Part No. 2320-0176
Trigger-Lock Mounting Kit - Polished
Memphis Fats / Slim Windshield
HD FXDL 2014 and up
1.
2.
3.
This is a detachable fairing / windshield, ALWAYS make
sure the locking mechanism is fully engaged.
1.
2.
3.
Before assembly, read Warnings inside
1. Kit Contents
REVISION 0
Aluminum parts are electrocoated (E-coated)
for durability and weather resistance.
WARNING
During installation, make sure that the fairing / wind-
shield and hardware do not interfere with any cables
or wiring when the forks are turned all the way in either
direction. Also make sure , through the full range of
adjustment, that the fairing / windshield and hardware
do not hit the gas tank.
The improper installation of this kit and related
components could result in serious injury or death.
CAUTION
Memphis Shades fairings / windshields are made from
Luciteacrylic, and will last for years with proper care.
Clean your fairing with plenty of soapy water (mild dish-
washing liquid is best) and a soft cotton cloth. Use your
bare hands to feel and dislodge bugs, or cover with a
wet, soapy towel and let it soak. Don’t use paper towels
and scrape with anything. Small scratches can be re-
moved with NOVUS #2.
Never use any glass cleaning products, petroleum
based chemicals, or cleaning agents with ammonia,
bleach or any other harsh chemicals. This includes (but
not limited to) RainX, brake fluid, acetone, paint thinner,
benzene and gasoline. “If it hurts your nose, it will hurt
the plastic.”
Glass cleansing agents will cause severe damage to
your fairing, and will void your warranty.
For care and cleaning we recommend using Memphis
Shades All Kleer, a unique cleaner/polish, bug
remover and rain repellent that leaves a super slick
surface that makes the next cleaning even easier.
4. At certain times of the day the Sunlight can reflect off
the curvature of a fairing / windshield and cause ex-
treme heat build-up on motorcycle instruments and in-
strument panel. Take care when parking. Park facing
the sun, place an opaque object over the instruments or
adjust the fairing / windshield to avoid reflections.
MEK2013
Ref Code Part Name Qty
I2013 Mounting Instructions 1
M1607EC Clutch side mounting plate 1
M1608EC Throttle side mounting plate 1
S1167 Medium detachable clamp assembly 4
M310 Short arm allen wrench, 3/16 1
M314 T-Handle Wrench, 3/16 1
Additional tools required that are not included in this kit. 1/2”
wrench, 7/16” wrench.
1. Cover gas tank and front fender with towels to avoid
damage during installation.
2.Install the two Mounting plates andonto the fairing
using the nuts and washers supplied. The small tab goes to
the bottom of the fairing, the big one goes to the top. The
tabs point out away from the headlight (Fig. 2)
3. Loosely install the four Fork Clamps on the forks, approxi-
mately 2" apart. (Fig 2)
4. Start with Fork Clamp Bushing adjusted to rear of slot
(Fig 4) Then adjust as needed and check for clearance. (See
warning above.)
5. Slip the windshield mounting plates and windshield onto
the fork clamps, (Figs 3 and 5) and secure the left and right
side locking mechanism.
2. Mounting Instructions
Memphis Shades warrants all product components, metal
and plastic, against defects in materials and workmanship for
24 months.
For Parts and Warranty Help, Contact:
Memphis Shades, Inc.
P.O. Box 429
Rossville, TN 38066
(901) 853 0293
Visit us on the web at www.memphisshades.com or you can
also reach us by email:
customerservice@memphisshades.com
#memphisshades
