Micron Xccela Flash MT35X User manual

Micron®Xccela™Flash Quick Start Guide for ZedBoard™
This development kit (including daughterboard with FPGA software code) contains confidential
information of Micron Technology, Inc. It is provided for evaluation purposes only and is not
authorized or licensed for any other use. This development kit is provided “as is” without any
warranties of any kind whatsoever. By your acceptance and use of this development kit, you
acknowledge, agree, and accept that Micron expressly disclaims all warranties, whether
written or implied by law, including warranties as to title, merchantability or fitness for a
particular purpose, warranties against infringement of intellectual property rights of a third
party, warranties arising by custom, trade usage, course of dealing, or otherwise. Micron
makes no warranty of any kind, and hereby disclaims any warranty, that the development kit
will meet your or any other person’s requirements, achieve any intended result, or be secure,
accurate, complete, free of harmful code or error free. Any open source components or other
third-party materials are provided “as is” and without any representation or warranty from
Micron.
Micron®Xccela™Flash (MT35X)
Development Kit
Quick Start Guide
for ZedBoard™

CCM005-1718347970-10454
micron_xccela_zedboard_qsg.pdf Rev 0.1 4/19 2
Micron®Xccela™Flash Quick Start Guide for ZedBoard™
Introduction
This guide provides the information needed to connect, boot, and access
configuration commands for Micron’s Xccela Flash MT35X memory
(packaged on a TBGA-24B installed on a dedicated daughterboard) to a
ZedBoard evaluation and development board.
Quad-SPI NOR (MT25Q) Instructions: The daughterboard also supports
Micron’s Quad-SPI NOR (MT25Q) memory. Follow these instructions, except
download different software (config-MT25Q_1.8.zip or config-MT25Q_3.0.zip)
and user manual (ZedBoard User Manual–Quad SPI NOR Flash (MT25Q).pdf).
Items Required
•Xccela Flash MT35X (contact your local Micron representative for samples)
•ZedBoard
•24-ball TBGA daughterboard
•SD card with configuration files
•Universial serial port tool
•PC with Microsoft Windows®7 or higher
Related Documents
•Micron®Xccela™Flash (MT35X) Development Kit User Guide for
ZedBoard™
•Micron®Quad SPI NOR (MT25Q) Development Kit User Guide for
ZebBoard™
Questions about the development kit can be sent to [e-mail].

CCM005-1718347970-10454
micron_xccela_zedboard_qsg.pdf Rev 0.1 4/19 3
Micron®Xccela™Flash Quick Start Guide for ZedBoard™
Download the Software and
Connect the Board
1 Download the software (config—MT35X_1.8.zip for MT35XUseries or
MT35X_3.0.zip for MT35XL series) and the user manual (ZedBoard
User Manual—Xccela Octal SPI NOR Flash (MT35X).pdf) from
www.xccela.org/resource.
2 Unzip the files onto an SD card.
The software (config—MT35X_1.8/3.0.zip) contains the files needed to boot
up the ZedBoard. These files must be stored in a FAT32-formatted SD card:
Linux kernel, Ramdisk rootfs, device tree, boot images and testing bench-
related files.
NOTE: Do not rename the boot files; these file names must remain as
displayed.
3 Attach the daughterboard to the ZedBoard.
Daughterboard
ZedBoard

CCM005-1718347970-10454
micron_xccela_zedboard_qsg.pdf Rev 0.1 4/19 4
Micron®Xccela™Flash Quick Start Guide for ZedBoard™
Set Jumpers and Connections
To boot the ZedBoard, several jumpers and connections must be configured as
described below. Follow these instructions before powering on the board.
1 Connect J2.
2 Configure JP7, JP8, JP9, JP10 and JP11 as follows:
Jumper
JP7
JP8
JP9
JP10
JP11
Setting
GND
GND
3V3
3V3
GND
3 Set J18 to 1V8 or 3V3 according to the operating power of your SPI-
NOR device.

CCM005-1718347970-10454
micron_xccela_zedboard_qsg.pdf Rev 0.1 4/19 5
Micron®Xccela™Flash Quick Start Guide for ZedBoard™
Power On the ZedBoard
1 Plug in the SD card, USB cable (for the serial port), and DC adapter as shown below.
2 Switch on power by SW8.
3 If this is the first time inserting the USB port, the driver automatically downloads
and installs. After the driver installs successfully, the USB port maps to a serial
port (for example, COM11).
4 Open the serial port tool, and then configure the port number to the USB serial
port mapped in the previous step (for example, COM11).
5 Set the baud rate to 115200.

CCM005-1718347970-10454
micron_xccela_zedboard_qsg.pdf Rev 0.1 4/19 6
Micron®Xccela™Flash Quick Start Guide for ZedBoard™
6 If this is the first time booting the ZedBoard, run the following two commands to
set up the system boot environment, and then power down the board. Skip these
three steps if you’ve previously booted the ZedBoard.
•Press any key when the message Hit any key to stop autoboot appears.
•env default -f -a
•env save
7 Power on the ZedBoard.
When the XCCELA>> prompt appears after the Micron welcome screen (it may take
a few seconds), the system boots successfully and enters the SPI NOR test bench.

CCM005-1718347970-10454
micron_xccela_zedboard_qsg.pdf Rev 0.1 4/19 7
Micron®Xccela™Flash Quick Start Guide for ZedBoard™
ZedBoard OLEDs after boot
MT35X logo indicates the DUT
is under testing
If another vendor’s memory is detected (instead of Micron’s Xccela flash
memory), or if no memory is detected, the system hangs at the boot stage
with the following message:

CCM005-1718347970-10454
micron_xccela_zedboard_qsg.pdf Rev 0.1 4/19 8
Micron®Xccela™Flash Quick Start Guide for ZedBoard™
Command Help
1 Type HELP and then press enter to obtain all supported commands for
Micron’s Xccela SPI NOR device.
2 Type -H and then press enter to obtain command details.
(For example, type FRD -H to obtain information for the page program
command.)
3 For additional details, see the user manual.
No hardware, software or system can provide absolute security under all conditions. Micron assumes no liability for lost, stolen or corrupted data
arising from the use of any Micron products, including those products that incorporate any of the mentioned security features. ©2019 Micron
Technology, Inc. All rights reserved. All information herein is provided on an “AS IS” basis without warranties of any kind. Micron, Xccela, the
Micron logo, and all other Micron trademarks are the property of Micron Technology, Inc. All other trademarks are the property of their respective
owners. Products are warranted only to meet Micron’s production data sheet specifications. Products, programs and specifications are subject to
change without notice. Dates are estimates only. Rev. A 4/19 CCM005-1718347970-10454