Melten M2 Nurse Call Module User manual

Melten
M2 Nurse Call Module
User Guide
Model NO.: BM-B01

Revision History
Version
Date
Revision
0.1
2018.7.1
First Draft
0.2
2018.8.16
Add the FCC warning messages in the “Important Notice” section.
0.3
2018.8.20
Modify the product name and add the product specification table.
0.4
2018.8.21
Add the product model number

Important Notice
All Rights Reserved
No part of this publication may be reproduced, transcribed, or transmitted in any form, or by
any means electronic or mechanical, including photocopying and recording, for any purpose
other than the purchaser’s use without written permission of Melten Inc. (Melten).
Trademarks
Melten is a registered trademark.
Warranty and Limited Liabilities Disclaimer
Information in this document is subject to change and does not represent a commitment by
Melten. Changes made to the information in this document will be incorporated in new
editions of the publication. No responsibility is assumed by Melten for the use or reliability of
software or equipment that is not supplied by Melten or its affiliated dealers.
Melten warrants this product free from defects in material or workmanship for a period of 12
months from the ship date, except as noted. The product warranty does not cover damage
caused by misuse, abuse, act of gods, the attachment of any accessory/components not
provided by Melten, alteration to the product, improper installation, lack of proper
maintenance, or any other conditions that are beyond the control of Melten. Melten shall not
be responsible for any type of incidental, consequential, or special damages. All implied
warranties, including but not limited to those warranties of fitness and merchantability, are
limited in the total duration to 12 months from the original ship date. Claims for lost
shipment, damaged shipments, or other problems regarding freight must be made directly
to the responsible carrier. Melten disclaims any and all liability for consequential or incidental
damages. No responsibility is assumed by Melten for the use or reliability of software or
equipment that is not supplied by Melten.
Precaution

All peripheral or connected devices such as network switch, server, or software must be
tested and verified by Melten before installations.
BM-A01 supports BT4.0 and WiFi (802.11 b/g/n) interfaces. The configuration can only be
configured by certified Melten engineers and please also contact Melten before using it.
Changing the radio frequency and power is prohibited and may consequently violates the
radiation law in any country.
*Maximum wireless signal rate derived from IEEE Standard 802.11ac and 802.11n specifications. Actual data
throughput will vary. Network conditions and environmental factors, including volume of network traffic,
building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range.
⚫802.11n/g/b/a Compatible
⚫BT4.0 Supported
⚫Operating Temperature: 0°C (32°F)~+40°C (104°F)
⚫Storage Temperature: 0°C (32°F)~+50°C (122°F)
⚫Humidity Control: 20% to 80% (non-condensing)
A Statement and Advisory from Melten Inc.
This manual is designed to instruct all personnel responsible for proper installation, use and
care of the Melten Smart Ward IoT System and M2 nurse call module. All users are urged to
carefully read these instructions before operating the system.
The instructions described in this manual are the only officially approved operating methods
by Melten Inc. (Melten) and should be followed except for any statutory obligation. All users
and technicians should become familiar with the warnings, cautions, and instructions
contained herein. Do not operate or service the system until you have become familiar with
this information.
The system must be installed and serviced by competent personnel. Do leave this manual
with the users and technicians after installation. If you are in any doubt, contact your Melten
representative for details.
Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
Caution:
Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.
RF Exposure Warning
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.