Honeywell LYNXR-2 Series Security System Operating instructions

LYNXR-2
Security Systems
Programming Guide
ARMED READY
BYPASS
NO DELAY
RECORD
TEST
FUNCTION
STATUS
VOLUME PLAY
CODE
LIGHTS ON
LIGHTS OFF CHIME
ESCAPE
ADD
DELETE
SELECT
OFF
123
6
AWAY
45
AUX
STAY
0
789
K15013 7/08 Rev. A

- 2 -
TABLE OF CONTENTS
Data Fields................................................................................................................................................................3
✻56 Enhanced Zone Programming........................................................................................................................11
✻80 Device Programming.......................................................................................................................................13
✻81 Zone Lists........................................................................................................................................................14
✻83 Enhanced Sequential Mode ...........................................................................................................................15
✻84 Assign Zone Voice Descriptors.......................................................................................................................16
Vocabulary Index (for ✻84 Assign Zone Voice Descriptors) ..................................................................................16
✻85 Record Custom Voice Descriptors..................................................................................................................18
✻56 Enhanced Zone Programming Worksheet......................................................................................................18
Powerline Carrier Device Worksheet for ✻80 and ✻81...........................................................................................20
5800 Series Transmitter Loop Numbers Diagram ..................................................................................................21
Special Messages...................................................................................................................................................22
LYNXR-2 Summary of Connections Diagram.........................................................................................................23
Refer to the Installation and Setup Guide for detailed information on programming the LYNXR-2 system. The
Installation and Setup Guide includes full descriptions of all data fields.
ULLYNXR-2 is not intended for UL985 Household Fire applications unless a 24-hour backup battery
(P/N LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.
TO ENTER PROGRAMMING MODE:
1. Power up, then depress [✻
✻✻
✻] and [#] both at once, within 50 seconds of powering up.
OR
2. For factory defaulted system, enter: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0. OR
If different Installer Code is programmed, enter: New Installer Code + 8 + 0 + 0.
(if ✻98 was used to exit previously, method 1 above must be used to enter the program mode again)
3. Upon entry into Program mode, data field ✻20 will be displayed (the first data field in the system) and both
keypad LEDs will flash.
TO PROGRAM THE DATA FIELDS:
1. Press [✻] followed by the desired field number (e.g., ✻21), then make the required entry.
2. The keypad beeps three times after entering data, then displays the next data field in sequence.
3. For phone number and account number fields, press [✻] to end the entry if less than number maximum
number of digits is entered.
4. To delete an entry, simply press [✻] plus that field number and reenter the correct data. For phone number
and account number fields ✻40-✻44, ✻88 and ✻94, press [✻] + field number + [✻].
INTERACTIVE MENU MODES:
There are six interactive menu modes as listed below. To enter these modes, first enter Program mode. While in
Program mode, press [✻] plus the mode number desired (e.g., ✻56).
✻56 Enhanced Zone Programming...............For programming zone characteristics, report codes, etc.
✻80 Device Programming..............................For programming Powerline Carrier Devices
✻81 Zone List Programming..........................For programming zone lists for use with Powerline Carrier Devices
✻83 Enhanced Sequential Mode ...................For entering transmitter serial numbers
✻84 Assign Zone Voice Descriptors ..............For assigning voice descriptors to zones
✻85 Record Custom Voice Descriptors .........For recording custom voice descriptors

- 3 -
TO LOAD A DEFAULT SET:
While in Program mode, press ✻97, then enter a number 1-4 corresponding to the default table desired. See
the Installation Instructions for the default tables. Enter 0 if you are not selecting a default table.
TO EXIT PROGRAMMING MODE:
✻98 Exits programming mode and prevents re-entry by: Installer Code + 8+ 0 + 0. If ✻98 is used to exit programming
mode, system must be powered down, then press [✻] and [#] within 50 seconds of power up to re-enter
programming mode.
✻99 Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or: Power-up, then press [✻] and [#]
within 50 seconds of power up.
