Mighty Seven SJ-1650T User manual

1
1.The maximum recommended air pressure during operation must not exceed 90 psi
(6.3bar). Higher air pressure may create unsafe operating conditions for the tool and
the user.
2.The compressed air should be cooled and have a water lter installed at the outlet
end of the compressor. Even with a water filter installed, some water may still
condense in the piping or hose and will enter the tool mechanism causing premature
damage to the tool. Therefore, it is recommended to install an air filter-lubricator
device somewhere between the tool and the compressor.
3.Always use an air compressor of the proper capacity to operate each tool.
4.Clean the hose with a blast of compressed air before connecting the hose to the air
tool. This will prevent both moisture and dust inside the hose from entering the tool
and causing possible rust or malfunction.
1.Using these tools in any potentially explosive environment is strictly prohibited.
2.It is always recommended that these types of tools must be operated when standing
on a solid or rm location.
3.Always use these tools in a well ventilated area.
4.Slipping, stumbling and falling are the major causes of potential serious injury,
therefore, a clean and clutter free surface in the working area before operating the
tools is strongly recommended.
Read this manual carefully before installing, operating,
servicing or repairing.
Working environment:
Air supply and connection requirements:

2
Ideal system connection:
Piping diameters and length requirement:
The diameter ΦA required for the inlet pipe is recommended on the specication table.
The diameter ΦB required for the branch pipe (from to ) should be 2 times as large as ΦA.
ΦB = 2 x ΦA
The diameter ΦC required for the primary air supply (from to ) should be 3 times as large as
ΦA. ΦC = 3 x ΦA
The length for the inlet pipe should be less than 15 feet (4.5m).

3
1. This tool should only be used as a hand operated tool. It is powered by compressed air and is not
insulated against electric shock.
3. High sound levels may cause hearing damage. Always wear hearing protection when operating this tool.
4. User must wear proper clothing. Loose clothing, long hair, stings, straps, belts and jewelry should not be
worn when operating this tool.
5. Wearing eye/face protection can reduce the danger of high-speed materials being ejected by the tool.
6. Working with certain materials may create emission of dust and fumes, which may cause a potential
explosive environment and a hazard to the health. Wearing correct breathing protection and taking some
preventive measures are recommended.
7. Make certain to stand on a solid or rm location and keep body in well-balanced position while operating
this tool.
8. Using this tool will cause particles when chipping or demolishing. Make sure there is no bystander within
the vicinity of working area.
9. To avoid vibration injury, the user should use other effective damping devices, in stead of free hand, to
hold the chisel when necessary.
10.Make sure that the all the specications of the nailer to be used are compatible with this tool.
11.Make sure that the direction of the nailer generated from the chisel is properly directed so as not to create
a hazard.
12.Always turn off the air supply and disconnect the air hose before changing the chisel or making
adjustments on this tool.
13.Release the throttle trigger to avoid danger if there is a failure of energy supply and when connecting or
disconnecting the air hose.
14.Beware if the compressed air hose breaks unexpectedly, or is being connected or disconnected
improperly. This whipping action may cause injury.
15.Prolonged use will cause user fatigue. Periodic breaks are recommended for user safety.
16.It is recommended to stop operating the tool whenever the user experiences discomfort, tingling or pain
during use.
17.Make sure there is no gas or combustible material stored near the tool when servicing, changing chisel,
or storage.
18.Avoid storing this tool where it is subject to high humidity.
Warning:

4
1. Before connecting the air hose to this tool or after operating, apply 4 or 5 drops of
pneumatic oil into the air inlet and run it for several seconds, referring this operation to the
attached picture.
2. Maintain this tool regularly by performing the same oiling application every 3 to 4 hours of
operation.
3. Do not lubricate tools with flammable or volatile liquids. Use only the lubricant
recommended by Mighty-Seven or authorized dealers. Any other lubricant will lead to
reduce performance of the tool and permanent damage. Whenever any unauthorized
lubricant is used by accident, ush it immediately with recommended pneumatic oil.
4. Follow all the recycling laws of waste disposal once this tool is no longer usable.
Maintenance:
Pneumatic oil
Air inlet
Regular maintenance

