Mimosa Silverleaves 3191962 User manual

8-1
READ & SAVE BELOW INSTRUCTIONS BEFORE ASSEMBLY
!
1. PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU HAVE ALL OF THE PARTS LISTED.
2. TO AVOID ANY SCRATCHES DURING ASSEMBLY, ASSEMBLE ON A SOFT MAT OR SIMILAR.
3. ASSEMBLE STEP BY STEP FOLLOWING THE INSTRUCTIONS.
4. WASHERS MUST BE USED.
5. DURING ASSEMBLY DO NOT OVER FASTEN SCREWS & NUTS.
6. DO NOT COMPLETELY TIGHTEN EACH SCREW AND NUT UNTIL THEY ARE ALL FIXED IN PLACE.
SILVERLEAVES 3-SEATER
RESIN WICKER SWING
ASSEMBLY INSTRUCTION
Item No. 3191962

A
B
C
D
E
CODE PARTS QTY.
HARDWARE LIST
1PC
1PC
8-2
4PCS
2PCSM6x70mm
M6x67mm
M6x20mm
M8x47mm
M8x20mm
2PCS
4PCS
F
G
4PCS
1PC
1PC
1PC
2PCS #11
#13
#14
#15
#16
#17
2PCS
2PCS
2PCS
2PCS
#12 2PCS
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
1PC
1PC
1PC
1PC
CODE PARTS QTY.
PARTS LIST
1PC
1PC
1PC
1PC
CODE PARTS QTY.
PARTS LIST
1PC
H
Foot tube Short pole
Long pole
Spring hanger
Seat cushion
Canopy frame
Canopy
Rotary knob
Left front tube
Right back tube
Left back tube
Right front tube
Back tube
Beam
Seat frame
Right armrest
Bolt&washer&cap
Bolt&washer&cap
Bolt&washer&cap
Bolt&washer&cap
Bolt&washer&cap
Allen key
Allen key
Spanner
Left armrest

8-3
D
E
Using bolt(D) to attach the top beam(#7)
to the frame.
Attach the back tube(#6) to the frame,
using bolt(E).
Attach two left tubes(#2&4) to the left
foot tube, same steps with the right
side.

8-4
5
6
#11
#12
#8 #9
A
1
3
4
#10
2
C
B
B
#13
#12
#11
!
Attach long & short poles(#11&12) to the seat
frame(#8), then secure right & left
armrest(#9&10) to the seat frame(#8) as well,
using bolt(A,B&C). Noted that the leak hole in
poles should face inside.
Attach poles(#11&12) to spring hangers(#13),
then secure spring hangers to the beam(#7)
to combine the two frame part.

8-5
7
8
#15
#17
#15
#17
#16
Attach canopy frame(#15) to the whole
bracket, using bolt(#17).
Attach the canopy(#16) to the canopy frame,edges
should be curled in to fix the canopy.

8-6
9
10
#14
Attach seat cushion(#14) to the seat frame,
using ties with it to secure.
The main frame is now assembled at this stage.
To improve the assembly of the canopy follow
remaining steps below.

8-7
#17
11
13 14
12
1
2
152
For left side of canopy: spin the rotary knob(#17) to
loose canopy.
Pull canopy to the right angle as needed. Secure the rotary knob to fix the canopy.
Then adjust the canopy to right position.
1
2

8-8
CARE AND CLEANING:
1. TO CLEAN, WIPE WITH DAMP CLOTH. DO NOT USE BLEACH, ACID SOLVENTS OR ABRASIVE CLEANERS ON RESIN WICKER OR FRAME PARTS.
2. DURING VARYING WEATHER CONDITIONS AND WINTER PERIOD, WE STRONGLY RECOMMEND THAT THE SWING BE STORED IN A DRY AREA
WITH A SUITABLE COVER. BEFORE STORAGE, PLEASE INSURE THE SWING IS CLEAN AND DRY.
3. IN THE EVENT OF BARE METAL SHOWING DUE TO SCRATCHES, IT IS RECOMMENDED TO TREAT WITH A RUST REPELLING PAINT OR SIMILAR.
4. PERIODICALLY CHECK AND ENSURE THAT ALL THE SCREWS ARE COMPLETELY TIGHTENED.
5. A FURNITURE COVER IS STRONGLY RECOMMENDED TO EXTEND THE USAGE LIFE-SPAN.
17 18
16
1
2
1
#17
15
For right side, follow same four steps below as doing with left side to
secure canopy. Now your swing is ready for use.
1
2
Not For Commercial Use