DATA FIELDS
Field Function Programmed Values [ ] = Table 1 Default Values
SYSTEM SETUP (✱20– ✱ 30)
✱20 INSTALLER CODE [4112]
Enter 4 digits, 0–9
✱21 QUICK ARM ENABLE †[1]
0 = no; 1 = yes
✱22 KEYPAD BACKLIGHT TIMEOUT [0]
0 = none (backlighting always on); 1 = backlight off after 10secs
✱23 FORCED BYPASS †[0]
0 = none; 1 = bypass open zones
UL installations = 0
✱24 RF HOUSE ID CODE | [00]
00 = disable all wireless keypad usage;
01–31 = 5804BD/5804BDV house ID
✱25 POWERLINE CARRIER DEVICE
HOUSE CODE [0]
0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G, 7 = H, 8 = I,
9 = J, #10 = K, #11 = L, #12 = M, #13 = N, #14 = O, #15 = P
✱26 CHIME BY ZONE †[0]
0 = no; 1 = yes (program zones to chime on zone list 3)
✱27 REAL TIME CLOCK DISPLAY †[1]
0 = no; 1 = yes, display time on keypad
✱29 DAYLIGHT SAVING TIME
START/END MONTH [3, 11]
Start End
1-9, #+10,#+11,#+12. Enter 0,0 if no daylight savings time used.
✱30 DAYLIGHT SAVING TIME
START/END WEEKEND [2,1]
Start End
0=disable; 1=first; 2=second; 3=third; 4=fourth;
5=last; 6=next to last; 7=third from last
ZONE SOUNDS AND TIMING (✱
✱✱
✱31– ✱
✱ ✱
✱ 39)
✱31 SINGLE ALARM SOUNDING/ZONE † [0]
0 = Alarm Sounding Per Zone will be the same as the Swinger
Shutdown” set in field *92;
1 = yes, limit once per arming period (also applies to long range
radio output if “0” is selected in ✻91 field)
UL installations = 0
† Entering a number other than the one specified may give unpredictable results.

- 4 -
Field Function Programmed Values [ ] = Table 1 Default Values
✱32 SOUNDER TIMEOUT †[0]
0=timeout; 1=no timeout
✱33 ALARM BELL TIMEOUT †[1]
0 = none; 1=4 min; 2=8 min; 3=12 min; 4 = 16 min
UL installations = 1 (4 min) minimum
✱34 EXIT DELAY | †[70]
00-99 = exit delay time (in seconds).
UL installations = 60 seconds max.
✱35 ENTRY DELAY 1 (zone type 01) | †[30]
00-99 = entry delay time (in seconds);
UL installations = 45 seconds max.
✱36 ENTRY DELAY 2 (zone type 02) | †[60]
00-99 = entry delay 2 time (in seconds);
UL installations = 45 seconds max.
✱37 AUDIBLE EXIT WARNING /
QUICK EXIT † [1, 1]
Exit Warn Quick Exit
0 = no; 1 = yes
✱38 CONFIRMATION OF ARMING DING
Note: If LYNX is armed by RF button (key fob),
a confirmation ding occurs immediately after
arming regardless of field *38 settings. If LYNX
is disarmed by RF button (key fob), additional
disarming confirmation ding is provided. The
ding occurs immediately after disarming and is
longer than arming confirmation ding.
† [0]
0 = no arming confirmation ding after arming system by APX32EN keypad or
RF keypad; 1 = arming confirmation ding after arming system by APX32EN
keypad or RF keypad; 2 = arming confirmation ding after arming from RF
keypad only
If Option 1 is selected, confirmation of arming is provided by a 1/2 second
sounder “ding” that sounds when closing report is sent, or at the end of exit
delay. If Option 2 is selected the external sounder “ding” occurs immediately
after arming from an RF keypad.
Note: Confirmation ding only sounds when LYNX is Armed Away or disarmed
after being Armed Away.
✱39 POWER UP IN PREVIOUS STATE † [1]
0 = no; 1 = yes; UL installations = 1
† Entering a number other than the one specified may give unpredictable results.
DIALER PROGRAMMING (✱40– ✱ 53)
In fields ✱40, ✱41, ✱42, enter up to the number of digits shown. Enter 0–9; #+11 for '✻'; #+12 for '#'; #+13 for
a pause.