5
1. Before connecting the air hose to this tool or after operating, apply 4 or 5 drops of
pneumatic oil into the air inlet and run it for several seconds, referring this operation to the
attached picture.
2. Maintain this tool regularly by performing the same oiling application every 3 to 4 hours of
operation.
3. Do not lubricate tools with flammable or volatile liquids. Use only the lubricant
recommended by Mighty-Seven or authorized dealers. Any other lubricant will lead to
reduce performance of the tool and permanent damage. Whenever any unauthorized
lubricant is used by accident, ush it immediately with recommended pneumatic oil.
4. Follow all the recycling laws of waste disposal once this tool is no longer usable.
Nailer/stapler specications
Nail/Staple Loading Area
Trigger
Discharge Area
Work Contact
Element (WCE)
Rotatable
Exhaust Cap
Air and
Oil Inlet
Quick
Release
Latch
Magazine

6
Symptom: Air leak near top of nailer/stapler or trigger area.
Problem
Loose screws.
Worn or damaged o-rings or seals
Solutions
Tighten screws.
Contact factory for service. +(886) 4 23358567
Symptom: Nailer/stapler does nothing or operates sluggishly.
Problem
Inadequate air supply.
Inadequate lubrication.
tions.
Worn or damaged o-rings or seals.
Solutions
Check compressor settings Check air hose/lters for kinks or
blockage. Oil nailer/stapler per instruc.
Contact factory for service. +(886) 4 23358567
Symptom: Air leak near bottom of nailer/stapler.
Problem
Loose screws.
Worn or damaged o-rings or bumper.
Solutions
Tighten screws.
Contact factory for service. +(886) 4 23358567
Symptom: Nailer/stapler jams frequently.
Problem
Incorrect fasteners.
Damaged fasteners.
Magazine or nose screw loose.
Magazine is dirty.
Driver is worn or damaged.
Solutions
Verify fasteners are the correct size.
Replace with undamaged fasteners Tighten screws.
Clean magazine
Contact factory for service. +(886) 4 23358567
Symptom: Other
Problem
Other
Solutions
Contact factory for service. +(886) 4 23358567
Troubleshooting, continued:

7
Symptom: Air leak near top of nailer/stapler or trigger area.
Problem
Loose screws.
Worn or damaged o-rings or seals
Solutions
Tighten screws.
Contact factory for service. +(886) 4 23358567
Symptom: Nailer/stapler does nothing or operates sluggishly.
Problem
Inadequate air supply.
Inadequate lubrication.
tions.
Worn or damaged o-rings or seals.
Solutions
Check compressor settings Check air hose/lters for kinks or
blockage. Oil nailer/stapler per instruc.
Contact factory for service. +(886) 4 23358567
Symptom: Air leak near bottom of nailer/stapler.
Problem
Loose screws.
Worn or damaged o-rings or bumper.
Solutions
Tighten screws.
Contact factory for service. +(886) 4 23358567
Symptom: Nailer/stapler jams frequently.
Problem
Incorrect fasteners.
Damaged fasteners.
Magazine or nose screw loose.
Magazine is dirty.
Driver is worn or damaged.
Solutions
Verify fasteners are the correct size.
Replace with undamaged fasteners Tighten screws.
Clean magazine
Contact factory for service. +(886) 4 23358567
Symptom: Other
Problem
Other
Solutions
Contact factory for service. +(886) 4 23358567
进行安装、操作、维修或更换零件之前,请务必详读本使用手册
工作环境:
风源及安装需求
1.严格禁止在任何具有爆炸性气体的环境中使用本气动工具。
2.当使用本气动工具时务必站立在坚实稳固的物体或位置上。
3.使用本气动工具的场所, 其通风条件必须十分良好。
4.滑倒、绊倒和从高处跌落…等等状况乃操作气动工具时最容易发生的意外
状况, 因此在操作之前，务必先将工作场所清理干净。
1.操作本气动工具的最大空气压力值不得超过90psi。高于此压力值时将可能对本气动工具
或使用者带来危险险。
2.用于本气动工具的压缩空气必须经过冷却处理, 在空压机出口端务必加装ㄧ只过滤器,以
便过滤压缩空气中的水分。即便如此, 仍会有少部分的水气凝结于空压管路当中, 甚至渗
进本气动工具的机械结构内部, 造成本气动工具难以预期的损害。是故,压缩空气的管路在
进入本气动工具之前的某适当位上, 应予加装ㄧ只三点组合。
3.使用者应根据各种不同气动工具的需求, 选择不同规格的空气压缩机。
4.开始操作本气动工具之前, 应先将管路中的水气排除干净净。如此, 当可避免残留在压缩
空气中的水分或灰尘进入本气动工具内部,将影响到本气工具的正常性能, 甚至造成损坏。

