MicrohDJ LED BLADEP186 MKIII User manual

USER MANUAL
Please read this user manual before using this product
LED BLADEP186 MKIII

Introduction
Thank you for purchasing the MICROH DJ LED BLADEP186 MKIII. For your
own safety and knowledge, please read this manual before installing or operating
this device. This manual covers the important information on installation and
applications. Please install and operate the xture according to instructions.
Meanwhile, please keep this manual for future reference.
Please carefully unpack the xture and check all ares to see if it was damaged
during transportation. Please check whether the following items are included in
the package:
Item Quantity
LED BLADEP186 MKIII xture 1
IR Remote 1
Blade Bracket 2
Power cord 1
User manual 1
Notify the shipper immediately and retain packing material for inspection if any parts
appear damaged from shipping or the carton itself shows signs of mishandling.
Save the carton and all packing materials. In the event that a xture must be
returned to the factory, it is important that the xture be returned in the original
factory box and packing.

Safety Warning
• Every person involved with the installation, operation and maintenance of this
device must be qualied.
• User/installer must follow the instructions of this manual.
• Unqualied persons must not open the housing cover and operate the device,
or the dealer will not accept liability for any resulting defects or problems.
• Protect the device against rain and moisture device with other electrical equipment.
• During move and installation, make sure the device is not stored with metal
parts and other tough materials.
• Always disconnect from the main power sources. Do not install or dismantle
when the device is powered on.
• The minimum distance between light output and the Illuminated surface must
be more than 50cm.
• The device must only be installed on a non-ammable surface. In order to
safeguard sufcient ventilation, please leave 50cm of free space around the
device. Note that heat-sensitive objects may be deformed or damaged by the
emitted heat of this xture.
• During operation, the housing may become very hot! Do not operate the device
for 15 minutes after switching off.
• The maximum ambient temperature Ta = 45°( must never be exceeded). The
maximum housing temperature Tb = 80°( must never be exceeded).
• This xture is for indoor use.
• Replace any visible cracked protective shields, lters, and lenses.
• The protective shields, lters, and lenses will require weekly cleaning as
smoke “cuid” tends to build up residues, reducing the light output very quickly.
CAUTION!
Never touch the device during operation!
The housing may heat up!
CAUTION!
Never look directly into light source,
as sensitive persons may suffer from an epileptic shock.
Caution!
• Unqualied person involved with installation, operation and maintenance of
this device is prohibited.
• lf any of the above mentioned problems happen, or unknown problems happen,
please contact manufacturer or distributor for assistance.

Mounting And Installing
Caution: for added protection, mount the xture in areas outside walking paths,
seating areas, or in areas were the xture might be reached by unauthorized
personnel. Before mounting the xture to any surface, make sure that the
installation area can hold a minimum point load of 10 times the devices weight.
Fixture installation must always be secured with a secondary safety attachment,
such as an appropriate safety cable. Never stand directly below the device when
mounting, removing, or servicing the xture.
Whether installing inverted on a truss or ceiling, or set on a at level surface be
sure this xture is kept at least 0.5m (1.5ft) away from any ammable materials
(decorations, etc.). Always use and install the supplied safety cable as a safety
measure to prevent accidental damage and/or injury in the event the clamp fails.
Mounting Points: Overhead mounting requires extensive experience, including
calculating working load limits. A knowledge of the installation material being
used, and periodic safety inspection of all installation material and the xture are
all imperative and should only be performed by a qualied technician. Improper
installation can result in bodily injury or damage.
Clamp Mounting: The MICROH DJ LED BLADEP186 MKIII provides a unique
mounting bracket assembly that integrates 2 brackets to be used to mount on
a truss or the oor. When mounting this xture to truss, be sure to secure an
appropriately rated clamp to the included bracket tted through the center hole.
As an added safety measure, be sure to attach at least one properly rated safety
cable to the xture.
Regardless of the rigging option you choose for your MICROH DJ LED BLADEP186
MKIII xture, always be sure to secure your xture with a safety cable. The xture
provides a built-in rigging point for a safety cable hanging bracket. Be sure to only
use the designated rigging point for the safety cable and never secure a safety
cable to a carrying handle.

Regardless of the rigging option you choose for your LED BLADE P186 MKIII,
always be sure to secure your xture with a safety cable. The xture provides a
built-in rigging point for a safety cable on the hanging bracket as illustrated above.
Be sure to only use the designated rigging point for the safety cable and never
secure a safety cable to a carrying handle.
Proper Usage: This product is for overhead mounting only. For safety purposes,
MICROH DJ recommends mounting lighting effect products on steady elevated
platforms or sturdy overhead supports using suitable hanging clamps. In all cases,
use safety cables. Obtain appropriate mounting hardware from your lighting vendor.
Operation Stipulation
• This xture can only be used indoors and it must be the consistent power condition
• Please pay attention to the installation and do not swing or mishandle the
xture in any way while using it.
• Please be sure the lamp is located in an area that isn’t too hot or damp. Before
installation make sure that you have 0.5m clearance between the xture and
the subject that is being illuminated.
• Please use appropriate and safe power line to connect the xture
• Please be sure to familiarize yourself with the lamp functions before operating,
since damage is mainly due to improper operation. Thus professional operation
is needed for this xture.
• Please use original packaging while transporting this unit.
• Please do not modify the lamp. Any unauthorized or nonprofessional operation
is not guaranteed by the factory, any breakdown and damage, the factory has
no obligation for maintenance.

