Mine TAN.HANDY User manual

TAN.HANDY
HAND HELD SPRAY TAN MACHINE
PRODUCT DATA & USER GUIDE

TAN.HANDY SPRAY TAN MACHINE
COMPONENTS LIST
TAN.HANDY SPRAY TAN MACHINE
ASSEMBLY GUIDE
QTY PARTS
Tan.Handy Spray Tan Machine
Excess 3 Spray Tan Applicator
Power Cord
1
1
1
1 x Tan.Handy Spray Tan Mini Turbine
3. To begin, attach the Tan.
Handy spray tan gun to
the Tan.Handy mini turbine
by inserting the bottom of
the handle of the spray
tan gun into the connector
of the mini-turbine.
4. Attach the Tan.Handy
spray tan gun with the
‘quick-connect’ style
tting. This will lock the
spray tan gun rmly into
place.
1. Un-screw the external solution cup away from the Handy.Tan and ll
desired amount of spray solution. We recommend lling it a minimum of
half way for best results. Over lling the solution cup may cause leaks.
2. Screw Cup back into the Handy.Tan. Ensure it is fully tightened so no
leaks occur
5. Insert the power cord into the de-
vice and in the wall plug and turn
power on at the wall switch.
1 x Excess 3 Spray Tan Applicator
1 x Power Cord
6. To remove the Tan.Handy mini-
turbine for cleaning and relling
solution cup, detach the spray gun
with the ‘quick-connect’ tting and
remove it from the mini-turbine.
SETTING SPRAY PATTERN
SPRAYING SIDE TO SIDE
ACROSS THE BODY
SPRAYING UP &
DOWN THE BODY
Adjusting the spray-pattern nozzle of your Tan.Handy to suit your preferred
style of spray tanning.
Set the nozzle fan Vertical. This spray
pattern setting is perfect for spraying up
and down, top to bottom of the body.
Set the nozzle fan ‘Horizontal ’. This spray
pattern is perfect for spraying side to side
ie. le to right – right to le across the body.
1. Prior to tanning, make sure
you exfoliate your skin in the
shower using the Exfoliating
Mitt. Exfoliating allows for a
smoother application as well
as helping the tan to fade
evenly.
2. Be sure skin is completely
clean and dry. Do not
apply any moisturisers, oils,
deodorants or perfumes prior
to use. Waxing or shaving
should also be done at least
24 hours prior to tanning.
3. Put hair up and cover with
plastic cap, remove all
jewelery.

TAN.HANDY SPRAY TAN MACHINE
OPERATION
IMPORTANT! We recommend doing this over a sink or towel.
1. Turn the device ‘on’ by pressing the on switch. The Tan.Handy has an
intelligent Air-Smart Switch, so with just turning it on, it controls the airow for
the perfect spray. This creates awless spray tanning results every time.
1. Holding the Tan.Handy approximately 10 -15cm (4 - 6”) away,
start at the feet and work up, using sweeping, steady motions,
keeping the Tan.Handy moving at all times as holding in one
spot too long may result in dark spots.
If a dark spot occurs, smooth our immediately with the
Application Mitt and continue spraying. Work your way up the
entire body, making sure to get complete and even coverage.
Avoid spraying directly your heels, knees, and elbows to prevent
deeper tanning in these areas.
For best results refer to MineTan’s A Picture Perfect Finish, How to
Spray Tan
recommended spray tan poses’ for the perfect spray tan.
2. Allow tan to dry before wearing clothing. Follow your preferred
product instructions for best results when applying the spray tan.
Avoid swimming or exercising, for the next 24 hours.
EXTERNAL SOLUTION CUP
SPRAY TAN TECHNIQUE
Rinse your solution cup with warm water until clean. Wipe all areas dry ready for the next use.
Please note: We recommend washing your cup under water, each time you remove the cup
from the handy tan and rell. If you have spilled the contents of the cup and product gets in
the screwband (grooved area of the cup being screwed into the HandyTan) simply wipe the
grooves with Tan.Easy Cleaning Wipes or a wet cloth/paper towel. This will allow the cup to be
easily tightened back onto the Tan.Handy and cause the cup not to leak excess spray solution.
1. Remove the hose from the Excess 3 Tan Applicator.
2. Unscrew the cup from the Applicator and empty any
un-used solution from the cup.
3. Rinse the empty solution cup with warm water until clean and
then ll the cup about ¼ full of warm water.
4. Insert the cup and screw tightly, back into the Applicator and
re-connect the hose.
5. Turn on your spray tan machine and adjust your solution Flow
Control dial to the highest setting for maximum water spraying.
6. Direct the spray applicator into the sink and spray the clean
water through until the cup is empty. This will clean through
the needle and out to the spray-pattern nozzle.
7. Now that the cup is empty, re-set your solution Flow
Control dial on the back of the Tan.Handy to your
regular settings.
8. Disconnect the Applicator from the Air-Hose and unscrew the cup.
9. Wipe all areas dry including the cup and Handy.Taready
for the next use. IMPORTANT! You must not submerge the Applicator under water. If
there is any excess spray tan solution, wipe down with clean wipes.
Alternately you can use a smooth cloth (avoid anything abrasive) with
a general glass cleaner to maintain the gloss nish.
SETTING SOLUTION AIR-FLOW CONTROL
The solution Flow Control dial
on the back of the applicator
will determine how much
solution will be dispensed
from the gun. You can
adjust the ow of solution
by adjusting the dial on the
handle.
The higher number on your
dial, the more solution will
ow from the Tan.Handy.
As you become more
comfortable with your spray
tan techniques, you can
increase the ow of your
solution.
INCREASE
SOLUTION
DECREASE
SOLUTION
MAXIMUMMAXIMUM
SOLUTIONSOLUTION
FLOWFLOW 66
1
5
4
3
2
1
MINIMUMMINIMUM
SOLUTIONSOLUTION
FLOWFLOW
TAN.HANDY SPRAY TAN MACHIN
CLEANING & MAINTENANCE
POWER ON: AIRFLOW
ON/OFF
The Tan.Handy Filter is
located at the front of the
unit as pictured below.
IMPORTANT! Please
disconnect from supply
circuit before cleaning or
removing lters.
1. Remove the lter cover
from the mini turbine.
2. Wash under cold water. Do
not use detergents to clean
the lter.
3. Please leave to dry
completely.