8
1. 本气动工具完全采用压缩空气来加以驱动,仅限以手动方式进行操作。因本气动工具并不具效果,故
使用时特别注意不可接近电源。
2. 高分贝的噪音可能会使听力受损。故当使用本气动工具时请务必戴上防护耳罩。
3.使用者在使用本气动工具时，应绝对避免穿着宽松的衣服或配戴过长的腰带、珠宝、首饰…等等
物品；长头发亦必须包扎妥当。
4.为防范因异物或磨屑飞出而造成危险,操作本气动工具时务必穿戴眼部/ 脸部护具。
5.本气动工具运用在某些特定材质时会射出粉屑和烟尘尘, 此现象将会使工作还境潜藏爆炸性, 并对
人体健康造成危害。因此使用时务必配戴呼吸保护器具和适当的防护措施。
6. 操作时当站立在稳固坚实的物体或位置上,在身体平衡无虞的状况下才能操作本气动工具。
7. 使用本气动工具将造成物碎屑的喷溅,故作业前请务必确定工作范围内没有其它不相关的旁观者。
8. 为有效降低震动所造成的伤害,必要时采用有效的减震工具或防范措施来持握本气动工具。
9.作业之前请务必确钉子认规格与本气动工具相符。
10.使用前务必确认碎屑产生的方向不会产生任何的危险。
11.在更换钉子或调整本气动工具之前，请务必关闭风源，并将本气动工具与空压软管脱离。
12.当连接或脱离空压软管时,风源供应若产生问题,应立即释放扳机,以免造成危险。
13.不当拆卸、连接空压软管,或非预期性的软管断裂都将造成空压软管的任意甩动,此类危险操作之
时，宜特别注意。
14.长时间使用本气动工具将会造成使用者疲劳，为了使用者的安全着想,请请务必实施周期性地休
息。
15.在使用中有任何不适、颤抖、或疼痛的感觉时时，请务必立即停机休息。
16.更换,拆卸,维修,储放及操作本气动工具的场所周遭,绝对不得存放瓦斯或其它任何可燃性的气体。
17.应应尽可能避免将本气动工具储放在高湿度的还境当中。