DMX512 Control Data Connection:
This xture complies with international USITT DMX standards and can be used
with a 3 pin DMX connector. Plug in the 3 pin XLR cable to the female 3-pin XLR
output of your controller and the other side to the male 3-pin XLR input of the LED
battery par light. To connect the units to DMX, you must daisy chain the xtures
together as referred in the diagram below. Always end your DMX-512 connection
with a DMX terminator
For installations where the DMX cable has to
run a long distance, or is in an electrically noisy
environment, it is recommended to use a DMX
terminator. This helps in preventing corruption of
the digital control signal by electrical noise. The
DMX terminator is simply an XLR a 120 120 Ω
resistor connected between pins 2 and 3, which is
then plugged into the output XLR socket of the last
xture in the chain. Please see illustrations below:
Key Description
MENU: Access the menu
DOWN: “reduction key” or “key under the
selected”; decrease the value
function down menu.
UP: “add key” or “selection on the
key”; increase Lou = value
function, shift on the menu
ENTER: “OK button”; to determine the
function into the user selected
(that is to stop the ongoing
functions, run the function the
user selected items

Menu Display
Number Display Show Function
1 d001-d512 DMX mode
2 CHnd 4 or 8 channel selection
3Auxx/Soxx Au01-Au08: RGBW Colour mixing
Au09: Colour jumping
Au10: Colour fade
So01-So02: Sound mode
4St00 St00: Master to strobe
St00:-St16: Strobe slow to fast
5 SP00-SP16 Colour jumping and colour gradient speed
(slow to fast)
6 R000-R255 Red dimmer
7 G000-G255 Green dimmer
8 B000-B255 Blue dimmer
9 U000-U255 White dimmer
10 Iron-IroF Infrared remote control
IR Remote Controller Instruction
1. Press the “MENU” button, select “Iron ” then can use the IR remote
controller
2. Key Description:
FLASH = Auto run
STROBE = Strobe
FADE = Color gradient
SMOOTH = Sound control
Note:
The remote will work at a distance of 10ft
Press ON button on the remote to engage IR

DMX Modes
4CH Mode
Channel Value Function
1 000-255 Red Dimmer
2 000-255 Green Dimmer
3 000-255 Blue Dimmer
4000-255 White Dimmer
8CH Mode
Channel Value Function
1 000-255 Red Dimmer
2 000-255 Green Dimmer
3 000-255 Blue Dimmer
4000-255 White Dimmer
5000-014 No function
015-029 Single colour strobe
030-044 Multicolour strobe
045-255 Choose colour
6 001-209 No function
210-223 Red colour
224-255 Green colour
7 001-019 Blue Colour
020-039 White Colour
040-059 Red+White colour
060-079 Green+Blue+White colour
080-099 Colour change
100-119 Colour change
120-139 All bright
140-159 Multicolour Auto 01
160-179 Multicolour Auto 02
180-199 Sound 01
200-219 Sound 02
220-239 Sound 03
240-255 Sound 04
8 000-255 Strobe Speed for CH5 (slow to fast)
Note:
CH 1-5 will not work when CH6 is active
CH 1-6 will not work when CH7 is active

Features
• IR remote control
• 186 LEDs
Specications
Lamp/LED 186 x 10mm (42 Red, 42 Green, 42 Blue, 60 white)
Power input AC120V, 60Hz
Power Consumption 30W
Power connection IEC
Data connection 3 Pin XLR
DMX Modes Auto, Master/Slave, Sound, DMX, IR Remote
DMX Channels 4CH/ 8CH
Colour(s) RGBW
Dimmer Linear dimmer (0-100%)
Dimensions (mm) 200 x 75 x 200
Weight 1Kg

PLEASE NOTE:
All information for this product is subject to change without notice!
Maintenance and Cleaning
The following points have to be considered during the inspection:
1. All screws for installing the device, or parts of the device must be tightly
connected, and must not be corroded.
2. There must not be any deformations on the housing, colour lenses, xations or
installation spots (ceiling, suspension, trussing).
3. Mechanically moved parts must not show any traces of wearing and must not
rotate with unbalances.
4. The electric power supply cables must not show any damage, material fatigue
or sediments.
Further instructions depending on the installation spot and usage must be handled
by a skilled installer or technician. Any safety issues must be resolved.
CAUTION!
Disconnect xture before servicing.
In order to keep the xture in good condition and extend the life, we suggest regular
cleaning to the xture.
1. Clean the inside and outside lens each week to avoid the light output from
darkening due to accumulation of dust, dirt, etc.
2. Clean the fan each week.
3. A detailed electrical check by an approved technician every three months is
advised. Ensure the circuit contacts are in good condition, and prevent from
overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint-free
cloth. Never use alcohol solvents.
There are no serviceable parts inside the device. Please refer to the instructions
under “Installation Instructions.”
Should you need any spare parts, please order genuine MICROH DJ parts from
your local dealer.
CAUTION!
Take care using this equipment! High voltage risk of electric shock!

For more information please contact:
www.microhdj.com
[email protected]
905.428.9062