Microchip Technology IS2083 Series User manual

IS2083
IS2083 SDK Debugger User's Guide
Introduction
This document describes how to use the SEGGER JLINK debugger to enable software debugging of 8051 MCU core
that is part of the IS2083BM. The SEGGER debugger makes use of IS2083BM 2-wire JTAG interface to download
8051 firmware images into IS2083BM SQI flash. It then controls the IS2083BM SQI CPU register to provide
debugging features. The following chapters describe the software and hardware prerequisites, setup and procedure
to enter the Debugging mode.
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 1

Table of Contents
Introduction.....................................................................................................................................................1
1. Quick References....................................................................................................................................3
1.1. Reference Documentation............................................................................................................3
1.2. Software Prerequisites................................................................................................................. 3
1.3. Hardware Prerequisites................................................................................................................3
2. Software Setup........................................................................................................................................6
2.1. Keil μVision Setup........................................................................................................................ 6
2.2. SDK Settings.............................................................................................................................. 10
3. Hardware Connection............................................................................................................................11
3.1. J-Link Probes Connection.......................................................................................................... 11
4. Start Debugging.................................................................................................................................... 15
4.1. Enabling Debug Mode................................................................................................................15
5. Document Revision History...................................................................................................................18
The Microchip Website.................................................................................................................................19
Product Change Notification Service............................................................................................................19
Customer Support........................................................................................................................................ 19
Microchip Devices Code Protection Feature................................................................................................ 19
Legal Notice................................................................................................................................................. 19
Trademarks.................................................................................................................................................. 20
Quality Management System....................................................................................................................... 20
Worldwide Sales and Service.......................................................................................................................21
IS2083
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 2

1. Quick References
1.1 Reference Documentation
Please go to http://www.microchip.com/IS2083 or http://www.microchip.com/BM83 to get the following documents.
•IS2083 Bluetooth® Stereo Audio SoC Data Sheet
•BM83 Bluetooth® Stereo Audio Module Data Sheet
•BM83 Bluetooth® Audio Development Board User's Guide
•IS2083 SDK User's Guide
1.2 Software Prerequisites
• IS2083 Software Development Kit
• isUpdate tool
• Please refer to the IS2083 SDK User’s Guide Section 1.2 to know what Keil® μVision® version should be used.
Furthermore, please be sure your PK51 license is valid in the support period. If your license expires on or before
the support period, Keil C51 may not allow you to use the debugger support. It depends on if your license
expiration date is on or before the C51 release date. For example, C51 9.59 released in May 2018. If your
license expired before that, you cannot use the debugger with C51 9.59. On the other hand, if your license
expired after May 2018, you can still use the debugger support. For example, the figure below shows that this
license has expired, but it can still work with C51 9.59 because it is after May 2018.
– The following DLL files enable debugging in the IS2083BM using Keil μVision:
• JLinkARM.dll
• JLinkIS2083.dll
– Initsession.ini – this file stops the Keil μVision at the first execution of SDK.
Note: The DLL files and Initsession.ini file are available in the following folder:
release-package at http://www.microchip.com/IS2083 or http://www.microchip.com/BM83.
• J-Link Commander (folder path: \Software\Debugger Support\Commander)
– An executable command prompt to check if J-Link probes can communicate with the IS2083BM.
1.3 Hardware Prerequisites
• SEGGER J-Link Debug Probe
IS2083
Quick References
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 3

Figure 1-1. J-Link Debug Probe
– J-Link PRO, J-Link ULTRA+, J-Link PLUS and J-Link BASE.
• BM83 EVB
– BM83 EVB provides a two-wire JTAG interface to communicate with the IS2083BM.
• J-Link 6-pin adapter from Microchip
IS2083
Quick References
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 4

Figure 1-2. J-Link 6-pin Adapter
IS2083
Quick References
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 5