9
1. 本气动工具完全采用压缩空气来加以驱动,仅限以手动方式进行操作。因本气动工具并不具效果,故
使用时特别注意不可接近电源。
2. 高分贝的噪音可能会使听力受损。故当使用本气动工具时请务必戴上防护耳罩。
3.使用者在使用本气动工具时，应绝对避免穿着宽松的衣服或配戴过长的腰带、珠宝、首饰…等等
物品；长头发亦必须包扎妥当。
4.为防范因异物或磨屑飞出而造成危险,操作本气动工具时务必穿戴眼部/ 脸部护具。
5.本气动工具运用在某些特定材质时会射出粉屑和烟尘尘, 此现象将会使工作还境潜藏爆炸性, 并对
人体健康造成危害。因此使用时务必配戴呼吸保护器具和适当的防护措施。
6. 操作时当站立在稳固坚实的物体或位置上,在身体平衡无虞的状况下才能操作本气动工具。
7. 使用本气动工具将造成物碎屑的喷溅,故作业前请务必确定工作范围内没有其它不相关的旁观者。
8. 为有效降低震动所造成的伤害,必要时采用有效的减震工具或防范措施来持握本气动工具。
9.作业之前请务必确钉子认规格与本气动工具相符。
10.使用前务必确认碎屑产生的方向不会产生任何的危险。
11.在更换钉子或调整本气动工具之前，请务必关闭风源，并将本气动工具与空压软管脱离。
12.当连接或脱离空压软管时,风源供应若产生问题,应立即释放扳机,以免造成危险。
13.不当拆卸、连接空压软管,或非预期性的软管断裂都将造成空压软管的任意甩动,此类危险操作之
时，宜特别注意。
14.长时间使用本气动工具将会造成使用者疲劳，为了使用者的安全着想,请请务必实施周期性地休
息。
15.在使用中有任何不适、颤抖、或疼痛的感觉时时，请务必立即停机休息。
16.更换,拆卸,维修,储放及操作本气动工具的场所周遭,绝对不得存放瓦斯或其它任何可燃性的气体。
17.应应尽可能避免将本气动工具储放在高湿度的还境当中。

10

SJ-C1830F
Shank
Dia
Head
Die Collated
Nail
Length
Driving
Power
(7kg/cm²)
Load
Capacity
Dimensions
(H*W*L ) Weight Working Pressure
2.1-2.3 5.0-5.7 Wire 36.54 300-350 283*131*270 2.8 90SJ-CN55
2.3-2.9 5.7-7.0
25-57
45-70 Wire 61.07 150-300 303*129*307 3.7 90SJ-CN70

10
20
30
40
50
60
70
71
72
61
61
62
63
64
65
66
67
68
69
51
52
53
54
55
56
57
58
59
41
42
43
44
45
46
47
48
49
31
32
33
34
35
36
37
38
39
21
22
23
24
25
26
27
28
29
11
12
13
14
15
16
17
18
19
1
2
3
45
6
7
8
9
64
51
55
12
Air Nailer
ltem No：SJ-1650T