✱40 PABX ACCESS CODE
Enter 6 digits. If fewer than 6 digits are entered, pressing ✻
advances to the next field. To clear entries from field, press ✻40✻
✱41 PRIMARY PHONE NUMBER
Enter up to 20 digits; Do not fill unused spaces. If fewer than 20 digits
entered, pressing ✻advances to the next field. To clear entries from
field, press ✻41✻.

- 5 -
Field Function Programmed Values [ ] = Table 1 Default Value
✱42 SECONDARY PHONE NUMBER
Enter up to 24 digits; Do not fill unused spaces. If fewer than 24 digits
entered, pressing ✻advances to the next field. To clear entries from
field, press ✻41✻.
!
All four digits of the subscriber account number must be entered in Fields ✻
✻✻
✻43 and ✻
✻✻
✻44. If ten digit format is
selected in ✻
✻✻
✻48 (option 5), all ten digits of the Subscriber Account number must be entered.
For fields ✻43, ✻44:
Enter 4 to 10 digits. Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; [#+15 for F]. Enter ✻ as 4th digit, if 3+1
dialer reporting is to be used. If only 3 digits used, pressing ✻advances to the next field. Enter [✻] as the fifth digit if a 4-
digit account number (for 4+1, 4+2, CID®) is used.
To clear entries from field, press ✻43✻ or ✻44✻. Examples:
For Acct. 1234, enter: 1 | 2 | 3 | 4 ; For Acct. B234, enter: #+11| 2 | 3 | 4 For Acct. 1234567890, enter:
1| 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 ; For Acct. 123, enter: 1 | 2 | 3 | ✻
✱43 PRIMARY SUBS ACCT # See note above.
✱44 SECONDARY SUBS ACCT # See note above.
For field ✻46
Enter up to 24 digits. Enter 0-9, #+11 for ‘✻’; #+12 for ‘#’; #+13 for a pause (two seconds).
✱46 “FOLLOW ME” REMINDER
PHONE NUMBER
Enter up to 24 digits; Do not fill unused spaces. If fewer than 24 digits
entered, pressing ✻advances to the next field. To clear entries from
field, press ✻46✻.
✱47 PHONE SYSTEM SELECT †[5]
Central Dialing Mode
Station Pulse Tone Pulse Tone
No WATS 0 = No Speaker
Phone
1 = No
Speaker Phone
4 = With
Speaker Phone
5 = With
Speaker Phone
WATS 2 = No Speaker
Phone
3 = No
Speaker Phone
6 = With
Speaker Phone
7 = With
Speaker Phone
✱48 REPORT FORMAT for PRIM./SEC [7, 7]
Primary Secondary
0 = 3+1, 4+1 ADEMCO L/S STANDARD
1 = 3+1, 4+1 RADIONICS STANDARD
2 = 4+2 ADEMCO L/S STANDARD
3 = 4+2 RADIONICS STANDARD
5 = ADEMCO CONTACT ID® REPORTING WITH 10-DIGIT SUBS ACCT NO.
6 or undefined = 4+2 ADEMCO EXPRESS
7 = ADEMCO CONTACT ID® REPORTING WITH 4-DIGIT SUBS ACCT NO.
8 = 3+1, 4+1 ADEMCO L/S EXPANDED
9 = 3+1, 4+1 RADIONICS EXPANDED
† Entering a number other than the one specified may give unpredictable results.
Note: If you are using Pulse (rotary) Dialing, you must
enter the numbers slowly to allow the pulse dialer
time to o
p
erate.
Note: Option 5 or 7 (ADEMCO Contact ID®)
must be selected for AAV.

- 6 -
Field Function Programmed Values [ ] = Table 1 Default Value
✱49 SPLIT/DUAL REPORTING [0]
0 = Disable (None, unless primary fails)
TO PRIMARY PHONE No. TO SECONDARY PHONE No.
1 = Alarms, Restore, Cancel Others
2 = All except Open/Close, Test Open/Close, Test
3 = Alarms, Restore, Cancel All
4 = All except Open/Close, Test All
5 = A l l All
** Pager Message
A 7-digit code (plus optional 16-digit prefix) is
sent to the pager consisting of a 3-digit event code,
followed by 0 and a 3-digit user or zone number.
