Middle Atlantic Products MMB Series User manual

In s tr u c t io n S h e e t
MMB Series Md n it d r Md u n t
MMB-1X1C, MMB-1X2C, MMB-2X1C, MMB-2X2C, MMB-3X1C
MOUNTING THE BASE
REFER TO PARTS LIST ON PAGE 3
Clamp Mounting FIGURE A)
1) Loosen screw with 3/16” hex key.
2) Fit vertical plate onto work surface or edge of desk.
NOTE: Plate must contact edge of work surface.
3) Tighten screw with 3/16” hex key.
Grommet Mounting FIGURE B)
1) Disassemble vertical plate FIGURE A) from base.
2) Place base over hole in work surface.
3) Place grommet plate beneath work surface
and attach to base with bolt.
ARM ATTACHMENT FIGURE C, D, E)
1) Secure arm support ring to pole at desired height.
2) Snap pole joint bushing into arm assembly may
be inside monitor mount knuckle).
3) MMB-1X1C, MMB-1X2C ONLY: Mount arm
assembly on pole at desired height and tighten
set screw with 1/8”hex key.
4) Snap trim ring onto arm assembly.
5) Insert cables into cable managers.
6) MMB-3X1C ONLY: Secure center monitor
mount knuckle as described above.
Trim Ring
Arm Assembly
Single)
Set Screw
Pole Joint
Bushing
Arm
Support
Ring
Pole
FIGURE A
Bolt
FIGURE B
Cable
Managers
FIGURE E
FIGURE C
Pole Joint Bushing
Arm Support Ring
:— Pole
FIGURE D
Middle Atlantic Products
I-00638 Rev A

MONITOR ATTACHMENT FIGURE F)
Quick
Connect
VESA
Mount
Arm
Assembly
I
Screws 4) FIGURE F
1) Attach quick connect vesa mount to monitor
using the appropriate screws short or long).
2) Slide quick connect bracket onto arm
assembly until it clicks into place.
NOTE: Depress tab on base of quick connect
bracket to release from arm assembly.
ADJUSTMENTS
Adjusting the Height Adjustable Segment
1) With the monitor mounted to the arm, move the monitor
through the height range; Ensure the arm will hold the
monitor in the position in which you placed it.
2) If the monitor drops or rebounds upward, adjust the
tension screw at the back of the arm segment with
1/8” hex key. FIGURE G) FIGURE G
Using the Height Adjustable Cable Manager FIGURE H)
1) Remove cable manager by pinching at release points.
2) Lay cables in cable manager.
3) Snap cable manager back into place. Note text
indication "FRONT” inside cable manager.
Release Points
FIGURE H
Adjusting the Torque FIGURE I)
1) Remove joint cap from the top of the joint using a small
flat head screw driver.
2) Unscrew the cable manager from the bottom of the joint.
3) Holding the bolt in the top of the joint with a 9/16” socket,
use a second 9/16” socket on the nut in the bottom of
the joint to adjust the torque setting.
4) Replace cap and reassemble cable manager.
Page 2
Joint Cap
Cable Manager
FIGURE I

PARTS LIST
NOTE: Depending on your model, all items shown below may not be present in your kit.
Pole Assembly Pole Joint Bushing Arm Support Ring
With Base And
Vertical Plate
Trim Ring 1) 3/16” Hex Key
1) 1/8” Hex Key Monitor Mount
Knuckle
Quick Connect
VESA Mount Arm Assembly
Single) Arm Assembly
Double) Screw Kit
Qty 4 Short, 4, Long) Grommet Plate
3/8-16x4” LG
Hex Bolt
Page 3

/ \
Middle Atlantic Products
whatgreat systems are built on™
middleatlantic.com ■ 800.266.7225
V____________________________________________J
WARRANTY
Middle Atlantic Products, Inc. the "Company") warrants the MMB Series Monitor Mount to be free from defects in material or workmanship
under normal use and conditions for a period of 3) years from date of shipment by the Company.
The Company's entire liability to the purchaser, and the purchaser's or any other party's) sole and exclusive remedy, under this warranty
shall be limited, at the Company's option, to either a) return of and refund of the price paid for, or b) repair or replacement at the
Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or
any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly,
installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF
THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO
EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone] / International Voice [phone] - Fax [phone]
middleatlantic.com - [e-mail]
Middle Atla tic Ca ada
Voice 613-836-2501 - Fax [phone] / middleatlantic.ca - [e-mail]
Factory Distributio
USA: NJ - CA - IL Canada: ON - BC
At Middle Atla tic Products we are always liste i g. Your comme ts are welcome.
Middle Atla tic Products is a ISO 9001 a d ISO 14001 Registered Compa y.
Page 4