Middle Atlantic Products SFR Series User manual

I-00040 Rev G
SFR Series
Swing Frame rack
Instruction Sheet
THANK YOU
Thank you for purchasing the SFR Series Swing Frame Rack. Please read these instructions
thoroughly before installing/assembling this product.
PRODUCT FEATURES
- Open back design can be mounted over existing conduit or equipment
- Heavy-duty 100 lb. weight capacity; will not sag when properly installed
- Swinging rack can be reversed to open to either side

PARTS
DIMENSIONS
MOUNTING PLATE QTY
1A
BRACE
NOTE: SFR-XX-12 models have specific top and bottom
braces. The top brace is labeled
QTY
2C
PART
PART
PIVOT BOLTS QTY
2E
PART
GATE QTY
1B
PART
BRACE SCREWS
45º Open Position
QTY
2D
HARDWARE KIT 91-00183
PART
0
Maximum Open Position Closed Position
35.67"
29.67"
18.2"
12.2"
19.6"
20.7”
25.0"
29.2”
16" Mounting
center
90
Page 2
NOTE: The multiple dimensions shown are in the following format: SFR-XX-12/SFR-XX-18/SFR-XX-24
Component
depth
10”
16”
22”
41.67"
24.2"
Minimum clearance
required when using 12”,16" or 22”
deep components

INSTALLATION
NOTE: All hardware is to be supplied by the
customer unless otherwise specified
1) Determine swing of the rack prior to installation.
2) Secure mounting plate (A) to wall using
the top keyhole. (FIGURE A)
TOP
KEYHOLE
LEVEL
3) Level mounting plate. (FIGURE B)
TOOLS REQUIRED
- 3/8" Wrench or #3 Phillips Driver (FOR PART D)
- 9/16" Wrench (FOR PART E)
- Level
- Square
FIGURE A
FIGURE B Page 3

INSTALLATION (CONTINUED)
BOTTOM
KEYHOLE
CENTER
KEYHOLE
4) Install hardware in bottom keyhole.
(FIGURE C)
5) Install hardware in center keyhole.
(FIGURE C)
6) Install hardware in fixed holes
for extra stability.
(FIGURE D)
FIGURE C
FIXED HOLE
FIXED HOLE
FIGURE D
Page 4

INSTALLATION (CONTINUED)
7) Install top brace (C) to mounting plate (A)
using brace screw (D). (FIGURE E)
IMPORTANT NOTE: SFR-XX-12 top brace (labeled top) must have the
three holes facing the mounting plate to ensure proper installation
(FIGURE F)
8) Square mounting plate. (FIGURE G)
9) Install top brace to wall.
FIGURE E
FIGURE F
D
C
A
FIGURE G
SQUARE
Page 5
D

10) Install bottom brace (C) to mounting plate (A)
using brace screw (D). (FIGURE H)
IMPORTANT NOTE: The SFR-XX-12 bottom brace must have the three holes
facing the mounting plate to ensure proper installation (FIGURE J)
FIGURE H
FIGURE J
FIGURE K
C
D
D
A
SQUARE
11) Square mounting plate. (FIGURE K)
12) Install bottom brace to wall.
INSTALLATION (CONTINUED)
Page 6

13) Install gate (B) to mounting plate (A)
using pivot bolts (E). (FIGURE L)
IMPORTANT NOTE: Tighten pivot bolts (E). DO NOT OVERTIGHTEN
NOTE: Gate latches to the mounting plate
on the top and bottom (FIGURE M)
FIGURE L
FIGURE M
E
E
LATCH
NOTE: Rackrail on gate (B) must face out
B
INSTALLATION (CONTINUED)
Page 7

WARRANTY
Middle Atlantic Products, (the "Company") warrants the SFR Series Swing Frame Rack
to be free from defects in material or workmanship under normal use and conditions for
the lifetime of the product.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return
of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the
products purchased, or any part or parts thereof, which the Company has determined to be
defective after inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this
warranty does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone]
International Voice [phone] - Fax [phone]
middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice 613-836-2501 - Fax [phone]
middleatlantic.ca - [email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 Registered Company.
Page 8
30% Recycled Paper