Memorex ILIVE User manual

Important Safety Instructions
• Read these Instructions.
• Keep these Instructions.
• Heed all Warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including ampliers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding - type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not t into
your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories specied by the manufacturer.
• Unplug this apparatus during lightning storms or when unused for long
periods of time.
• Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
• Use only with a cart, stand, tripod, bracket, or table specied by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
FCC Warnings
Warning: Changes or modications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
Overview
a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings and Precautions
• WARNING: Shock hazard - Do Not Open.
• CAUTION: Use of controls or adjustments or performance of procedures
other than those specied may result in hazardous radiation exposure.
• WARNING: Changes or modications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment.
• WARNING: Do not place this unit directly onto furniture surfaces with any
type of soft, porous, or sensitive nish. As with any rubber compound made
with oils, the feet could cause marks or staining where the feet reside. We
recommend using a protective barrier such as a cloth or a piece of glass
between the unit and the surface to reduce the risk of damage and/or staining.
• WARNING: Do not ingest battery, chemical burn hazard.
• Battery shall not be exposed to excessive heat such as sunshine, re or the
like.
• Lithium batteries, like all rechargeable batteries, are recyclable and should
be recycled or disposed of according to state and local guidelines. They
should never be disposed of in normal household waste and they should never
be incinerated, as they might explode. Contact your local government for
disposal or recycling practices in your area.
Features
• Bluetooth wireless
• Voice prompts announce speaker functions
• 8” full range speaker
• LED light effects
• FM scan radio
• Microphone input
• Rotary volume control
• 3.5mm Aux in
• USB port - supports MP3 le format
• Carry handle
• Built-in rechargeable battery
• Battery life: approx. 4 hours at 50%
WARNING: To reduce the risk of electric
shock, do not remove cover (or back). No
user-serviceable parts inside. Refer servicing
to qualied service personnel.
WARNING: This product can expose you to
chemicals including lead, which is known to
the State of California to cause cancer. For
more information go to: www.P65Warnings.
ca.gov This product meets and complies with
required Federal product guideline/
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user accessible
parts.
The lightning ash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of un-insulated
“dangerous voltage” within the product’s
enclosure that may be of sucient magnitude
to constitute a risk of electric shock to persons.
Control Panel
1. Power/Volume Wheel: Turn to power ON/OFF and adjust volume level
2. Charging Status LED: Solid red light when charging. When the unit is
fully charged, the light will turn off.
3. DC Power Input: Use to charge the internal battery and power the
speaker. Charge time is approximately 4 hours.
4. Aux in (3.5mm Input)
5. Source/LEDs: Press to change audio source between Bluetooth, Aux in,
USB, and FM. Press and hold to turn LED lights ON/OFF.
6. Next/Previous/TWS: Press to skip to next track or replay previous track.
In FM Mode press to cycle through radio stations. In Bluetooth mode,
press and hold the / TWS button to enter Party Plus mode which
will allow this speaker to pair with another ISB200 speaker for True
Wireless Stereo.
7. Play/Pause/Pair: Press to play/pause a track. In FM Mode press to start
auto-search and save all scanned radio stations. In Bluetooth mode,
press and hold for 3 seconds to manually pair to a Bluetooth device.
8. USB Port
9. Microphone Input
7
9
8
6
5
4
3
2
1
Wireless Tailgate Party Speaker
MSB200 v2784-01

To download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support
section at: www.Memorex.com
Para descargar este Manual del Usuario en inglés, español y francés, o para obtener respuestas a preguntas frecuentes, visite la
sección de apoyo en: www.Memorex.com
Pour télécharger ce guide de l’utilisateur en anglais, espagnol ou français, ou pour obtenir des réponses à des questions
fréquemment posées, consultez la rubrique d’assistance sur: www.Memorex.com
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.Memorex.com
Customer Service: 1-888-999-4215 | Email Support: [email protected] | Email Parts: [email protected]
Copyright © 2020 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their
respective owners. Specications are subject to change without notice.
Customer Support
Protect for Today
Sustain for Tomorrow
Made
Green
Aux In
Requires a 3.5mm audio cable (not included).
1. Connect a 3.5mm audio cable to the Aux In on the unit and the
audio output/headphone jack on an audio device.
2. Press Source/LEDs to switch to Aux in mode.
3. Use the controls on the connected device to select and play audio.
Bluetooth Wireless
Pairing & Playing Audio
1. Press the Source/LEDs button to select Bluetooth Mode.
2. When the speaker is ready to pair a voice prompt will sound. Using the
controls on your Bluetooth device, scan for and select ISB200 in your
Bluetooth settings to pair. Refer to the user’s manual for your specic
device for instructions on pairing and connecting Bluetooth devices.
3. When successfully paired, a voice prompt will sound from the unit.
4. Use the controls on the connected device to select and begin playing
audio. Audio played through the connected Bluetooth device will now
be heard through the speaker. Use the controls on the speaker or the
connected device to play, pause, and adjust volume.
Note: After initial pairing, the unit will stay paired unless unpaired manually by
the user or erased due to a reset of the device. If your device should become
unpaired or you nd it is unable to connect, press and hold the Play/Pause/
Pair button to pair manually and repeat the above steps.
USB Drive
1. Load a USB drive into the USB media drive
2. The speaker will automatically switch to USB mode.
3. Use the controls on the speaker to select and play and pause audio
from the connected USB drive.
FM Radio
1. To use the FM radio, press the Source/LEDs button to switch to FM
mode.
Auto Search and Saving Stations
2. To use the auto search function press the Play/Pause/Party Plus
button while in FM mode.
3. The radio will auto search stations and save them.
4. To cycle through the saved stations press the Next/Previous buttons.
Using the Microphone
To use a microphone, plug a microphone into the Microphone Input and the
speaker will project your voice out loud. Use the Volume Wheel in order to
control the volume of the microphone.
Charging the Battery
1. To power the unit or charge the internal battery, connect the DC Power
Input on the speaker to a standard power outlet using an AC/DC power
adapter.
Party Plus Mode.
Party Plus Mode allows two identical “MSB200” speakers to pair together for
a stereo sound effect.
1. To enter Party Plus Mode, Power ON both speakers and set to
Bluetooth mode.
2. Press and hold the button on one of the units until an audible
chime is heard. The speakers will attempt to pair to each other.
3. When the 2 speakers are paired together a voice will announce the
connection.
4. Connect Bluetooth device to speakers using the steps from the “Pairing
and Playing Audio” section above.
5. Use your device to select and play tracks. The audio will now be heard
through both speakers.