MEI CashFlow 130 User manual

Teaching a New Token
The following procedure must be followed in order to
teach a new token into channel 1.
NOTE:- Rotary data switch position “E” is used to
program tight window token limits and ‘F’ standard
window token limits.
1.Switch OFF the power to the validator.
2.Set the 4 way DIL teach switches 2, 3 & 4 to
ON, ON & OFF (channel 1) or OFF, ON & ON
for (channel 0)
3.Set rotary data switch to position “F”
standard window limit.
4.Switch ON the power to the product.
(The LED will start flashing).
5.Insert 10 to 20 (minimum 10) of the desired
tokens through the validator.
6.Return the 4 way DIL switches 2, 3 & 4 to
Normal Operation settings.
(LED will stop flashing and stay ON to indicate
success).
If the LED continues to flash OFF a number
of times this indicates a failure to teach the
new token. See LED Assistance Codes table
for help and then restart procedure again.
7.Token is now programmed and ready to use.
(New token information has been stored in
coin channel “1” which is rotary switch position
“1”). Any previous taught token information
in this channel will be overwritten).
NOTE:- If token self teach is successful but token
taught is rejected i.e. gives 3 flashes of the LED,
check that channel “1” is enabled.
To enable the new token set the rotary data switch
to position “1” then refer to enabling coin or tokens
configuration procedure).
MEI,
Internet: http://www.meigroup.com
CashFlow®130
Quick Reference Guide
Applies to Product Version G1
MADE IN THE E.C. (UK)
PATENTED
¨
Internet:http://www.meiglobal.com
R
RGB001HA0103
Typical coin set label
Rotary
Data Switch
Configuration
Switches
Green Diagnostic
LED
--15F
--14E
--13D
Y
es
£2
12
C
Yes
£2 Tight
11
B
Yes
A
£2 Tight10AYes£199 Yes
F
£188 Yes50p new77 Yes50p new66 No
E
50p old55
Yes
D
20p
4
4
Yes
C
10p
3
3
No
-
5p22
Yes
B
Token 2
1
1
No
B
Token 1
0
0
Coin
Enabled
Coin
Output
Coin
Type
Channel
Affected
Position
27364 G2719550044

Using 4 Way DIL
&
Rotary Data Switches
To achieve a successful change to the configuration of
the validator the following procedure must be followed.
1.Switch OFF the power to the validator.
2.Set the 4 way DIL switches to the
configuration settings required. (See Product
Configuration Table)
3.Select the required data / channel position
using the rotary data switch. (see product
configuration table)
4.Switch the validator power ON. (The LED will
start flashing).
5.Return the 4 way DIL teach switches back to
Normal Operation Settings. (Switches 2,3 & 4
set to all ON or all OFF).
6.The LED will stop flashing and will stay ON.
This will indicate a successful change and that
the validator is ready for normal operation.
NOTE:- If teach is entered by mistake, switch OFF
the power to the validator before moving the 4 way
DIL switch positions else the mech. may learn
something unintentionally.
No power to validatorOFF Validator is set in teach modeFlashing Coin inhibited by validator or machine4 x Flash Coin inhibited by validator3 x Flash Coin rejected as unrecognised2 x Flash Reject lever pressed or coin accepted1 x Flash Power is ON validator is O.K.ON MEANINGSTATE
What Is The Green LED Doing?
Product Configuration
Normal Operation Settings
234
ON
1
234
ON
1
Set switches 2, 3 & 4 to
OFF or ON
-FAuto configuration -DParallel output ONOFFOFF
-CBinary coded output
Selecting Machine Interface Types
-
-
-
OFF
-
Set the alarm
OFF
-
-
-
ON
-
Set the alarm
ON
ON
OFF
ON
-
E
Fraud Defe
nce teach channel 0
OFFONON-
s
E or F
Self teach a token for channel 1 ONONOFF-
s
E or F
Self teach a token for channel 0 OFFOFFON-0 - FEnable a coin or token channel OFFONOFF-0 - FInhibit a coin or token channel
SW4SW3SW2SW1
234
ON
1
2 3 4
ON
1
Channel
Position
Product Configuration Table
What Do You Want To Do?
w E = Tight Window Limits. Channel F = Standard Window
Limits
x 8 Token material outside
acceptable limits
x 7
Token diameter outside
acceptable limits
x 6 Check that there are no mixed
sample tokens
Token thickness outside
acceptable limits
x 5
Ensure that the rotary switch is
set to “F”
Incorrectly set rotary
switch position
x 4
Ensure at least 10 tokens have
been inserted
Not enough sample tokens
inserted
x 3
No activity was registered
within 30 seconds
Validator timed outx 2
Reason/Action
Description
for Code
LED
Flashes
Teaching Token (LED Assistance Codes)