Mighty Module MM4410 User manual

MM4410 &
MM4410ISO
DC INPUT
MULTIPLIER
TRANSMITTER
DESCRIPTION
The MM4410modules provide a DC output
voltage or current proportional to the
product of two DC inputs. Typical input
ranges are 4/20 mA, 10/50 mA, 0-1 V, 0-
5 V, and 0-10 VDC. Other ranges are
available down to minimum spans of 1 V
or 1 mA DC.
The two inputs are emplified and applied
to a complex integrated circuit which
performs the multiplication function. The
resulting product is applied to an output
stage which provides the final DC voltage
or current output. Zero and span
adjustments in the output circuit allow
precise calibration.
For current inputs, internal shunt resistors
creat DC voltage levels at the amplifier
inputs. Input offset capability permits
multiplication of offset inputs such as 4/
20 mA.
Standard calibration provides the output
at full scale (100%) when both inputs are
at full scale (100%). Other calibrations are
available.
OPTIONS
UAll circuit boards conformal coated for
protection against moisture
DC Power 12 V or 24 VDC power
CONTROLS
TheMM4410modulescontaintwocalibration
controls,ZEROandSPAN. Bothareavailable
at the top of the module.
CALIBRATION
The modules are shipped precalibrated and
does not normally need adjustment. If you
need to recalibrate, proceed as follows:
Monitor the output with an accurate meter
and insert input signals into both inputs. Set
Input A to its minimum level, Input B to full
scale. Adjust the ZERO control for the
proper output. Increase Input A to full scale
and adjust the SPAN control for the proper
output. Repeat the procedure, the controls
may interact slightly.
MOUNTING
The module is designed to plug into a stan-
dard8-pinrelaysocket. (MP008)isamolded
plastic socket suitable for mounting on a flat
surfaceorina 2¾inchwide PVC snap track
(TRK48). Use (CLP1) hold down clip, if
needed. A Killark HK Series explosion-proof
housingwith domeand 8-pinsocket isavail-
able (HKB-HK2D-8). A DIN rail socket
(DMP008)isavailablefor35mmsymmetrical
DINrail.
WARRANTY
The Mighty Module Series of products carry
a limited warranty of 10 + 5 years. In the
event of a failure due to defective material
or workmanship, during the 10 year period,
the unit will be repaired or replaced at no
charge. For a period of 5 years after the
initial 10 year warranty, the unit will be
repaired, if possible, for a cost of 10% of
the original purchase price.
Relays are not covered by the warranty.
1 2

DIMENSIONS INCHES [mm]
SPECIFICATIONS
INPUT RANGE
Voltage
select any range between
±250 V max (min span 1 V)
Typical inputs: 0-1 V, 0-5 V, 0-10V
Current
select any range between
±100 mA max (min span 1 mA)
Typical inputs: 4/20 mA or 10/50mA
INPUT IMPEDANCE
Voltage
100 kilohms min
Current
1.25 V drop typical, others available
OUTPUT RANGE
Voltage
select any range from
-10 V to +15 V,10 mA max load
(min span 0.2 V)
Current
select any range from 0 to 50 mA
max,
>24 V compliance
(1200 ohms at 20mA max)
18 V compliance for ISO option
if full scale output >20 mA
RESPONSE TIME
≤150 ms (range dependent)
ACCURACY
± 0.25% of span
ISOLATION (MM4410ISO)
Output/Input
>500 megohms
Breakdown Voltage
>1000 VAC rms
Output Ripple (peak-to-peak)
<0.1% of span
Breakdown, Pwr/Circuitry
>1500 VAC rms
OPERATING TEMPERATURE
14°F to 140°F/–10°C to 60°C
TEMPERATURE STABILITY
±0.02% of span/°C max
POWER
115 VAC ±10%, 50 or 60 Hz
(2.5 W max)
230 VAC ±10%, 50 or 60 Hz
(2.5 W max)
(DC Power Option)
24 VDC (limits 21 VDC to
32 VDC) (2.5 W max)
Isolation, DC power supply to
input common: 10 megohms
Specifications are subject to change withoout notice. © 2008 Wilkerson Instrument Co., Inc. DWG#103496 06/08
MM4410
MM4410ISO
34