Miele CVA 7775 User manual

11823040-02
Installation
*INSTALLATION*
Fresh water connection
Risk of injury and appliance
damage if appliance is not
connected properly.
Failing to connect the appliance
properly can result in personal injury
and/or material damage.
The appliance may only be
connected to the fresh water
connection by qualified specialists.
Risk to health and risk of
damage due to contaminated water.
The quality of the incoming water
must conform to the requirements for
drinking water in the country where
the coffee machine is being used.
Connect the coffee machine to the
drinking water supply.
Connection to the water supply must
comply with the applicable
regulations in the country where the
appliance is being installed. All
appliances and systems used to
supply water to the coffee machine
must also comply with the applicable
regulations in the respective country.
Connect the coffee machine directly
to a fresh water pipe.
Avoid connecting the coffee machine
to a water inlet in which the water
might stagnate. Otherwise, the
flavour of the drinks could be
impaired.
The coffee machine meets the
requirements of IEC61770 and
EN61770.
The coffee machine may only be
connected to a cold water supply.
The water connection pressure needs
to be between 100and 1,000kPa
(1and 10bar).
A faucet must be provided between the
stainless steel hose and the domestic
water supply to ensure that the water
supply can be cut off if necessary.
Make sure the faucet remains easily
accessible once the coffee machine has
been installed.
Connecting the stainless steel hose
to the coffee machine
Only use the stainless steel hose
supplied. The stainless steel hose
must not be shortened, extended, or
replaced by a different hose.
The stainless steel hose must only
be replaced by an original Miele part.
The food-grade, stainless steel hose
is available to order from the Miele
online shop, from Miele Service, or
from your local Miele dealer.
The stainless steel hose supplied is
1.5m long.
Remove the cover cap from the fresh
water connection at the back of the
coffee machine.
Take the angled end of the stainless
steel hose and check whether there is
a sealing ring. Install one if necessary.
Screw the stainless steel hose
coupling nut onto the thread.
Ensure that it is screwed into position
correctly and watertight.

11823040-02
Installation
*INSTALLATION*
Connecting the water supply
Disconnect the coffee machine
from the power supply before
connecting it to the water supply.
Turn off the water supply at the
faucet before connecting the coffee
machine to the water supply.
Make sure that the faucet remains
accessible after the machine has
been installed.
To connect the coffee machine to the
water supply, a faucet with a 3/4"
connection is required.
Check that a sealing ring is present.
Install one if necessary.
Connect the stainless steel hose to
the faucet.
Ensure that it is screwed into position
correctly.
Turn on the water supply faucet
slowly and check for leaks at the
fresh water connection.
Correct the position of the seal and
screw thread if appropriate.
You can now continue installing the
coffee machine.

11823040-02
Installation
*INSTALLATION*
Electrical connection
Before connecting the coffee machine,
make sure that the connection data on
the data plate (voltage and frequency)
matches that of the domestic electrical
supply.
This data must match to prevent the
coffee machine from being damaged. If
in any doubt, consult a qualified
electrician.
The necessary connection data is given
on the data plate inside your appliance.
The fuse rating must be at least 10A.
If possible, the socket should remain
easily accessible. If the socket is no
longer accessible after installation, an
additional means of disconnection must
be provided for all poles. Suitable
means of disconnection include
switches with an all-pole contact gap of
at least 3mm. These include circuit
breakers, fuses, and contactors
(EN60335).
Do not connect the coffee machine to a
stand-alone inverter. Stand-alone
inverters are used for autonomous
power supply, e.g., a solar power
system. Power surges could trigger the
safety shut-off function. This can
damage the electronics.
The coffee machine must not be used
with energy-saving plugs. These
reduce the amount of energy supplied
to the appliance, causing it to overheat.

11823040-02
Installation
*INSTALLATION*
Installation dimensions
Installation in a tall cabinet
Observe the required minimum installation height of 33 7/16" (850mm).
Your coffee machine can be installed flush or proud. Discuss your requirements
with your architect, kitchen designer, and installer.
More installation drawings are available on the Miele website.
Combination with other Miele Built-in Appliances is possible. If the coffee machine
is to be built in above another appliance, there must be a full-width, closed shelf
between them. If the machine is to be combined with a suitable built-in
dishware/food-warming drawer, no shelf is required in between.

11823040-02
Installation
*INSTALLATION*
Installation and connections
ACut-out (at least 20"/508mm wide) in the base of the tall cabinet for power
cord and ventilation
EElectrical connection
WFresh water connection
No electrical or fresh water connection in this area

11823040-02
Installation
*INSTALLATION*
Building in the coffee machine
Danger of injury due to incorrect
operation.
A machine that has not been built in
is not safe and can cause injuries.
Do not operate the coffee machine
unless it has been built in.
Danger of damage due to
incorrect operation.
If the ambient temperature is not
within the permitted range, the
coffee machine cannot function
properly.
The coffee machine may only be
operated within an ambient
temperature range of +16°C to
+38°C.
Maintain the required minimum
installation height of
337/16" (850mm).
Risk of damage and injury from
the coffee machine tipping over.
If the coffee machine is not screwed
to the housing unit, the appliance
may tip forward when the appliance
door is open.
Make sure that a second person fully
secures the coffee machine during
installation.
First screw the top-left screw to the
housing unit.
Risk of damage due to the use of an
electric screwdriver.
If the coffee machine is secured with
an electric screwdriver, e.g., a
cordless screwdriver, the chuck may
damage the appliance door and/or
the interior.
Only use a manual screwdriver to
secure the coffee machine in the
housing unit.
To install the machine, you will need a
TX20 screwdriver.
Removing transport restraints
2 screw holes are fitted with red silicone
plugs to protect the appliance against
transport damage and secure the door
during transport.
Remove the plugs before screwing
the coffee machine to the cabinet
unit.
Pull firmly on the red silicone plugs to
remove them from the screw holes.
The plugs are not required for any
other purpose. Dispose of them with
your household waste.

11823040-02
Installation
*INSTALLATION*
Useful tip: We recommend providing a
place to sit the coffee machine which is
the same height as the building-in
niche. This will make it easier to
connect the machine to the electricity
and water supply.
Connecting the fresh water and
electricity supplies
Observe the information under
“Fresh water connection” and
“Electrical connection”.
Connect the coffee machine to the
fresh water and electricity supplies.
Pushing in and aligning the coffee
machine
When pushing the machine into the
niche, make sure that the electrical
and fresh water connections do not
get trapped or damaged.
Push the coffee machine all the way
into the niche until you feel a
resistance.
Check the height of the coffee
machine to make sure that it is sitting
centrally in the niche and that it is
level. Align the machine.
Never align the coffee machine by
adjusting the door hinges. This will
prevent the milk container from
attaching correctly and interfere with
the milk preparation process.
Screwing the coffee machine to the
housing unit
Open the appliance door.
FourTX20 (25mm) screwsare
supplied with the machine.
Secure the coffee machine to the side
walls of the housing unit using the
screws supplied. Start with the top-
left screw. Proceed in a clockwise
direction to tighten the other screws.
Tighten all screws by hand.
Carry out a functional check on the
coffee machine.