MidNite Solar MNPV6 Reference guide

2
1
4
3
5
8
7
3
6
Step 1.
Rivet the dinrail #3-043-1 to
the chassis #3-040-3.
Step 2.
Lay the black paper insulator
#5-022-1 down with the diago-
nal corner to the upper center.
Step 3.
Screw down the negative
busbar insulators #5-015-2
using #6-007-1 screws. Alumi-
num chassis strips easily.
Don’t over tighten.
Step 4.
Snap on the left busbar on to
the negative insulators.
Step 5.
Screw down the right side
busbar using #6-037-1 screws
and #6-017-1 lock washers.
Step 6.
Loosen up the second large
inset screw from the top of the
right side busbar.
Step 7.
Place large black paper insula-
tor #5-021-1 in the top portion
of box around the dinrail.
Step 8.
Place inside labels #10-008-1
MNPV6 Procedure
May 30, 2011
#5-022-1
#5-021-1
#5-021-1
Lock washer
#10 internal tooth
#6-017-1
Lock washer
#10 internal tooth
#6-017-1
Pan head screw 10 x 3/8
#6-007-1 Pan head screw
10-32 x 3/8
#6-036-1
Pan head screw
10-32 x 5/16
#6-037-1

Step 9.
Place large label on the right
outside of the box.
The side label #10-008-1
needs to have the model
number checked, in this
case, MNPV6, which quarter
of the year, in this case, the
second quarter (Q2) and the
last two digits of the year
the unit was assembled,
(11).v
9
Labels #10-008-1

10
10
11
11
Step 10.
Place the white wire tie #6-
014-2 through the second
large inset screw hole on the
right side busbar.
Step 11.
Using a wire tie, secure the
plastic hardware bag, slip-
ping the busbars in the bag
under the dinrail and pulling
the wire tie, snug.
Fuse adapter #5-035-1
4 x 6 Plastic bag
#9-048-2
Fuse busbar #3-079-1
Breaker busbar #3-079-1
2x3.2 Plastic bag
#9-111-1
Two 1/0 12 Lug
#9-075-1
Two pan head screw #6-059-1
10-32 x 1/4
Lock washer
#10 internal tooth
#6-017-1
HARDWARE KIT

12
12
Step 12.
Attach the label #10-008-1
on the inside of the cover
#3-041-2. Make sure the
cover is upside down and
the label is right side up.

13
13
14
Step 13
Attach the deadfront secur-
ing the bottom first and then
snapping the top in.
Step 14
Make sure the note #10-
012-1 is in place under the
cover. The screw should go
through the note to hold it in
place.
Note #10-012-1

Step 15.
Attach the cover #3-041-2,
snapping in the top.
Step 16.
Attach the MidNite badge
#5-029-1 in the lower right
hand corner.
Step 17.
Slide the rest of the labels
#10-008-1 under the cover.
Step 18.
Screw down the cover using
a # 6-017-1 lock washer and
a #6-017-1 screw. Make sure
that the note is in place
before the screw is applied.
15
15
16
16
17
17
18
18

Step 19.
Put unit in plastic bag that
the unit originally shipped in.

Step 20.
Use box #9-078-1. It will have MNPV6 on the side or end of
box. Fold the two end flaps down. Then fold the side flap
with no graphics and place glue as shown above. Fold the
remaining flap down and press it firmly for a few seconds to
allow the glue to harden.
NOTE: The image is a box for the MNPV3 but the procedure
is the same for the MNPV6 box.
Box #9-078-1

21
21
21
21
Step 21.
Put padding corners in the
bottom of the unit.

Step 22.
Put manual #10-010-1 in
box.