miGuard G3 User manual

Quick Start Guide
Wireless Burglar Alarm
Remote Monitoring/Communicating
GSM/SMS
lines open 0900 to 1700 Monday to Friday
“ whatever your question, we’re just a phone call away “
0345 257 1000
miGuard Customer Helpline
G3

1 x Control Unit
1 x PIR Motion Sensor
1 x Door/Window Sensor
2 x Remote Controls
KIT CONTENTS:
a. Read the instructions thoroughly
b. Remove all the contents from their packaging
c. Consider the most appropriate positioning
of the Control Panel and each Accessory
The Accessories supplied in the G5 box are
already pre-programmed to the Control Panel
for ease of installation (the Door/Window
sensor to Zone 1 and the PIR to Zone 2).
Any additional Accessories will need to be
programmed to the Control Panel, as shown in
the G5 Full Instruction Manual.
Before Installation:
1 x AC/DC Adapter
All Batteries and Fixings
Instruction Manual
G3
I. Installing the Control Unit
1. Plug the Power Jack into the Unit and Power
Supply/Plug into a suitable 13 amp socket.
2. Insert a standard size SIM Card (with credit) into
the SIM Card Slot (ensure that the Card is fully
pushed into the slot until it engages in place).
3. Depress/push-in the red Power ‘on/off’ Button 3
(ensure it stays depressed).
4. The Power and GSM Indicators will illuminate. The
GSM indicator (LED) will flash once every second
for a short period and will then flash once every
four seconds indicating that the GSM signal has
been found. You can now register your mobile
phone to the Control Unit.
5. If the LED flashes every second (GSM signal not
found) power down the Control Panel, remove the
SIM Card and wait 30 seconds. Insert the SIM
Card again and allow 1 minute for the signal to be
found, indicated by a flash once every 2 seconds.
Follow steps II to IV overleaf to install/set-up
the pre-programmed Accessories.
1
4
2
3
SIM Card Slot
Connect Button
Power ‘on/off’ Button
Power Adapter Socket
SIM
CARD
Ensure the SIM Card is
inserted into the slot this way
Side View
Congratulations on your purchase of the
G3 Remote Monitoring/Communicating
Burglar Alarm System
(Search by keyword: miGuard G3 Alarm)
a. Have available a mobile phone together with
either a PAYG or Contract regular size SIM
Card, on the network of your choice.
(SIM Card must work with 2G networks such as:
Vodafone, O2, Orange, T-Mobile)
b. Know the SIM Card telephone number
c. Ensure the SIM Card has available credit
d. Turn off/disable the SIM Card’s voicemail
function and PIN request
A SIM Card is required to program the Control Unit from
your mobile phone (This may take up to 25 text inputs and
a further 25 text replies).
Once programmed, the SIM Card can be removed from the
Control Unit if the remote phone functions are not required.
Please consider that most mobile tariffs include free texts or
a generous monthly allowance (you will not need any data
allowance).
Control Unit SIM Card
IMPORTANT NOTES TO BE READ
PRIOR TO SETTING UP YOUR SYSTEM

1. Remove the activation strip.
2. Remove one side of the double-sided tape
and fix the tapes to the back of the Magnet
and Transmitter.
3. Remove the paper strips and mount the
Magnet on the door and the transmitter on
the door jamb (small triangles adjacent to
each other) with less than a 6mm separation
between the two. When opening the door a
small red indicator lights up briefly, this
indicates that the Transmitter has sent a
signal to the Control Panel.
1. Remove the activation strip. Fit the retaining
screw supplied.
2. Self-testing will commence for 1 minute,
indicated by the LED flashing every two
seconds. Press the Test Button, the LED will
then flash once when movement is detected,
for up to 3 minutes.
3. Fit the Sensor in a position that will cover
your desired protection area.
a. Fix the bracket to the wall with the fixings kit
supplied. For optimum performance set the
the height of the bracket to 2 metres above
ground level.
b. Adjust angle of the PIR sensor to cover the
required detection area (see diagrams **).
4. To test, walk in front of the Sensor - the LED
should illuminate once when movement is
detected. If the Sensor is triggered twice in 3
minutes, it will enter into power saving (sleep
mode). If no movement is detected within
the next 3minutes, the Sensor will return to
normal working mode.
II. Installing a Door/Window Sensor
Please refer to the System’s full instruction
manual for detailed programming
III. Installing a PIR Motion Sensor
1. Press the Arm Button on the Remote Control
2. The Control Panel will emit one beep to
indicate that it is armed.
3. If your Control Panel is set to delay it will
beep every two seconds for half of the
duration of the delay, it will intensify in
tempo for the remaining duration to warn
that System Arming is imminent.
IV. Remote Control Operation
2
Top Side
Ground
2m 4m 6m0m
0m
2m
110°
Top view Side
Detection Range /
** diagrams (ref. 3a & 3b)

G3_Q_V2_1424
miGuard is a trademark of Response Electronics Limited © copyright 2013. All rights reserved
www.responseelectronics.com
Response Electronics Limited
Roman House, Lysons Avenue, Ash Vale, Surrey, GU12 5QF
email: [email protected]
The product is guaranteed for one year from the date of purchase against faulty materials and
workmanship. No liability can be accepted for any problems caused by fair wear and tear,
buyer’s negligence, improper fitting or use, wilful or accidental damage, or any consequential
loss or damage howsoever caused. This guarantee does not affect your statutory rights and is
valid for UK and EIRE only.
If you believe the product to be faulty or in the unlikely event of the product developing a fault
during the warranty period, then please contact our Technical Support Team (contact details
shown below) for product assistance. Product repair or replacement will be offered for faulty
products only with our prior agreement. Should you need to return a product then:
1. Contact the Helpline on the number below to obtain a Return Authorisation Number
2. Return your product adequately packaged, ideally in its original packaging to prevent damage
in transit, and include the following:
a. A copy of your original invoice/receipt
b. A covering letter giving your full contact details, including email address (if applicable)
c. A description of the fault or problem
GUARANTEE
Disposal and Recycling
Disposal of this product is covered by the Waste Electrical or Electronic Equipment (WEEE)
Directive. It should not be disposed of with other household or commercial waste.
At the end of its useful life the packaging and product should be disposed of via a suitable
recycling centre. Please contact your local authority or the retailer from where the
product was purchased for information on available facilities.
0345 257 1000
miGuard Customer Helpline