child in the seat.

Rain cover and insect net
The stroller is equipped with a raincover, that can be used both for the carrycot
and seat unit (35).
It is also has 2 insect nets: 1 for the carrycot, which is attached with zippers to
the inside of the canopy and velcro to the edge the carrycot and 1 for the seat
unit that is pulled over the seat and tucked under footrest (34).
Basket
To install the basket, zip it onto the lower part of the frame.
ATTENTION! The maximum load of the basket is 2 kg.
Bag
The stroller is equipped with a bag for accessories, you can fasten it on the
stroller handle using the location points on the handle (40).

Folding a frame with the seat unit
To fold the frame with the seat unit, the seat must be in the forward facing
position (36). First fold the footrest completely under the seat (37), then fold the
handle down 90 degrees (38). Next, press the backrest adjustment so it is folded
at against the seat (38). Finally, press buttons on both sides of the frame and
fold the handle down until it is folded and locked in the position shown (39).
Car seat
To t the car seat onto the stroller frame, rst plug the adapters into the slots on
both sides of the frame until your hear a ‘click’ (41-A). Next, line the car seat up
with the adapters and insert into the adapter sockets, until your hear a ‘click’(42).
To remove the seat, press the buttons on both sides and pull the seat upwards
(43). To remove the adapters, press the lock button located on the inside of
adapters and pull upwards(41-B).
ATTENTION! To mount the car seat onto the frame, rst mount the adapters into
the frame slots.
ATTENTION! Before installing the seat, make sure that the adapter is correctly
installed on the stroller frame.
ATTENTION! The seat is designed for children up to 13 kg body weight.
ATTENTION! Before using the stroller make sure the seat is correctly installed.

Foot cover and car seat canopy
To use the canopy, rst move the car seat handle into the upright position, then
pull the canopy upwards over the handle, snap the press studs together around
the handle to keep it in position (44).
The foot cover can be xed in position using the press studs located on the inside
of the canopy (45).
Adjusting the car seat handle
To adjust the car seat handle, press the buttons on both sides of the seat and
then move the handle to the desired position (46).
Instructions for assembling the seat into the car is attached on the car seat.
Carrycot ventilation
Rotate the vents clockwise / anticlockwise to vary the carrycot ventilation
(48,49).
Handmus
Use the press studs to attach the handmus to the stroller handle (50).

Maintenance instructions:
• To ensure your baby is protected from accidental injury, please
check and maintain the travel system regularly.
• Please use a cloth or brush to clean the seat fabric and use
neutral 10℃-40℃detergent to clean other parts.
• Please do not store in direct sunlight and rain.
• Regularly check if there are loose screws, damaged parts or
broken stitches, if necessary replace the damaged parts.
•
• Oil the rotating mechanism to ensure smooth rotation.
Please use the travel system carefully following the instructions
to avoid damage or accidental injury.
Attention:
• Please check all components are installed correctly and fastened in place
before each use.
• Do not let the child climb into / out of travel system or stand on the
seat or carrycot.
• Do not use the stroller on rough ground, near re and other
dangerous areas.
• Avoid using or storing the travel system in wet, cold or high temperature
environments, keeping it away from re or strong heat.
Contact Mee-go:
Mee-go Ltd
Unit 5, Victoria Mills
Mill Street, Dewsbury
West Yorkshire
United Kingdom WF12 9AQ www.mee-go.co.uk