MERLYN Nexa 231250 User manual

2 DOOR QUADRANT
PATENT PENDING

PH2
MG3MMALKEY x 1
K024 x 2 K048 x 4 K049 x 4
K010 x 2
Cover cap of
wall profile

1
1
2
3
4
5
6
9
10
11
12
13
7
8
14 15 16 17 18
19
20
21
22
No.Qty Code
12
2 6
3
4
5
6
7
8
9
10
No.Qty Code
11
12
13
14
15
16
17
18
19
20
No.Qty Code
21
22
6
2
2
2
2
2
4
2
8
4
4
2
4
8
2
4
2
2
4
4
K010
2SP12
2SY51
A
K001/002
B
K024
K126
K156
K073
K165
K120
K124
K114
K143/K144
K145
K008/009
K005/006
K158
K054~K060
K049
K048

Please ensure your tray is 100% level in all directions before fitting your
enclosure.
2
100%level!

3
2
3
size X
800x800 770-790
900x900 870-890
1000x800 970-990
1200x800 1170-1190
1200x900 1170-1190
770-790
870-890
770-790
770-790
870-890
Y
X
Y
900x760 870-890 730-750
900x800 870-890 770-790
size
X
Y
XY
Inside
A
B
Min.10mm
Inside
A
B
Min.10mm
A. Mark the position of the outside of each wall profile within the adjustments in step 2.
B. Before marking the fixing positions check the label on the back of the profile indicating the
side of the profile to face inside !
Sizes with equal adjustment both sides
Offset sizes
Y
800x800 and 900x900 size have the same adjustment on each side.
All other sizes are offset and can be fitted with the wider panel on either side depending on
the handing of your tray. For offset sizes check which side the wider fixed panel is on and if
needed swap X&Y.

4
4
5
A
B
A
B
C
D
2SY51
Build the product on the tray starting with the bottom profile.
A&B. Slide the wall profile fully over the nylon bracket.
C&D. Load the 4 x 30 screw onto the tool provided and fix the wall profiles top, middle and bottom.

5
6
7
A
B
C
D
A
B
C
Min.50mm
A. Slide the clip K143/K144 away from the seal on the top and bottom of the frame.
B. Remove the PVC installation tool by releasing the side closest to the top first, then lift out
from the frame.
C. Leave the bottom PVC installation tool in place to aid the fitting of the fixed glass panel.
Note: make sure the installation tools are positioned at each end of the bottom seal.
K143/K144
Slide the top frame fully into the ends of the wall profiles. Check the frame is locked in place
and does not slide back out of the frame.

8
9
A
B
A. Standing inside the enclosure, place the bottom of the fixed panel on the frame at a slight
angle. Then lean the panel forward into the top frame.
B. Slide the glass panel into the wall profile.
Adjust the top and bottom profile to align the glass with the red line on the labels while
ensuring the glass is plumb.
6

7
10
11
AB
C
K165
Inside
H
2
O
H
2
O
A. Slide the clip over the fixed panel on both the top and bottom.
B. Starting at the bottom use the tool provided to insert the wedge gasket between the glass and the
profile. Keep the flat side to the glass and the ridged side to the profile.
Top Tip ! Dampen the seal with water to help slide into place.
C. Remove the bottom PVC installation tool by releasing the side closest to the bottom first, then lift out
from the frame.
Tighten the grub screws until they are flush with the 'adjusting block'.
Adjusting block
K143/K144

12
13
K048
K049
Slide the rollers labeled 'TOP' onto the top and the 'BOTTOM' onto the bottom housings.
8

9
14
15
A
BD
C
A
B
K010
K120
K124 K126
K024
Adjust the rollers to ensure there are no gaps between the magnet seals.

10
DOP:CEKA1.1
Https://merlynshowering.com/aftersales-support/dop-certs/
and at the base of the clip where it sits on the frame.
16