Memphis Shades 2320-0074 User manual

2320-0074 SPORTSHIELD MOUNTING KIT HD V-ROD, BLACK
MOUNTING INSTRUCTIONS
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
No additional tools required for this kit.
1. Cover gas tank and front fender with a towel to avoid
damage during installation.
2. Install the windshield mounting plates onto the windshield,
using the bolts that are pre-assembled on the mounting plates.
The Santoprene grommets should be inserted through the
holes in the windshield so that the flat round part of the grommet
lies flat on each side of the plastic. The tabs point in towards
the headlight when installed correctly. (see fig. 1)
3. Loosely install the four Fork Clamps on the forks, approxi-
mately 1" down from the upper triple tree and 1-3/4" apart.
(see figure 2)
4. Install headlight visor. With black side up, form visor
around headlight, smooth curve facing forward. Push it in
between the headlight bracket and headlight nacelle until the
ends firmly locate on the headlight bolts at both sides. (see
Fig.2)
5. Start with Fork Clamp Bushing adjusted to rear of slot (see
figure 2 and 3) Then adjust as needed and check for clear-
ance. (See warning above.)
6. Slip the windshield mounting plates and windshield onto
the fork clamps, (see figure 3 and 5) and secure the left and
right side locking mechanism
(CONTINUED)
7. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after
installing the windshield! (see figure 5)
Read and follow these directions carefully.
During installation, make sure that the windshield and hard-
ware do not interfere with any cables or wiring when the forks
are turned all the way in either direction. Also make sure,
through the full range of adjustment, that the windshield and
hardware do not hit the tank.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
Fig.1
Fig. 2
WARNING:
"Mounting clamps
backwards will cause
damage to your tank."
Throttle side,
front of bike
INCORRECT
Throttle side,
front of bike
CORRECT
Fig. 3
Form visor and
push it in until
it firmly locates
on the headlight
bolts.
MEB8927 12-20-10

1. M520
2. M533
3. M1171EB
4. M1170EB
5. R310
2320-0074 SPORTSHIELD MOUNTING KIT HD V-ROD, BLACK
MOUNTING INSTRUCTIONS
CORRECT
Fully engaged
NOT CORRECT
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
Figure 5
1234
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
R322C/T
LATCH
ASSEMBLY
2
3
1
BUSHING
ASSEMBLY
4
2320-0074 SPORTSHIELD KIT
5
BUSHING ASSEMBLY
A C
C
D
E
F
A. R329
B. M369
C. R323-B
D. R324
E. R318EB
F. M306-B
B
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
You can also reach us at
[email protected]
Part# Description Qty
B8927 Mounting instructions 1
M1171EB Clutch mounting plate, black 1
M1170EB Throttle mounting plate, black 1
M520 Inner adjustable fork clamp 4
M533 Medium, outer adjustable fork clamp 4
M504EB Socket shoulder washer, black 4
M505EB Button nut, black 4
M543 Santoprene grommet 4
M302-B 1/4”-20x1/2” SS socket head screw, black 4
M369 Stainless steel washer 4
M306-B 1/4”-20x5/8” SS socket head screw, black 4
Part# Description Qty
R329 Slot nut 4
R322C-B Latch assembly, Clutch, Black 1
R322T-B Latch assembly, Throttle, Black 1
R318EB 1” Socket shoulder washer, black 4
R324 #207 EPDM O ring 4
M303 1/4”-20x3/4”SS socket head screw 4
R310 Headlight visor 1
M313 3/16” allen wrench cover 1
M310 3/16” allen wrench 1