Memphis Shades 2320-0018 User manual

MOUNTING INSTRUCTIONS
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
1. Cover gas tank and front fender with towels to avoid
damage during installation.
2. Install the windshield mounting plates onto the windshield,
using the bolts that are pre-assembled on the mounting plates.
The Santoprene grommets should be inserted through the
holes in the windshield so that the flat round part of the grommet
lies flat on each side of the plastic. Tabs point in towards the
headlight. (see figure 1).
3. Install the windshield by placing the lower slots into the
lower mounting bushings. Slip the upper slots into the upper
mounting bushings and gently but firmly seat the slots into
place.
Lock the locking mechanism into place. (see figure 2 and 3)
Note: This is a detachable windshield, ALWAYS make sure
the Locking Mechanism is Fully Engaged after installing
the windshield! (see figure 3)
Read and follow these directions carefully.
During installation, make certain that when turning the
forks, there can be no interference with wiring or cables
AND, that the mounting hardware can not hit the
gas tank, through the windshield's full range of ad-
justment.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
MEM8820 01-01-08
Figure 2
Figure 1
2320-0018 SPORTSHIELD PLATE ONLY KIT
DETACHABLE MOUNTING KIT H-D WIDE

2320-0018 SPORTSHIELD PLATE ONLY KIT
DETACHABLE MOUNTING KIT H-D NARROW
MOUNTING INSTRUCTIONS
MEM8820 01-01-08
CORRECT
Fully engaged
Locking mechanism
NOT CORRECT
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
123
Figure 3
4
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
R322C/T
LATCH
ASSEMBLY
1. M1135
2. M1136
2 1
2320-0018 SPORTSHIELD PLATE ONLY KIT
PART #
M1135
M8820
M1136
DESCRIPTION
LEFT SPORTSHIELD MOUNTING PLATE
MOUNTING INSTRUCTIONS
RIGHT SPORTSHIELD MOUNTING PLATE
QTY.
1
1
1
M302 1/4"-20 x 1/2" SS SOCKET HEAD CAP SCREW 4
M504
SOCKET SHOULDER WASHER 4
M543
SANTOPRENE GROMMET 4
M505
BUTTON NUT 4
R322C CLUTCH SIDE LATCH ASSEMBLY 1
R322T THROTTLE SIDE LATCH ASSEMBLY 1
R334 6-32 X 3/8" FLAT HEAD SS SCREW 8
R326 SS SPRING 2
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
you can also reach us at
[email protected]