13
ltem No：SJ-1650T
No. Index No. Q'ty
1 SJ-1650TNP01 1
2 SJ-1650TNP02 1
3 SJ-1650TNP03 1
4 SJ-1650TNP04 1
5 SJ-1650TNP05 1
6 SJ-1650TNT06 1 SET
7 SJ-1650TNP07 1
8 SJ-1650TNP08
1
9 SJ-1650TNP09 1
10 SJ-1650TNP10 1
11 SJ-1650TNP11 1
12 SJ-1650TNP12 1
13 SJ-1650TNP13 1
14 SJ-1650TNP14 1
15 SJ-1650TNP15 1
16 SJ-1650TNP16 1
17 SJ-1650TNP17 1
18 SJ-1650TNP18 1
19 SJ-1650TNP19 1
20 SJ-1650TNP20 1
21 SJ-1650TNP21 1
22 SJ-1650TNP22 1
23 SJ-1650TNT23 1 SET
24 SJ-1650TNP24 1
25 SJ-1650TNP25 SUPPORT 1
26 SJ-1650TNP26 UPPER SAFETY 1
27 SJ-1650TNP27 ROLLER
1
28 SJ-1650TNP28 COMPRESSION SPRING 1
29 SJ-1650TNP29 DRIVER SET 1
30 SJ-1650TNP30 MAGAZINE CAP 1
31 SJ-1650TNP31 BODY 1
32 SJ-1650TNP32 CYLINDER CAP 1
33 SJ-1650TNP33 CAP SEAL 1
34 SJ-1650TNP34 HEAD VALVE SEAT 1
35 SJ-1650TNP35 GASKET
1
36 SJ-1650TNP36 CYLINDER 1
PUSHER SPRING (2PCS)
BAR
TRIGGER VALVE SEAT
TRIGGER
CONTACT LEVER
GUIDE PLATE
PUSHER
COMPRESSION SPRING
MAGAZINE ASSY.
TRIGGER VALVE CAP
COMPRESSION SPRING
TRIGGER ASSY.
COVER PLATE(A)
PISTON STOP
HEAD VALVE CAP
SPRING
COVER PLATE(B)
MAGAZINE RETAINER
PUSHER PIN (2PCS)
STOP PLATE
Description
END CAP
LATCH
DRIVER ASSY.
PISTON STOP
No. Index No. Description Q'ty
37 SJ-1650TNP37 BUMPER 1
38 SJ-1650TNP38 MAIN PISTON 1
39 SJ-1650TNP39 COLLAR 1
40 SJ-1650TNP40 NOZZLE 1
41 SJ-1650TNP41 EXHAUST CAP 1
42 SJ-1650TNP42 TRIGGER VALVE ASSY. 1
43 SJ-1650TNP43 EXHAUST CAP RING 1
44 SJ-1650TNP44 TRIGGER VALVE STEM
1
45 SJ-1650TNP45 MAGAZINE SEAT 1
46 SJ-1650TNP46 FLAT HD.BOLT 1
47 SJ-1650TNT47 HEX.SOC.HD.BOLT
(2PCS)
1 SET
48 SJ-1650TNT48 HEX.SOC.HD.BOLT
(2PCS)
1 SET
49 SJ-1650TNT49 HEX.SOC.HD.BOLT
(2PCS)
1 SET
50 SJ-1650TNP50 HEX.SOC.HD.BOLT 1
51 SJ-1650TNT51 HEX.SOC.HD.BOLT
(4PCS)
1 SET
52 SJ-1650TNT52 HEX.SOC.HD.BOLT
(2PCS)
1 SET
53 SJ-1650TNT53 HEX.SOC.HD.BOLT
(4PCS)
1 SET
54 SJ-1650TNT54 HEX.SOC.HD.BOLT
(2PCS)
1 SET
55 SJ-1650TNT55 SPRING PIN (3PCS) 1 SET
56 SJ-1650TNP56 SPRING PIN 1
57 SJ-1650TNP57 O-RING 1
58 SJ-1650TNP58 O-RING 1
59 SJ-1650TNP59 O-RING 1
60 SJ-1650TNP60 O-RING 1
61 SJ-1650TNT61 O-RING (3PCS) 1 SET
62 SJ-1650TNT62 O-RING (2PCS) 1 SET
63 SJ-1650TNP63 O-RING
1
64 SJ-1650TNT64 O-RING (2PCS) 1 SET
65 SJ-1650TNP65 O-RING 1
66 SJ-1650TNP66 O-RING 1
67 SJ-1650TNP67 PIN 1
68 SJ-1650TNP68 E-RING 1
69 SJ-1650TNT69 SPRING WASHER
(2PCS)
1 SET
70 SJ-1650TNT70 SPRING WASHER
(2PCS)
1 SET
71 SJ-1650TNP71 LOCK NUT
1
72 SJ-1650TNT72 LOCK NUT (2PCS) 1 SET

10
20
30
40
50
60
61
62
63
64
51
52
53
54
55
56
57
58
59
41
42
43
44
45
46
47
48
49
31
32
33
34
35
36
37
38
39
21
22
23
24
25
26
27
28
29
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
64
32
14
Air Nailer
ltem No：SJ-1830F

