Figure IAUTO SAFETY SHUT-OTF WITH TIP-OVER
PROTEfiION:
This heqter is equipped with o polented, lechnologicolly-odvonted
sofef syslem fiol requires fie user lo resel fie heoler if ftere is
o polenliol overheol siluolion. When o polentiol overheol lem-
perolure is reoched, fie sy$em will outomolicolly shd fie heoter
off. lt ron only resume operolion when lhe user resels lhe unil.
TO RISTT THt HEAIER:
l. Unplug fte heoler ond woit l0 minules for lhe unil lo cool
down.
2. Afler fie l0 minules, plug fie unil in ogoin ond operole
normolly.
IIP-OVER PROTIfiION:
When fie heoler is oaidenlolly knocked over, il will oulomolitolly
shul off. Io reset, simply plore fte heoler in on upright posilion.
Pres fie M0DE builon ond operole normolly.
PRE-OPERATING INSTRUCTIONS
l. (orefully remove your heoler from ile box. (pleose sove the
corlon for off-seoson $oroge).
2. Plore heoler on firm level surfoce.
3. Avoid overlooding your circuit by nol using ofier high
wolloge opplionres in lhe some ouilel. Al 1500 Wolls, fiis
unil drows I 2.5 Amps.
NOIt: Ihe power light will remoin lil when plugged in.
AC(UTEMP PLUSTM DIGITA!. THERMOSTAT
Your heoter h equipped wilh on AauTemp PlusTM Digitol
Thermo$ol fiol ollows you l0 sel your heoler lo your precise
comfort level.
SETTING THT A((UIEMP PI.USTM IHERMOSTAT:
I . Pres fte Mode Bufton for monuol Hl power. Ihe heoler will
run ronlinuoudy ol I 500 Wolls.
2. Press ile Mode Bullon ogoin for monuol L0 power. The
heoler will run ronlinuously ol 1000 Wolls.
3. Pres fie Mode Bullon for o third time for Aulo Mode Hl
Power (AH) (l 500 Wolh) or pres ogoin for Aulo Mode L0
Power (AL) ( I 000 Wotts). ln either of these modes you moy
fien pres fte up, ond down builons lo reoch your desired
lemperolure
4. 0nce you hove selecled your desired lemperolure, lhe
disploy will relurn lo exisling room lemperolure. The heoler
will groduolly inrreose lhe room lemperolure until it hos
reoched your pre-sel lemperolure.
lf the unit will nol storl in fie AccuTemp Plus" mode, pleose
moke sure lhe "sel lemperolure" is higher thon lhe cunenl room
lemperolure.
NOIE: lt is normol for ile heoler lo cyde 0N ond ()tF os il
moinloins lhe presel temperoture. Io prevenl lhe unil from
cyding, you need lo roise fie ftermoslol selling. When the
presel lemperolure is reorhed, fie fon will run for 30 seconds
wilhoul heol. Ihis cool down process ensures on occurole ond
(onsislenl lemperolure reoding. lf you unplug fte heoler, you
will hove lo resel lhe Aaulemp PlusTM lhermostol ogoin by
following the obove in$ructions.
N0IE: Io shul fie unil off d ony lime, pres ond hold the mode
builon down for two setonds.
N0IE: Acculemp PlusTM hos memory. The Acculemp PlusTM
fiermoslol will remember lhe previous lemperolure selling ofter
fte unil hos been lurned off. However, if fie unit is unplugged,
fie ArcuTemp PlusTM lhermoslol will be resel ond wlll no longer
remember lhe previous lemperolure selling.
USING THE PROGRAMMABTT TIII|IIR
Arculgmp PlusTM lechnology ollows the user lo progrom lhe
heoler to rome on ol o presel lime, or lurn off ofler 0 sel omounl
of fime.
SEITING THE OTT TIMTR:
I . Seled fte Mode ond 0r lemperoture you wish fte heoter to
run in.
2. While the heoler is running, pres ond hold fie TIMP UP ond
TtMP D0WN huilons simuhoneously.
3. By presing the up ond down builons, progrom lhe heoter lo
turn off up lo l6 hours loler in inoemenls of I hour.
4. After selling fie fimer, the IED disploy will relurn lo show lhe
currenl room lemperolure.
5. Afler $e predelermined length of time hos posed, fie
heoter will oulomolkolly shul off.
SETTING THT ON IIMER:
l. While the heoler is off, pres ond hold the up ond down
bufions simultoneously.
2. By presing fie up ond down huflons, progrom lhe heoler lo
lurn on up lo I 6 hours in odvonce in inoements of I hour.
3. Afier fie presel lengft of ilme hos possed, the heoter will
oulomolicolly lurn on ol lhe lo$ mode selling lhot wos
progrommed. lf no progrom wos sel, lhe heoler will turn
on Aulo Mode Hl Power ol 75"F/24"(. for o presel lime of 2
hours.
NOT[: Anylime fte Mode button is presed while fie fimer is
oclivoled, fie limer funclion will be concelled ond need lo be
reset.
Figure 2
TEI\,4P DISPLAY
TEN,4P & TII\IE
INCREASE
TEI\,4P & TIME
DECREASE