TAN.HANDY SPRAY TAN MACHINE
WARNING & SAFETY
IMPORTANT SAFETY PRECAUTIONS
Before using the Tan.Lite, read all instructions and cautionary markings in this manual and on the device.
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
1. Do not leave product unattended when plugged in. Unplug from outlet when not in use and before servicing.
2. Do not use outdoors or on wet surfaces.
3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.
3. This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
4. Use this device only for its intended function and do not use attachments not recommended by the authorized MineTan
manufacturer.
5. Do not use the device if the cord is damaged. In the event of damage discontinue use immediately. If the supply cord is
damaged, it must be replaced by the authorized MineTan manufacturer.
6. If device is not working as it should, has been dropped, damaged, le outdoors, or dropped into water, do not use, contact
MineTan Customer Care via the website or regional telephone number.
7. Do not pull or carry by cable, use cable as a handle, close a door on cable, or pull cable around sharp edges or corners. Keep
cable away from heated surfaces.
8. Do not unplug by pulling on cable. To unplug, grasp the plug, not the cable.
9. Do not handle plug with wet hands.
10. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may
reduce air ow. Switch o and unplug the product before attempting to remove any blockage.
11. Turn o all controls before unplugging.
12. Do not spray ammable or combustible liquids, such as gasoline, or use in areas where they may be present.
13. Do not use without the lter in place.
14. Never look directly into the airow when device is in use.
15. Do not use an extension cord unless the cord complies with local regional electrical safety standards
16. Periodically inspect the power cord for signs of damage
SAVE THESE INSTRUCTIONS
This product is intended for professional use only.
Do not pull
on cable
Do not submerge in
water or get wet
Do not use near
open ames
FOR MORE INFORMATION
VISIT OUR WEBSITE FOR MORE INFORMATION
WWW.MINETANBODYSKIN.COM
TAN.HANDY SPRAY TAN MACHINE
WARRANTY & GUARANTEE
MINETAN GUARANTEE
1 YEAR TROUBLE FREE WARRANTY
Congratulations on your purchase. We trust you will be happy with your purchase as the products are designed to give you many
years of service. To activate your Guarantee, please complete the information within 30 days of purchase. This form has details of our
guarantee terms & conditions so please read it carefully, ll it in and return it to the address at the back of this manual. Alternatively
you can register online at minetanbodyskin.com. Keep this form, with your original proof of purchase for any claim under guarantee.
If you have any queries or require further information on your product please contact your local representative of Minetan Pro Tools
Products.
TO REGISTER YOUR EQUIPMENT OR LODGE A WARRANTY CLAIM PLEASE
VISIT MINETANBODYSKIN.COM/WARRANTY/
TERMS & CONDITIONS
If within one (1) year from the date of purchase, the product fails due to a defect in material or workmanship, we will repair if possible
or replace it free of charge with a comparable unit, which may be new or refurbished. This guarantee applies only to the original
purchaser and is not transferable. The goods must be returned to the seller with proof of purchase to be assessed at the purchasers
cost. Prior to making a claim, please ensure you have read all trouble-shooting questions at minetanbodyskin.com. If there is a defect
with the device, it will be replaced free of charge with a comparable unit. Guarantee shall not apply to any defect, failure or damage
caused by improper use or improper or inadequate maintenance and care. The manufacturer shall not be obligated under this
guarantee:
1. To repair damage resulting from attempts by personnel other than authorized representatives to install, repair or service the product.
2. To repair damage, malfunction, or degradation of performance resulting from improper use or incompatible solution.
3. To perform maintenance or cleaning or to repair damage, malfunction, or degradation of performance resulting from failure to
perform user maintenance and cleaning as prescribed.
4. To repair damage, malfunction, or degradation of performance resulting from use of the product in an environment not meeting
the operating specications.

© 2019 MineTan. All rights reserved.
MarqLabs, 291 Edgewood Street, Alexandria. TN. 37012
Email: [email protected] Phone: AUST: 1300 819 331 USA: 1800 914 3880 EU/UK: [phone]
minetanbodyskin.com