Mimosa CORAL BAY LOUVRE PANEL GAZEBO User manual

CORAL BAY LOUVRE PANEL GAZEBO
Assembly Instructions
Item Number: 0177358
•Before installing please contact your local council for semi permanent structure requirements.
•For permanent fixture contact your local council and use appropriate fixings.
•This gazebo is a Semi-Permanent structure. Damage caused by extreme weather conditions including heavy rain or high winds is not
covered under warranty.
•Please carefully read all instructions before assembly and use.
•Please separate and identify all parts, ensuring that you have all parts listed.
•To avoid damage to your gazebo, it is recommended that you assemble it on a clean, protected surface.
•Washers must be used when indicated during the assembly process.
•Loosely tighten the nuts and then securely tighten when all are in position. Be careful not to over tighten the nuts during assembly.
•As an added precaution we strongly recommend you tighten any loose components after an initial period of use (around 3-6 months).
For assured longevity and safe use of your gazebo, we recommend regular checking and tightening of any bolts.
IMPORTANT SAFETY INSTRUCTIONS
•The ground for erecting and anchoring the gazebo is required to be a level, solid and a safe surface.
•Beware of existing utilities underground.
•Keep away from any electrical installations and transportation devices.
•Never climb, sit, or stand on the structure.
Please carefully read the below warnings and instructions.
Save the instructions for future reference.
!

Roof frame
Leg tube
Roof frame
Supporting frame
Louvre adjustment Component Centre
Louvre Adjustment Component Edge
Roof frame
Shutter
Shutter
Leg tube
Louvre Adjustment Component Edge
Incline Stabiliser Brace
Incline Stabiliser Brace
Roof Edge Panel
Roof Edge Panel

Cover plate
Leg base cover
Inclined connection plate
Handle
Washer
Spacer Washer
Inclined Bracket
Corner Bracket
Angled Connection Bracket
Supporting Plate
Supporting Plate
Handle loop
Drainage Cover
Drainage Cover

M6 x 18mm Bolt
Allen key
M6 x 39mm Bolt
Stake
M4 x 18mm Bolt
ST4.2 x 12mm Screw
Hook
M6 x 35mm Bolt
M6 x 30mm Bolt
Screw driver
Spanner

X3
M
X1
X4
Connect the leg base covers (M) to the leg tubes (A &A1)
using bolts (AA). Tighten securely using Allen key (JJ)
Screw the hook(DD) into the leg tube(A1).

X2
X8
Connect supporting plates (N&N1) to the leg tubes (A & A1),
using bolts (AA). Tighten securely using Allen Key (JJ).

X12
Insert the angled connection bracket (L) into the two
edge louvre adjustment components (D1 & D2).
Tighten the bolts (AA) using Allen Key (JJ)
Repeat the above process for the opposite
Connect the supporting frame (C) and the
edge louvre adjustment components (D1 & D2)
with bolts (AA). Tighten securely with Allen Key
(JJ).

STEP 04
厂M6*18 趴§旬
7
Secure the leg tubes (A & A1) to the edge louvre
adjustment components (D1 & D2) using bolts (AA).
Repeat for the other end.
X2

A
B
A
AA
A
HH
B
Align the roof frame (B) between the two leg tubes and
connect using bolts (HH). Tighten securely using Allen
Key (JJ).
Connect roof frame(B) and leg tubes with the incline stabiliser
braces (G &G1), using bolts (CC) & (AA). Tighten securely using
Allen Key (JJ).

AA
AA
H
H
Repeat on both sides
Connect the roof frame (B1)
and the leg tubes with the
incline stabiliser braces (G&
G1), using bolts (CC and
AA). Tighten securely using
Allen Key (JJ).
Join the inclined connectio
n
plates (P) to the roof frame
(B1) using bolt (AA).
Connect the two roof frames (B1) to the
leg tubes, using bolts (HH).
Then connect the incline stabiliser braces
(G & G1) to the roof frame (B1), using
bolts (CC). Tighten securely using Allen
key (JJ).
AA

A
A
A
A
Connect two pieces of roof
frame(B1) and leg tube with
bolt(HH) and tighten
Connect the roof frame
(B1)and leg tube with the
four incline stabiliser
braces (G & G1), using
bolts (CC & AA).Tighten
securely using Allen Key
(JJ).

A
A
Cover the roof frame (B
& B1) with the corner
brackets (K1) using
screws (EE) and
screwdriver (KK). Refer
image below.
Attach the roof frame (E) to the
louvre adjusting components (D1
&D2), using bolts (AA). Tighten
securely using Allen key (JJ).

FFM4*18
AA
BB
FF
FF
Insert the inclined bracket (K) into the centre louvre adjustment
component (D) and secure using bolts (AA & BB). Tighten securely using
Allen Key (JJ).
Attach the handle loop (Q) to the protruding parts on the lower end
of the centre louvre adjustment component (D), using bolts (FF).
Tighten securely using screwdriver (KK).

AA
AA
AA
Attach the centre louvre adjustment
component (D) to the roof frame (E & B1), using
bolts (AA). Secure the other end of D to the
inclined connection plate (P) using bolts (AA).
Tighten securely using Allen Key (JJ).

BB
S1
F1 F1
D
BB
S1
F1
D1
BB S1
F1
D1
Secure the shutter (F1) to the edge louvre adjustment component (D1) with
bolt (BB) and washer (S1). Secure the other end to the centre louvre
adjustment component (D) in the same way.

J
S2
E
BB J1
S2
E
J
BB
J1
S2
S1
S1 S1
BB
Place the spacer washers (S2)
between the roof frame (J & E).
Place the cover plate (J1) on the
roof frame (J) and after aligning
the holes secure with bolt (BB)
and washer (S1). Repeat for the
other holes.

1 2
R
Before installing the shutter (F), use the handle (R) to rotate the
louvre arms from position 1 to position 2 (as pictured above).

F
F
Insert the shutter(F) as shown, place the edge of the shutter(F)to
the tip of the bayonet,then push shutter down until it clicks into
place.

Q2
Q2
AA
AA
H
AA
H
Q1
Q1
AA H
D
AA H
As shown, connect edge adjusting component D1 or D2 with roof frame(H), cover
leaking hole(Q2), align the hole, and tighten the bolt(AA)
Tighten the bolt(AA)

Your gazebo is now fully assembled. If your gazebo is located on a
grassed surface, use the stakes (GG) to secure it in position (as
pictured).
•Before installing please contact your local council for semi permanent structure requirements.
•For permanent fixture contact your local council and use appropriate fixings.
•This gazebo is a Semi-Permanent structure. Damage caused by extreme weather conditions including heavy rain or high winds is not covered under warranty.
•Please carefully read all instructions before assembly and use.
•Please separate and identify all parts, ensuring that you have all parts listed.
•To avoid damage to your gazebo, it is recommended that you assemble it on a clean, protected surface.
•Washers must be used when indicated during the assembly process.
•Loosely tighten the nuts and then securely tighten when all are in position. Be careful not to over tighten the nuts during assembly.
•As an added precaution we strongly recommend you tighten any loose components after an initial period of use (around 3-6 months). For assured longevity and safe use of your
gazebo, we recommend regular checking and tightening of any bolts.
IMPORTANT SAFETY INSTRUCTIONS
•The ground for erecting and anchoring the gazebo is required to be a level, solid and a safe surface.
•Beware of existing utilities underground.
•Keep away from any electrical installations and transportation devices.
•Never climb, sit, or stand on the structure.
Please carefully read the below warnings and instructions.
Save the instructions for future reference.
!