15
ltem No： SJ-1830F
No. Index No. Description Q'ty
1 SJ-C1830FNP01 END CAP 1
2 SJ-C1830FNP02 DRIVER ASSY. 1
3 SJ-C1830FNP03 LATCH 1
4 SJ-C1830FNP04 SUPPORT 1
5 SJ-C1830FNP05 SPRING 1
6 SJ-C1830FNP06 EXHAUST CAP 1
7 SJ-C1830FNP07 DRIVER SET 1
8 SJ-C1830FNP08 PUSHER PIN 1
9 SJ-C1830FNP09 PUSHER SPRING 1
10 SJ-C1830FNP10 BODY 1
11 SJ-C1830FNP11 HEAD VALVE PISTON 1
12 SJ-C1830FNP12 COMPRESSION SPRING 1
13 SJ-C1830FNP13 PISTON STOP 1
14 SJ-C1830FNP14 CAP SEAL 1
15 SJ-C1830FNP15 COLLAR 1
16 SJ-C1830FNP16 MAIN PISTON 1
17 SJ-C1830FNP17 PIN 1
18 SJ-C1830FNP18 PISTON STOP 1
19 SJ-C1830FNP19 PISTON STOP 1
20 SJ-C1830FNP20 EXHAUST CAP RING 1
21 SJ-C1830FNP21 MAGAZINE CAP 1
22 SJ-C1830FNP22 MAGAZINE SEAT 1
23 SJ-C1830FNP23 PUSHER 1
24 SJ-C1830FNP24 MAGAZINE RETAINER 1
25 SJ-C1830FNP25 STOP PLATE 1
26 SJ-C1830FNP26 BAR 1
27 SJ-C1830FNP27 GUIDE PLATE 1
28 SJ-C1830FNP28 COVER PLATE 1
29 SJ-C1830FNP29 NOZZLE 1
30 SJ-C1830FNP30 CYLINDER CAP 1
31 SJ-C1830FNP31 FLAT HD.BOLT 1
32 SJ-C1830FNT32 HEX.SOC.HD.BOLT (3PCS) 1 SET
No. Index No. Description Q'ty
33 SJ-C1830FNT33 HEX.SOC.HD.BOLT (2PCS) 1 SET
34 SJ-C1830FNT34 HEX.SOC.HD.BOLT (2PCS) 1 SET
35 SJ-C1830FNP35 HEX.SOC.HD.BOLT 1
36 SJ-C1830FNP36 HEX.SOC.HD.BOLT 1
37 SJ-C1830FNT37 HEX.SOC.HD.BOLT (2PCS) 1 SET
38 SJ-C1830FNT38 HEX.SOC.HD.BOLT (4PCS) 1 SET
39 SJ-C1830FNT39 SPRING PIN (2PCS) 1 SET
40 SJ-C1830FNP40 O-RING 1
41 SJ-C1830FNP41 O-RING 1
42 SJ-C1830FNP42 O-RING 1
43 SJ-C1830FNP43 O-RING 1
44 SJ-C1830FNP44 O-RING 1
45 SJ-C1830FNP45 O-RING 1
46 SJ-C1830FNP46 O-RING 1
47 SJ-C1830FNP47 O-RING 1
48 SJ-C1830FNP48 O-RING 1
49 SJ-C1830FNP49 O-RING 1
50 SJ-C1830FNP50 PIN 1
51 SJ-C1830FNP51 SPACER 1
52 SJ-C1830FNP52 CYLINDER 1
53 SJ-C1830FNP53 BUMPER 1
54 SJ-C1830FNP54 TRIGGER VALVE ASSY. 1
55 SJ-C1830FNP55 COMPRESSION SPRING 1
56 SJ-C1830FNP56 TRIGGER VALVE STEM 1
57 SJ-C1830FNP57 SEAL 1
58 SJ-C1830FNP58 TRIGGER VALVE GUIDE 1
59 SJ-C1830FNP59 TRIGGER VALVE SEAT 1
60 SJ-C1830FNP60 TRIGGER 1
61 SJ-C1830FNP61 TRIGGER STOP 1
62 SJ-C1830FNP62 E-RING 1
63 SJ-C1830FNT63 SPRING WASHER (4PCS) 1 SET
64 SJ-C1830FNT64 LOCK NUT (2PCS) 1 SET

