Miele PW 6088 EL LP User manual

14.14 M.-Nr. 09 923 540
Installation Plan
Washer-extractor
PW 6088 EL LP
en - AU

M.-Nr. 09 923 540
2
Australia:
Miele Australia Pty. Ltd.
1 Gilbert Park Drive
KNOXFIELD
Victoria 3180
Tel. [phone]
Fax [phone]
Internet: www.miele.com.au
It is essential to read the operating and installation instructions before
installing, commissioning or using the machine.
This avoids the risk of accidents or damage.
All rights reserved

A - A B - B

C - C

Technical datasheet: PW 6088 EL LP
Date: 01.04.2014 Page: 7
Technical datasheet
Washer-extractor:
Heating:
PW 6088 LP
Electric (EL)
Legend:
Abbreviations in bold type:
Connection required
en - AU
Abbreviations in circle with dashes:
Connection optional or required depending on model version
Optional extras:
UM
Miele plinth
US 6008 (US = plinth with drawer)
Height
mm
320
Width
mm
692
Depth
mm
685
BS
Concrete plinth
Quality and density of concrete must comply with load. Con-
crete plinth must be firmly secured to floor!
Recommended height
mm
300
Minimum height
mm
70
Recommended width
mm
≥700
Recommended depth
mm
≥700
Machine connections:
Electrical
connection
1. Standard voltage (as supplied)
V
1N AC 230
Frequency
Hz
50
Rated load
kW
5.5
Fuse rating
A
1 × 25
Supply lead cross-section
mm²
3 × 2.5
Length of supply lead
mm
2170
Supply lead without plug (supplied)
Electrical connection must comply with national regula-
tions.
A wall socket or mains isolator must be easily accessible
after installation.
Reinstallation of the supply point, changes to the equip-
ment or checks on the protective conductor, including de-
termination of correct fuse rating, should only be per-
formed by a properly trained electrician.

Technical datasheet: PW 6088 EL LP
Date: 01.04.2014 Page: 8
Cold water
(Soft water)
Min. flow pressure
kPa
100
Max. pressure
kPa
1000
Max. throughput
l/min
11
On-site connection thread according to DIN 44 991
Inch
¾" external thread
Length of connection hose
(supplied) 1 connection hose)
mm
1550
Water requirements (average for 60°C programme)
Standard connection (hot water fill)
l/h
approx. 70
Additional requirements if hot water supply is not available.
If connected to grey water supply (optional), subtract from
cold water volume.
Hot water
(Soft water)
Max. temperature
°C
70
Min. flow pressure
kPa
100
Max. pressure
kPa
1000
Max. throughput
l/min
11
On-site connection thread according to DIN 44 991
Inch
¾" external thread
Length of connection hose
(supplied) 1 connection hose)
mm
1550
Water requirements (average for 60°C programme)
l/h
approx. 70
Machine can be connected to a hot water supply line with a
temperature of 70°C to max. 85°C. This requires a separate
inlet hose. This additional inlet hose is available from Miele
Spares. The machine must also be reprogrammed by Miele
Service or an authorised agent.
If hot water is not available, connect hot water hose to cold
water valve!
Waste water
Model versions
with drain pump
Max. temperature °C 70
Drain hose (int. diameter) mm 22 [DN 22]
On-site hose connector for drain hose
(int. diameter x length)
mm 22 × 30
Max. transient throughput l/min 26
Drain pump head height (from floor level) mm 1000
Vented drainage required. If ventilation is insufficient, fit Miele
kit, Mat. No. 05238090.
Drain manifolds serving several machines must be of suffi-
cient cross-section.
Fittings (supplied)
Miele US 6008 plinth
4 × metal angled brackets
(to secure machine to plinth)
4 × screws DIN 571 (Ø × length) mm 6 × 50
4 × rawl plugs (Ø × length) mm 8 × 40
Machine must be bolted to the floor!
Fixing materials for a floating screed floor are to be provided
on site.
mm 6 × 50
mm 8 × 40
On concrete platform
2 × clamps
2 × screws DIN 571 (Ø × length)
2 × rawl plugs (Ø × length)
Machine must be bolted to the floor!
Fixing materials for a floating screed floor are to be provided
on site.
Machine data Unit width mm 700
Machine depth mm 727
Unit height mm 1020
Casing width mm 692
Casing depth mm 690
mm 720
mm 1100
Minimum width of delivery access to installation site
Minimum rear wall gap (measured to front of machine)
Wall gap (to front of machine)
Minimum gap ensures sufficient space for maintenance and
servicing.
mm 900
kg 140
N 2750
N 1960
N 790
Hz 22
Net weight
Dynamic floor load, max.
Static floor load, max.
Dynamic load, max.
Drum frequency, max.
Average heat dissipation
(dependent on ambient room temperature and
programme selected)
W not yet available
Sound pressure (re 20 mPA),
workplace-related (at distance of 1 m and height of 1.6 m)
dB (A) <70
Installation should only be carried out by authorised fitters in accordance with valid regulations!
Observe installation instructions when installing machine! All rights reserved! Measurements in mm.