2. Software Setup
This section describes the setup procedure of Keil uVision and IS2083 SDK to work with the debug probes.
2.1 Keil μVision Setup
This section describes the step-by-step procedure for Keil μVision setup. The user needs to first set up μVision and
connect to J-Link debug probes and later to the BM83 EVB. See 3.1 J-Link Probes Connection.
2.1.1 File Settings
Visit the Keil website to download and install the required Keil C51 (See IS2083 SDK User Guide, Section 1.2,
Software Prerequisites for the latest SDK Keil supported version.).
IS2083 SDK requires a specific Keil μVision tool to compile and operate with J-Link probes. The .dll files
customized for SEGGER J-Link debugger allows Keil μVision to communicate with the IS2083BM through J-Link
probe.
Note: After Keil μVision installation, ensure that it is not running.
Keil C51 v9.59 requires the following steps, 1 to 3 for file settings. The version v9.60 and above contains the DLL
files. Perform only step 3 for Keil C51 v9.60 and above.
Perform the following steps for the setup:
1. Go to C:\Keil_v5\ and use the text editor to open the TOOLS.INI file.
2. Insert the text TDRV10=BIN\JLinkIS2083.dll (J-Link / J-Trace IS2083 Driver) into the file as
shown below:
Figure 2-1. TOOLS.INI
3. Go to C:\Keil_v5\C51\BIN and copy the following files from the debug package to the directory:
– JLinkIS2083.dll
– JLinkARM.dll
2.1.2 Debug Settings
After verifying the J-link connection and Keil file settings, unplug and plug in the power cord to reset the IS2083BM.
This turns the J-Link LED to steady green.
Perform the following steps for debug settings:
1. Launch Keil μVision and double click MSPKv2_Application_IS2083B.uvproj and Keil uVision automatically
loads these SDK project files:
– MSPKv2_App_Pbap
– MSPKv2_App_MSPK
– MSPKv2_App_Basic
IS2083
Software Setup
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 6

– MSPKv2_App_MSPK_Debug
2. For each of the projects, right-click the "Options for Target.”
Figure 2-2. Build Target
3. In the Debug tab, select the highlighted parameters for setup. Replace S8051.DLL with -cIS208x and
DP51.DLL with -pIS208x. Load the InitSession.ini file in “Initialization File” and select the “Load
Application Setup” checkbox.
IS2083
Software Setup
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 7

Figure 2-3. Options for Target
4. Click the Settings button.
5. Select “Speed” as 12000 kHz and deselect the checkbox "Compare before download". Click OK.
IS2083
Software Setup
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 8

Figure 2-4. Debug Settings
6. To build the application and start a debug session, click
. Keil μVision is now ready to debug the IS2083BM device.
IS2083
Software Setup
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 9

Figure 2-5. Debugging Session
2.2 SDK Settings
The 2-wire JTAG debug port (i.e. P1_2 and P1_3) on IS2083BM is multiplexed with I2C function. Before debugging,
the user must enable the buildoption ENABLE_JTAG_DEBUG. This enables SW I2C and disables Low Power mode
for the debugger to run properly. The user can select MSPKv2_App_MSPK_Debug project target, which includes
ENABLE_JTAG_DEBUG buildoption.
ENABLE_JTAG_DEBUG uses SW I2C port (P2_3 and P2_6 by default) instead of HW I2C. SDK enables Low Power
mode, which turns off the debugger clock and then disconnects the debugger. ENABLE_JTAG_DEBUG is used to
disable the Low Power mode to avoid this. Refer to the IS2083 Bluetooth® Stereo Audio SoC Data Sheet for more
details on JTAG program and debug feature.
For information on which SDK features are included in MSPKv2_App_MSPK_Debug project, see the IS2083 SDK
User's Guide, Section 2.2, and Table 2-1.
Figure 2-6. Target Build
IS2083
Software Setup
© 2019 Microchip Technology Inc. User Guide DS50002892A-page 10