▲
▲
▲
▲
10
20
30
40
50
51
52
53
54
55
56
56
57
58
41
42 43
44
45
46
47
48
49
31
32
33
34
35
36
37
38
39
21
22
23
24
25
26
27
28
29
11
12
13
14
15
16
17
17
18
19
1
2
3
4
5
6
7
8
9
16
Air Stapler
ltem No：SU-C422J

17
ltem No：SU-C422J
No. Index No. Description Q'ty
1 SU-C422JNP01 END CAP 1
2 SU-C422JNP02 EXHAUST CAP 1
3 SU-C422JNP03 BODY 1
4 SU-C422JNP04 HEAD VALVE PISTON 1
5 SU-C422JNP05 COMPRESSION SPRING 1
6 SU-C422JNP06 PISTON STOP 1
7 SU-C422JNP07 CAP SEAL 1
8 SU-C422JNP08 COLLAR 1
9 SU-C422JNP09 MAIN PISTON 1
10 SU-C422JNP10 PIN 1
11 SU-C422JNP11 PISTON STOP 1
12 SU-C422JNP12 PISTON STOP 1
13 SU-C422JNP13 EXHAUST CAP RING 1
14 SU-C422JNP14 CYLINDER CAP 1
15 SU-C422JNP15 FLAT HD.BOLT 1
16 SU-C422JNT16 HEX.SOC.HD.BOLT (2PCS) 1 SET
17 SU-C422JNT17 HEX.SOC.HD.BOLT (6PCS) 1 SET
18 SU-C422JNP18 HEX.SOC.HD.BOLT 1
19 SU-C422JNP19 O-RING 1
20 SU-C422JNP20 O-RING 1
21 SU-C422JNP21 O-RING 1
22 SU-C422JNP22 O-RING 1
23 SU-C422JNP23 O-RING 1
24 SU-C422JNP24 O-RING 1
25 SU-C422JNP25 O-RING 1
26 SU-C422JNP26 O-RING 1
27 SU-C422JNP27 O-RING 1
28 SU-C422JNP28 O-RING 1
29 SU-C422JNP29 PIN 1
N
o. Index No. Description Q'ty
30 SU-C422JNP30 CYLINDER 1
31 SU-C422JNP31 BUMPER 1
32 SU-C422JNP32 DRIVER ASSY. 1
33 SU-C422JNP33 COVER PLATE 1
34 SU-C422JNP34 DRIVER SET 1
35 SU-C422JNP35 MAGAZINE ASSY. 1
36 SU-C422JNP36 MAGAZINE CAP SET 1
37 SU-C422JNP37 ADJUSTABLE PLATE 1
38 SU-C422JNP38 LATCH 1
39 SU-C422JNP39 LATCH SPRING 1
40 SU-C422JNT40 RETAINER SCREW (2PCS) 1 SET
41 SU-C422JNT41 GUIDE STEM (2PCS) 1 SET
42 SU-C422JNP42 PUSHER 1
43 SU-C422JNT43 PUSHER SPRING (2PCS) 1 SET
44 SU-C422JNT44 HEX.SOC.SET SCREW (2PCS) 1 SET
45 SU-C422JNP45 NOZZLE 1
46 SU-C422JNP46 MAGAZINE SEAT SET 1
47 SU-C422JNP47 TRIGGER VALVE ASSY. 1
48 SU-C422JNP48 COMPRESSION SPRING 1
49 SU-C422JNP49 TRIGGER VALVE STEM 1
50 SU-C422JNP50 SEAL 1
51 SU-C422JNP51 TRIGGER VALVE GUIDE 1
52 SU-C422JNP52 TRIGGER VALVE SEAT 1
53 SU-C422JNP53 TRIGGER 1
54 SU-C422JNP54 SPACER 1
55 SU-C422JNP55 E-RING 1
56 SU-C422JNT56 SPRING WASHER (6PCS) 1 SET
57 SU-C422JNP57 LOCK NUT 1
58 SU-C422JNT58 FLAT WASHER (2PCS) 1 SET