See Installation Instructions for an explanation of
the pager code, which takes the following form:
AAAAAAAAAAAAAAAA-EEE-0NNN
TO PRIMARY PHONE No.
6 = All except Open/Close
7 = All reports
8 = All reports
9 = All except Open/Close
TO PAGING** No. (Secondary)
Alarms, Open/Close‡, Troubles
Alarms, Troubles
Alarms, Open/Close‡, Troubles
Open/Close‡
‡Will report users 0, 5-8 or wireless
arm/disarm button zones 26-33; all other
zones and users do not report
AAA… = optional 16-digits (see field ✻88)
EEE = 3-digit event code: 911 (alarm), 101 (open), 102 (close),
811 (trouble)
0 = always displayed
NNN = 3-digit user number or zone number, depending on the
type of event (EEE) that occurred.
TO PRIMARY PHONE No.
10 = All except Open/Close
11 = All reports
12 = All reports
13 = All except Open/Close
TO SECONDARY (“FOLLOW
ME”) SYSTEM PHONE No.
Alarms, Open/Close‡, Troubles
Alarms, Troubles
Alarms, Open/Close‡, Troubles
Open/Close‡
‡Will report users 0, 5-8 or wireless
arm/disarm button zones 26-33; all other
zones and users do not report
✱50 15 SEC DIALER DELAY (BURG) †[0]
0 = no; 1 = yes; UL installations = 0
✱51 PERIODIC TEST REPORT †[0]
0 = none; 1 = 24 hours; 2 = weekly; 3 = 30 days
(enter Test Code in field ✻64)
✱52 FIRST TEST REPORT OFFSET †[2]
0 = 24 hour; 1 = 6 hours; 2 = 12 hours; 3 = 18 hours
(Time to 1st report from power up/programming or downloading).
✱53 SESCOA/RADIONICS SELECT [0]
0 = Radionics (0–9, B–F reporting); 1 = SESCOA (0–9 only reporting).
Select 0 for all other formats.
✱54 LACK OF USAGE NOTIFICATION [0]
0 = Disabled 4 = 90 days
1 = 1 day 5 = 180 days
2 = 7 days 6 = 365 days
3 = 27 days
✱55 REPORTING CHANNELS
[0]
0 = Telco Line (no Radio)
1 = LRR/IP(Digital Communication only) and Telco Line
3 = LRR/IP (Digital Communication only) (no Telco Line)
5 = LRR/IP (Digital Communication with AAV) (Telco Line connections
for 2-way voice session only, if applicable)
✱56 ENHANCED ZONE PROGRAMMING See procedure in this guide and refer to the Installation Guide.
✱58 RF JAM DETECT [0]
0 = no RF Jam Detection; 1 = RF Jam Detect on, no CS report;
2 = RF Jam Detect on with CS report
(if trouble/restore report is enabled in fields ✻60, ✻71)
Note: For event logging option 2 must be selected.
† Entering a number other than the one specified may give unpredictable results.

- 7 -
Field Function Programmed Values [ ] = Table 1 Default Value
TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (✱59–✱76, & ✱89):
With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, 0, B, C, D, E, or F. Enter "#+10" for 0, "#+11" for
B, "#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F.
A "0" (not "#+10") in the first box will disable a report.
A "0" (not "#+10") in the second box will result in automatic advance to the next field when programming.
With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.
A "0" (not "#+10") in the second box will eliminate the expanded message for that report.
A "0" (not "#+10") in both boxes will disable the report.
With Ademco Contact ID Reporting: Enter any digit (other than "0") in the first box, to enable zone to report (entries in the
second boxes will be ignored).
A "0" (not "#+10") in the first box will disable the report.
