Micon Ezee Glow Wee Hugo User manual

1
Ezee Glow Wee Hugo
Model Number - MZEWHES
OWNER’S MANUAL
Installation & User Instructions
This product is only suitable for well insulated spaces and occasional use.
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND
RETAINED FOR FUTURE REFERENCE.

2
SAFETY INSTRUCTIONS
Please read all instructions carefully before using this appliance.
This heater must be used on an AC supply only and the voltage marked on the heater must
correspond to the supply voltage.
Do not switch the appliance on until it’s properly installed as described in this manual.
Never leave the appliance unsupervised when in use.
If you have to leave even for a short moment please stop the appliance.
Only use the appliance for domestic purposes and in the way indicated in these instructions.
From time to time check the cord for damages. Never use the appliance if the cord or any part of
the appliance shows any signs of damage.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
Make sure the connection cord does not touch any hot surfaces.
WARNING: In order to avoid overheating, do not cover the heater.
Do not use the appliance outdoors.
Do not use if you have wet hands.
Never use the appliance on or near hot surfaces.
Never move the appliance by pulling the cord.
Before cleaning the appliance, make sure it’s unplugged from the power and that it’s completely
cooled.
Do not clean the appliance with abrasive cleaners or chemicals.
Never use accessories that are not recommended or supplied by the manufacturer. It could cause
danger to the user or damage to the appliance
The heater must not be located immediately below a socket outlet.
Do not use this heater with a programmer, timer or any other device that switches the heater on
automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
This appliance is not intended for use by persons (including children) who require supervision
or have a lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided
that it has been placed or installed in its intended normal operating position and they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved.
Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance
or perform user maintenance.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved.
Cleaning and user maintenance shall not be made by children without supervision.
CAUTION —some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.

3
PLACEMENT
This heater is designed to be placed on a hard, level surface. When positioning, please keep the
following points in mind:
•If you are placing the heater in an alcove, make sure that there is at least 150mm of space on all sides
to ensure good air circulation.
•The heater must not be located over a fixed electrical socket. The socket must always be accessible in
order to disconnect the heater from the electrical supply for maintenance or when replacing a lamp.
•Keep hearth rugs and other soft furnishings away from the front of the heater. They could obstruct the
free flow of hot air from the fan and damage both soft furnishings and heater.
CONTROLS
Never cover the heater or obstruct the opening at the base of the heater, this could cause
overheating and consequently risk of fire.
LOCATION OF CONTROLS
The following switches are located under the front door of heater.
1. Thermostat knob - Adjust to maintain room temperature
2. Flame dimmer knob - Adjust to set flame intensity
3. Flame switch - Turn on/off for flame/fuel effect
4. Heater switch 1 - Turn on/off for one of 900W heat settings
5. Heater switch 2 - Turn on/off for one of 900W heat settings
150mm
150mm
Control
s
1 3 4 5 2

4
OPERATION INSTRUCTIONS
•Insert plug into mains socket
•Open the front door.
•Select the desired functions:
- Flame/fuel effect on/off (3)
-Low heat setting 900W (3 + 4)
-High heat setting 1800W (3 + 4+ 5)
-Heating and Flame effect (1 + 2 + 3 + 4 + 5)
•Increase or decrease flame intensity by clockwise or anti-clockwise rotation of the flame dimmer
knob (2).
•Rotate thermostat knob (1) clockwise or anti-clockwise to increase or decrease desired room
temperature setting.
Notice: Heater will only work if flame switch (3) is on and thermostat is set above current room
temperature.
SAFETY CUT-OFF
This appliance is fitted with a safety cut-off which will operate if the fire overheats (e.g. Due to blocked
air vents). For safety reasons, the fire will NOT automatically reset. To reset the appliance, disconnect the
appliance from the mains supply for at least 15 minutes. Reconnect the supply to the mains and switch on
the appliance.
BULB REPLACEMENT
·The bulbs inside the heater are LEDs and aren’t replaceable.
CLEANING AND CARE
⚫Before cleaning, always remove the plug from the electrical socket. Ensure that the unit is cool
enough to work on.
⚫Do not use harsh chemicals or solvents to clean this product and avoid using abrasive cleaning
agents.
⚫The heater and glass parts only need wiped clean with a dry, soft cloth; do not use polishes or
abrasive materials.
⚫Do not immerse in water or liquid when cleaning.
⚫Use a slightly damp, lint-free cloth to clean the appliance.
TROUBLE SHOOTING
No heat or light: Check the wall socket by plugging in a working appliance. If socket is functional, and
the cord or plug of the heater is suspected to be faulty, have it checked by an electrician.
Light but no heat: Check that the Thermostat on the stove is set above the current room temperature.
Alternatively, the thermal cut-off may have engaged - see thermal cut-off section.
TECHNICAL SPECIFICATION
Voltage: 220-240V~ 50Hz
Power Consumption: 1800W
Bulb: LED’s
Dimensions: 390mm x 550mm x 258mm

