Middle Atlantic Products TOR-2-20SP User manual

I-00101 Rev F
TOR Series
Tilt Out Wall Rack
Instruction Sheet
THANK YOU
Thank you for purchasing the TOR-X-20SP. Please read these instructions thoroughly before
installing / assembling this product.
UL
R
C US
LISTED

Page 2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING ALERTS YOU TO A SITUATION
THAT COULD RESULT IN SERIOUS PERSONAL INJURY
OR DEATH.
!
!
IMPORTANT WARNINGS AND CAUTIONS!
WARNING! Failure to read, understand and follow the following information can result in serious personal injury, damage to the
equipment or voiding of the warranty.
NOTE: A NOTE IS USED TO HIGHLIGHT PROCEDURES
PERTAINING TO THE INSTALLATION, OPERATION OR
MAINTENANCE OF THE PRODUCT.
CAUTION: A CAUTION ALERTS YOU TO A SITUATION
THAT MAY RESULT IN MINOR PERSONAL INJURY OR
DAMAGE TO THE PRODUCT AND / OR PROPERTY.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with dry cloth.
• Only use attachments/accessories specified by the manufacturer.
CAUTION: All installation and assemble steps must be performed by qualified personnel.
CAUTION: Ensure that the wall/floor has a structural load capacity that will support the weight of the cabinet fully loaded with
equipment.
CAUTION: Some parts of the enclosure system may not be effectively bonded to the Protective Earth Terminal (PET). If these parts
need to be bonded to the PET it should be done in accordance with Article 250 of the National Electrical Code.
CAUTION: Power cord(s), for fans or other accessories, need to be secured to ensure that they are routed away from pinch points
and moving parts.
CAUTION: Do not attempt to unload or move the enclosures alone. Make sure to have sufficient amount of personnel and
equipment to safely move this product.
CAUTION: The following parts are not effectively bonded to the protective earth terminal: Rackrails, lace bars, Lever Lock™,
shelving, baffles, blank panels, and cable management equipment. If any part needs to be bonded to the protective earth terminal
it shall be done in accordance with Article 250 of the National Electrical Code.
!
!
!
!
!
!
!
CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY AND CONFORM TO THE UL LISTING THESE
MOUNTING INSTRUCTIONS MUST BE FOLLOWED AND PROPER WEIGHT CAPACITIES MUST BE OBSERVED.
!
CAUTION: Maximum weight capacity is 100 lbs.
!

BACKPAN
LIFT
ROTATE
Page 3
Tools needed:
- Socket wrench set
- Power Drill and bit set
1) Disassembly required prior to mounting. Open door on faceplate. To do this, door must be slightly
lifted and opened to the service position (105º) (See FIGURE A)
2) Remove 6 nuts that secure the faceplate to backpan and remove faceplate. (See FIGURE B)
FIGURE A
FIGURE B
DECORATOR STYLE
KNOCKOUT
UCP
PANEL
FACEPLATE
CLAMP
3) Using customer supplied mounting hardware specified
below (6 places), mount backpan to wall. (see FIGURE C)
Block Wall Installation:
1) 5/8" pilot hole
2) 1/4" X 2" toggle bolt and washer
Wood Stud Wall Installation:
1) 1/8" pilot hole in center of stud
2) 1/4” X 2" lag bolt and washer
4) Re-assemble faceplate to backpan by re-using 6 nuts.
(See FIGURE B)
FIGURE C
16.00
[406]
24.60
[625]
MOUNTING
HOLES
ASSEMBLY
NOTE: Do not use 8.5" x 8.5" square
knock-out in backpan when flush mount
installed. Knock-out must remain in place.

Page 4
NOTE: Middle Atlantic Products provides a clamp for use on non-rackmount equipment. On equipment
that is rackmounted, clamp is not required and can be discarded.
Choose a desired location for clamp and assemble clamp to ears using screws and nuts provided
(See FIGURE D). Slide clamp brackets securely down on equipment and tighten. Adjust stop bars to
secure rear of equipment
FIGURE D
CLAMP
BRACKETS
STOP
BARS
EARS
CLAMP ASSEMBLY
OPTIONAL ACCESSORY:
UNIVERSAL CONNECTOR PANEL
For Middle Atlantic Products UCP modules (used to mount commonly used connectors), see
middleatlantic.com for details. To install, remove blank panel and install re-using hardware provided.
NOTE: Some of the UCP panels may need to be mounted on the surface of the faceplate.

Page 5
GROUNDING AND BONDING
Protective Earth Terminals (PET) are located in backpan of the wall rack. These terminals are marked with the symbol
Wall rack parts, center section and door, contain or are provided with bonding points for connection to the backpan / PET.
Protective earth and bonding connections shall be in accordance with Article 250 of the National Electric Code.
OPTIONAL PROTECTIVE EARTH TERMINAL KIT: #PET-K-WRP/S
PARTS LIST
• Backpan bonding wire [12 Gauge Wire
(#10 ring terminal to 1/4” ring terminal] 10”]
• Door bonding wire [12 Gauge Wire
(#10 ring terminal to #10 ring terminal) 5”]
• Locking Nut 10-32
QTY
(1)
(1)
(3)
(3) (1) (1)
1) Attach backpan bonding wire from 10-32 backpan protective earth terminal (PET) to door
bonding point.
NOTE: The main protective earth ground needs to be the first terminal placed on the PET and this
terminal needs to be secured on its own with a nut. The bonding wire for the center section can
be added to the PET after securing the nut for the main ground.
2) Attach door binding wire to access door bonding stud (10-32) and door bonding stud (10-32)
using hardware provided (included).
Door Bonding Stud
(10-32)
Access Door
Bonding Stud
(10-32)
FIGURE E

WARRANTY
Middle Atlantic Products (the "Company") warrants the TOR-X-20SP to be free from defects in
material or workmanship under normal use and conditions for the lifetime of the product.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of
and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products
purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this
warranty does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone]
International Voice [phone] - Fax [phone]
middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice 613-836-2501 - Fax [phone]
middleatlantic.ca - [email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
Page 6