Examples: For Code 3(single digit), enter: 3 | 0
For Code 3 2 (two digits), enter: 3 | 2
For Code B 2 (Hexadecimal), enter: #+11 | 2
SYSTEM STATUS REPORT CODES (✱59–✱68)
✱59 EXIT ERROR REPORT CODE [1]
✱60 TROUBLE REPORT CODE | [1,0]
✱61 BYPASS REPORT CODE | [0,0]
✱62 AC LOSS REPORT CODE | [0,0]
✱63 LOW BATTERY REPORT CODE | [1,0]
✱64 TEST REPORT CODE | [1,0]
✱65 OPEN REPORT CODE †† [0]
✱66 ARM AWAY/STAY REPORT CODE †† [0,0]
AWAY STAY
✱67 RF XMTR LOW BATTERY REPORT
CODE | [1,0]
✱68 CANCEL REPORT CODE | [1,0]
RESTORE REPORT CODES (✱70–✱76)
✱70 ALARM RESTORE REPORT CODE [1]
✱71 TROUBLE RESTORE REPORT CODE | [1,0]
✱72 BYPASS RESTORE REPORT CODE | [0,0]
✱73 AC RESTORE REPORT CODE | [0,0]
✱74 LOW BAT RESTORE REPORT CODE | [1,0]
(†† 2nd digit is automatically sent as the user
number if expanded or 4+2 reporting is
selected.)
2nd digit is automatically sent as 2nd digit of the zone alarm
report code programmed in ✻56, if expanded or 4+2 reporting
is selected.
2nd digit is automatically sent as 2nd digit of the zone alarm
report code programmed in ✻56, if expanded or 4+2 reporting
is selected.

- 8 -
Field Function Programmed Values[ ] = Table 1 Default Value
✱75 RF XMTR LO BAT RST RPT CODE | [1,0]
✱76 TEST RESTORE RPT CODE | [0,0]
DYNAMIC SIGNALING FIELD ✻
✻✻
✻77
✱77 DYNAMIC SIGNALING DELAY/
DYNAMIC SIGNALING PRIORITY
| [0, 0]
1st Entry (delay before switch CS reporting path)
0 = Redundant reporting
on dialer and LRR/IP
device
7 = 105 seconds
8 = 120 seconds
9 = 135 seconds
1 = 15 seconds #10 = 150 seconds
2 = 30 seconds #11 = 165 seconds
3 = 45 seconds #12 = 180 seconds
4 = 60 seconds #13 = 195 seconds
5 = 75 seconds #14 = 210 seconds
6 = 90 seconds #15 = 225 seconds
2nd Entry
0 = Primary Dialer Preferred Channel
1 = LRR/IP Preferred Channel
2 = LRR/IP reporting only
✱78 PROGRAMMABLE TONE
GENERATION TIME | [0, 0]
00 = Disabled
01-09 = 100-900 ms
10-99 = 1.0 – 9.9 secs.
OUTPUT AND SYSTEM SETUP (✱80–✱92)
✱80
✱81
DEVICE PROGRAMMING MENU
MODE
ZONE LISTS MENU MODE
Program ✻80 and ✻81 only if Powerline Carrier Devices or
chime by zone are to be used. See procedure later in this
manual.
✱83 ENHANCED SEQUENTIAL MODE See procedure later in this manual.
✱84 ASSIGN ZONE VOICE DESCRIPTOR
See procedure later in this manual.
✱85 RECORD CUSTOM VOICE
DESCRIPTOR
See procedure later in this manual.
✱86 MULTI-MODE (E-MAIL
NOTIFICATION) [0]
0 = Disable multi-mode devices
1 = Enable multi-mode device address #6 only
2 = Enable multi-mode device address #7 only
3 = Enable multi-mode addresses
✱87 AUX FUNCTION/ 1-BUTTON PAGING [0]
0 = Aux key performs defined function (macro);
1 = Aux key sends message to pager or voice message to follow me
system phone number.
If 1, you must also select an option 6-9 in field ✻49 for the pager or
10-13 for the follow me system announcement.

- 9 -
Field Function Programmed Values[ ] = Table 1 Default Value
✱88 PAGER CHARACTERS
Up to 16 digits can be entered that will appear in front of the 7-digit
pager message sent by the control (either upon system event or upon
pressing AUX key [if programmed for paging]; see field ✻87 and ✻49
for other options regarding the paging feature). See the Installation
Instructions (fields ✻87, ✻88 and ✻49) for full descriptions of the
paging feature. You do not need to fill all 16 digits (press [✻] to
advance to next field). To clear entries, enter ✻88✻.
