Mincey Marble Manufacturing SD-08 User manual

1
Installation Instructions for Mincey Marble Manufacturing’s
Chrome Plated Wire Corner Mount Soapdish
Product number: SD- 08
Please read the following before attempting to install your new
chrome plated wire corner mount soapdish
These instructions have been written for Mincey Marble’s SD-08 chrome plated wire
corner mount soapdish. If you have received a different product than shown, please
contact our office so we can send proper instructions to you.
SD- 08
In preparation, before installing the soapdish, you will need to have completed the
installation of the panel system and sealed the seams of the shower behind where the
soapdish is to be installed with 100% silicone.
Tools and Materials required:
1. Torpedo level
2. Drill with ¼” masonry drill bit
3. 3 plastic wall anchors, stainless screws and mounting brackets (included in each box,
with wire soapdish)
4. 3 ea. clear plastic washers and chrome plated plastic screw caps (packaged separately
and included in your shipment)
5. #2 Phillips head screwdriver
6. Pencil
Mincey Marble Mfg., Inc.
1940 New Harvest Road
Gainesville, GA 30507
Ph: 800.533.1806
Fx: 770.531.0935
www.minceymarble.com

2
Drill Hole Locations for Installation
Back Panel
Side Panel
Mounting Hardware Included
Note:
Installing the wire corner soapdish:
1. Determine the height of the soapdish before going any further. It would be best to check
blue prints and with the project manager before drilling any holes. Failure to do this could
cause unnecessary repair work, which can be time consuming and costly. Also, make
sure the soapdish is being installed in the correct corner.
2. Once the height of the soapdish is determined, make a pencil mark on the wall where
the top of it will be installed. Using the torpedo level, continue this line on the adjacent
wall in the corner.
3 The soapdish has three mounting brackets. One is located on the longer side, and the
other two are located on the short side.
Please Note: If the soapdish is to be installed in the right corner, facing the shower,
the long side of the soapdish will be on the back wall and the short side will be on the
right shower panel. If the soapdish is to be installed on the left corner, facing the
shower, the long side of the soapdish will be on the left wall and the short side will be
on the back wall. (See diagram of soapdish)

3
4. For the longer side of the soapdish, measure back from the corner 6”, along the level
line marked on the wall. For the short side, measure two holes, one 3 3/8” and the other
4 7/8” from the corner. Drill these holes with a ¼” masonry bit.
5. Lightly tap the wall anchors into the ¼” diameter holes. Do not hit hard or damage could
occur to the panels.
6. Clean the pencil marks off the walls with acetone or other cleaner and a clean rag.
7. The mounting brackets have a wider end. This goes against the wall. It is easier to push
the screws through the clear plastic washer, open side facing the screw head and then
through the pre-drilled holes in the soapdish and place the mounting brackets on the
screws.
8. Carefully align the screws and the clear plastic washers with the wall anchors and start
the screws by hand. Hand-tighten the screws into the wall anchors, using the #2 Phillips
head screwdriver. Do not over-tighten. (Over– tightening the screw can distort the
clear plastic washer, causing the cap to not fit properly). For proper tightness, the
soapdish should be secure against the mounting brackets and not loose and “flopping”
on the wall.
9. Press the chrome plated screw cap onto the washer until it snaps into place.
Failure to carefully follow these instructions could cause the holes to be drilled in
the wrong locations.
If you have any questions, please call Mincey Marble Customer Service at 800.533.1806.