Dimplex AF6 Series User manual
7203090000R01
Architectural Heaters
AF6/AS8 Series
GENERAL WARNINGS
Wiring procedures and connections should be in
accordance with the National Electric Code (NEC &
CEC) and local codes.
Do not install these heaters against combustible, low
Do not locate these heaters below any electrical conven-
ience receptacles.
-
HIGH TEMPERATURES -
the heater.
Recommendations for Locating Drapes and Furniture
near Heaters
-
mendations should be observed:
Hang drapes so that, in use, they extend below the1.
-
Hang drapes so that there is at least 3 inches between2.
3.
4.
material should not discolour nor distort dimensionally
(stretch or shrink) upon extended exposure (1000 hrs.) to
!NOTE:
!NOTE:
baseboard heater.
Installation Instructions
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should
1.
A heater has hot and arcing or sparking parts inside. Do2.
liquids are used or stored.
This heater is hot when in use. To avoid burns, do not let3.
when moving this heater. Keep combustible materials
4.
a bed where openings may become blocked.
-
lation or exhaust opening as this may cause an electric
SAVE THESE INSTRUCTIONS Wall Installation
1.
Remove the desired terminal box covers(s) and sup-2.
!NOTE: It is only necessary to remove the knockout(s)
the heater mounting location and supply wire location in
the wall.
Determine the correct mounting height and scribe or3.
snap a level line on the wall to maintain each heater back
plate in a horizontal alignment, when mounting.
!NOTE: Bottom air inlet heaters must be mounted a
4.
(provided by the customer) using the scribed line on the
wall to keep the heater level.
!NOTE:
the heater back panel to the high spots. This will avoid a
distorted appearance.
Proceed to the wiring instructions.
Floor Installation
1.
2.
Remove the desired terminal box cover(s) and supply3.
Figure 1)
1.5 in
(3.81 cm)
min
1.5 in (3.81 cm)
min
1.5 in (3.81 cm)
min
3 in (7.62 cm)
min
3 in (7.62 cm)
min
3 in (7.62 cm)
min
6 in (15.24 cm)
min
www.dimplex.com2
Wiring Diagrams
!NOTE: It is only necessary to remove the knockout(s)
the heater mounting location and supply wire location in
the wall.
4.
the pad with the heater. This will align the supply entry
knockout with opening in the pedestal pad.
!NOTE:
or more pedestals. The extra pedestals should be used
Place heater on the pedestal base(s) and tighten all
screws.
!NOTE:
the pedestal to aid in leveling the heater by loosening
!NOTE: Bottom air inlet heaters must be mounted a
Remove the terminal box cover and proceed to wiring
instructions.
Figure 1
Wiring Instructions
1.
above)
!NOTE: Supply wire entry is commonly made into one
Recommended minimum supply wire sizes are listed in the
table below:
MAXIMUM WATTS PER CIRCUIT USING 75 °C WIRE
(COPPER WIRE)
Rough in
Wire Size 120V 208V 240V 277V 347V 480V 600V
14 1440 2496 2880 3324 4164 5760 7200
12 1920 3328 3840 4432 5552 7680 9600
10 2880 4992 5760 6648 8328 11520 14400
Wire heaters and controls in accordance with the2.
appropriate wiring diagram.
!NOTE: Sample wiring diagrams are provided beside.
Wrap the supply ground wire around the green painted3.
ground screw & tighten.
!NOTE: When heaters are mounted end to end, remove
in the terminal box to ensure grounding continuity and to
protect the wiring.
through wiring and ground continuity. Do not exceed the
Electric Code.
© 2011 Dimplex North America Limited
3
CAUTION:
breaker panel.
CAUTION:
appliance contains no moving parts, little maintenance is
required beyond vacuum cleaning. It is, however, essential
and eventual damage. For this reason the heater must be
inspected regularly, depending upon conditions and at least
WARNING:
personnel.
Maintenance
Warranty
transportation or shipping costs in relation to such repair
whether expressed or implied including but not limited to
must be submitted in writing to the Service Manager, Dimplex
N1R 7G8, Canada.
1.
Prior to energization remove all construction dirt (plaster,2.
are protected against overheating by a built-in thermal cutout.
may cause the thermal overload protector to cycle the heater
to the room.
Operation
Terminal Box Volumes in Cubic Inches
Heater Style
Wide
Wide
4.
wires.
WARNING:
PANELS IN PLACE.
P
panel, and snap onto the plastic clips.
This manual suits for next models
1
Table of contents
Other Dimplex Heater manuals
Dimplex
Dimplex FPE 050E User manual
Dimplex
Dimplex AC45N User manual
Dimplex
Dimplex DPH1563 User manual
Dimplex
Dimplex GFP 100EW User manual
Dimplex
Dimplex BEETHOVEN User manual
Dimplex
Dimplex DECS2TN User manual
Dimplex
Dimplex WMCS712N User manual
Dimplex
Dimplex DTR 350 C User manual
Dimplex
Dimplex FXL12i User manual
Dimplex
Dimplex Comfort 2NC6 L Series User guide
Dimplex
Dimplex DHCER20WIFI User manual
Dimplex
Dimplex Q-Rad QRAD050RF User manual
Dimplex
Dimplex R23SH Series User manual
Dimplex
Dimplex DEUF2 User manual
Dimplex
Dimplex DHCER24M User manual
Dimplex
Dimplex OFRC20TI User manual
Dimplex
Dimplex EUH-B Series User manual
Dimplex
Dimplex RPX075N User manual
Dimplex
Dimplex LST050E User manual
Dimplex
Dimplex 3071 User manual