5
Model
MZEWHES
Item
Symbol
Value
Unit
Item
Unit
Heat output
Type of heat input, for electric storage local
space heaters only (select one)
Nominal
heat output
Pnom
1.8
KW
manual heat charge control, with
integrated thermostat
Not applicable
Minimum
heat output
(indicative)
Pmin
0.9
KW
manual heat charge control with
room and/or outdoor temperature
feedback
Not applicable
Maximum
continuous
heat output
Pmax,c
1.8
KW
electronic heat charge control
with room and/or outdoor
temperature feedback
Not applicable
Auxiliary electricity consumption
fan assisted heat output
Not applicable
At nominal
heat output
elmax
0.012(fan
motor)
KW
Type of heat output/room temperature control
(select one)
At minimum
heat output
elmin
0.012(fan
motor)
KW
single stage heat output and no
room temperature control
[no]
In standby
mode
elSB
0
KW
Two or more manual stages, no
room temperature control
[no]
with mechanic thermostat room
temperature control
[yes]
with electronic room temperature
control
[no]
electronic room temperature
control plus day timer
[no]
electronic room temperature
control plus week timer
[no]
Other control options (multiple selections
possible)
room temperature control, with
presence detection
[no]
room temperature control, with
open window detection
[no]
with distance control option
[no]
with adaptive start control
[no]
with working time limitation
[no]
with black bulb sensor
[no]
Contact details
Micon Distribution Ltd.
1a Hallstown Road, Ballinderry Upper, Lisburn BT28 2NE

6
Manufacturers name:
Micon Distribution Ltd.
Manufacturers address:
1a Hallstown Road, Ballinderry Upper,
Lisburn, BT28 2NE
ELECTRICAL CONNECTIONS –UK PLUG WIRING INSTRUCTION
·If the plug has to be changed because it is not suitable for your socket, or due to damage, please follow
the wiring instructions shown below.
·The wires in the mains lead are coloured in accordance with the following code:
BROWN : LIVE (L)
BLUE : NEUTRAL (N)
GREEN/YELLOW : EARTH (E)
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, please see below:
·The BLUE wire is the NEUTRAL and must be connected to the terminal which is marked with the
letter N or coloured BLACK.
·The BROWN wire is the LIVE and must be connected to the terminal that is marked with the letter L
or coloured RED.
·The wire which is coloured GREEN/YELLOW must be connected to the terminal which is marked E
or the earth symbol or coloured GREEN or GREEN/YELLOW.
·Always ensure that the cord grip is positioned and securely fastened.
·WARNING: THIS APPLIANCE MUST BE EARTHED.
·If a 13A (BS1363) fused plug is used it must be fitted with a BS1362 13A fuse. If in doubt consult a
qualified electrician.

7
PRODUCT WARRANTY
Your product is guaranteed for one year from the date of purchase.
Should this product prove defective within one year of purchase due to a design fault, workmanship or
material breakdown, the product will be repaired or replaced free ofcharge.
Product warranty is subject to the following conditions:
•The product is to be used for domestic purposes only in accordance with the operating
instructions.
•Responsibility of proof of purchase lies with the end user(s), who must prove product purchase
within 12-month period of claim date.
•All warranties will be invalidated if unauthorised repairs or modifications are made to the
electric fire, or in case of accident, misuse or damage caused by improper installation, or to
damage occurring during transit to or from the repairer andaltered or missing serial numbers.
•This Warranty does not apply to heating elements, bulbs or fuses within theproduct.
Your rights under this guarantee are additional to your statutory rights, which in turn arenot affected by
this guarantee.
Should you require after sales information or warranty assistance within UK & Ireland with
this product please go tohttps://www.micon-dist.com/.
Imported and Distributed by Micon Distribution Ltd.1a Hallstown Road, Ballinderry Upper, Lisburn
BT28 2NE. Ezee Glow Brand is exclusively owned byMicon.
DISPOSAL INFORMATION
Reduce, Re-use, Recycle
The left image indicates this product should not be disposed of with other household
wastes. To prevent harm to the environment and human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material resources. For
quick and easy recycling, return your used device, please use the return and collection
systems or contact the retailer where the product was purchased.