To enter “✻” = [#] + [11]; To enter “#” = [#] + 12]
To enter 2-second pause = [#] + [13] (some pagers require an
additional delay [pause] in order to receive the entire message)
✱89 EVENT LOG 80% FULL RPT CODE | [0,0]
✱90 EVENT LOGGING [3]
0 = None; 1 = Alarm/Alarm Restore; 2 = Trouble/Trouble Restore;
4 = Bypass/Bypass Restore; 8 = Open/Close.
Example: To select “Alarm/Alarm Restore”, and “Open/Close”, enter
9 (1 + 8); To select all, enter #15.
Note: System messages are logged when any non-zero selection is made.
✱91 ALARM AUDIO VERIFICATION
(AAV)/REMOTE PHONE CONTROL [2]
0 = None
1 = AAV and remote phone control
2 = remote phone control only
4 = AAV only
Notes: (1) In order to activate the Remote Phone Control feature and defeat
an answering machine, ensure that the correct ring detection
count (“15”) has been programmed in field ✻95.
(2) Remote phone session will be terminated if a report must be
sent.
(3) Alarm Audio Verification will only function when Contact ID® is
selected. AAV cannot be used for UL installations.
(4) If an alarm will be reported to primary and secondary phone
numbers, AAV can only function via the secondary number.
(5) If an alarm will be reported to a pager (6-8 in field ✻49), or to
follow me phone number (10-12 in field ✻49) AAV cannot be
used.
(6) If AAV is selected and LRR/IP communications device is enabled,
you must enter "0" (primary dialer preferred channel) as the second
entry in Field *77.
✱92 NUMBER OF REPORTS IN ARMED
PERIOD [0]
0 = 10 Alarm/Alarm Restore Reports;
1 = Unlimited (UL installations = 0)
DOWNLOAD INFORMATION (✱93, ✱94, ✱95)
✱93 FLEXIBLE CALLBACK [0]
0 = No flexible callback; 1 = Last digit flexible; 2 = Last 2 digits
flexible;
3 = Last 3 digits flexible

- 10 -
Field Function Programmed Values [ ] = Table 1 Default Value
✱94 DOWNLOAD PHONE NUMBER
Enter up to 20 digits, 0–9; #+11 for '✻'; #+12 for '#'; #+13 for a
pause. Do not fill unused spaces. If fewer than 20 digits entered,
pressing ✻advances to the next field. To clear entries from field,
press ✻94✻.
Note: In UL installations, downloading may only be performed if a technician
is at the site.
✱95 RING DETECT COUNT FOR
DOWNLOADING/REMOTE PHONE
CONTROL MODE
[15]
0 = Disable Station Initiated Download; 1–14 = number of
rings (1–9, [#]+10 =10, [#] +11 =11, [#] +12 =12, [#] +13
=13, [#] +14 =14); 15 = answering machine defeat ([#] +15
=15)
✱96 INITIALIZE DOWNLOAD ID &
SUBSCRIBER ACCOUNT
No entry required
✱97 SET ALL PROGRAM FIELDS TO
1 OF 4 SETS OF DEFAULT VALUES
Enter 1-4 to select from default tables 1-4
Enter 0 to abort.
✱98 EXITS PROGRAMMING MODE
(PREVENTS RE-ENTRY)
If ✻98 is used to exit programming mode, you cannot enter the
Installer Code + 8+ 0 + 0 for re-entry. You must press "✻" and
"#" within 50 seconds of power up or from exiting Programming
mode to re-enter Programming mode.
Note: After exiting Program mode, the system takes up to 1 minute to reset.
To bypass the reset delay, press [#] + [0].
✱99 EXITS PROGRAMMING MODE
(ALLOWS RE-ENTRY)
Installer Code + 8 + 0 + 0
or:
Power-up, then press "✻" and "#" within 50 seconds of power
up or from exiting Programming mode.
Note: After exiting Program mode, the system takes up to 1 minute to reset.
To bypass the reset delay, press [#] + [0].