20
30
40
50
51
52 53
54
55
56
41
42
43
44
45
46
47
48
49
31
32
33
34
35
36
37
38
39
21
22
23
24
25
26
27
28
29
11
12
13
14
15
16
17
18
19
1
23
4
5
6
7
8
9
54
19
10
18
Air Stapler
ltem No：SU-C1022J

19
ltem No：SU-C1022J
NO. INDEX NO. DESCRIPTION Q'TY
01 SU-C1022JNT01 Screw (6PCS) 1set
02 SU-C1022JNP02 Exhaust Cover 1
03 SU-C1022JNP03 Compression Spring 1
04 SU-C1022JNP04 Seal, Air 1
05 SU-C1022JNP05 Cylinder Cap Ass'y 1
06 SU-C1022JNP06 O-Ring 1
07 SU-C1022JNP07 O-Ring 1
08 SU-C1022JNP08 Washer 1
09 SU-C1022JNP09 Head Valve Piston 1
10 SU-C1022JNP10 Piston Stopper 1
11 SU-C1022JNT11 O-Ring (2PCS) 1set
12 SU-C1022JNP12 O-Ring 1
13 SU-C1022JNP13 Collar 1
14 SU-C1022JNP14 Cylinder 1
15 SU-C1022JNP15 Bumper 1
16 SU-C1022JNP16 O-Ring 1
17 SU-C1022JNP17 Pipe 1
18 SU-C1022JNP18 O-Ring 1
19 SU-C1022JNP19 Body 1
20 SU-C1022JNP20 Nozzle 1
21 SU-C1022JNP21 Seal 1
22 SU-C1022JNP22 Trigger Valve Head 1
23 SU-C1022JNP23 Trigger Valve Stem 1
24 SU-C1022JNP24 O-Ring 1
25 SU-C1022JNP25 Trigger Valve Guide 1
26 SU-C1022JNP26 O-Ring 1
27 SU-C1022JNP27 Compression Spring 1
28 SU-C1022JNP28 E-Ring 1
NO. INDEX NO. DESCRIPTION Q'TY
29 SU-C1022JNP29 Trigger 1
30 SU-C1022JNP30 Step Pin 1
32 SU-C1022JNP32 O-Ring 1
33 - Piston Head 1
34 - Pin 1
35 - Spring Pin 1
36 - Spring Pin 1
37 - Driver Blade 1
38 SU-C1022JNP38 Spacer 1
39 SU-C1022JNP39 Driver Guide 1
40 SU-C1022JNP40 Click Lever 1
41 SU-C1022JNP41 Torsion Spring 1
42 SU-C1022JNP42 Hex. Nut 1
43 SU-C1022JNP43 Screw 1
44 SU-C1022JNP44 Step Pin 1
45 SU-C1022JNT45 Screw (2PCS) 1set
46 SU-C1022JNP46 Upper MAG. Ass'y 1
47 SU-C1022JNP47 Pusher 1
48 SU-C1022JNP48 Extension Spring 1
49 SU-C1022JNP49 Nail Tank Ass'y 1
50 SU-C1022JNT50 Cylinder Cap Set
(05,06) 1set
51 SU-C1022JNT51 Head Valve Piston Set
(09,10,11,12) 1set
52 SU-C1022JNT52 Cylinder Set (11,14) 1set
53 SU-C1022JNT53 Pipe Ass'y (17.18) 1set
54 SU-C1022JNT54 Trigger Valve Set
(22,23,24,25,26) 1set
55 SU-C1022JNT55 Piston Set
(32,33,34,335,36,37) 1set
56 SU-C1022JNT56 Magazine Set
(28,40-49) 1set

10
20
30
40
50
60
70
71
72 73
74
75
76
77
61
62
63
64
65
66
67
68
69
51
52
53
54
55
56
57
58
41
42
43
44
45
46
47 48
49
31
32
33
34
35
36
37
38
39
21
22
23
24
25
26
27
28
29
11 12
13
14
15
16
17
18
19
1
2
34
5
6
7
8
9
73
75
59
41
20
Air Nailer
ltem No：SJ-1850F