Minuteman Endeavor RTXL Series User manual

User's Manual
Endeavor 5 - 10KVA
RTXL UPS Series
Para Systems, Inc.
1455 Lemay Dr.
Carrollton, TX 75007
Phone: [phone]
Fax: [phone]
Internet: minutemanups.com
UPS Sizing: sizemyups.com
PN - 34000471 R2

1
1. Introduction 2
2. Controls and Indicators 6
3. Installation 9
4. Operation 15
5. Configurable Parameters & Settings 21
6. Troubleshooting 22
7. Obtaining Service 24
8. Specifications 25
9. Limited Product Warranty 27
A1. Declaration of Conformity 28
Table Of Contents

3
2
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS !
WARNING: RiskofElectricalShock. Hazardousliveparts inside thesepower
supplies are energized from the battery even when the AC input is discon-
nected.
WARNING: This Uninterruptible Power Supply contains potentially hazard-
ous voltages. Do not attempt to disassemble the UPS beyond the battery
replacement procedure. This UPS contains no user serviceable parts. Re-
pairs and Battery replacement must be performed by QUALIFIED SERVICE
PERSONNELONLY.
Chapter 1: Introduction
Thankyou for purchasing this powerprotectionproduct. It has been designed
and manufactured to provide many years of trouble free service. Please read
this manual before installing your Endeavor Series UPS, models ED5000RT-
CU,ED6000RT-CU,ED8000RT-CUandED10000RT-CUas itprovidesimpor-
tantinformation that shouldbefollowed during installation andmaintenance of
theUPS system allowing you to correctly setupyour system for the maximum
safety and performance. Included is information on customer support and
factory service if it is required. If you experience a problem with the UPS
system please refer to the Troubleshooting guide in this manual to correct the
problem or collect enough information so that the Technical Support Depart-
ment can assist you.
CAUTION! TheED5000RT-CUand ED6000RT-CUcome withan input power
cord in the box. Connect the UPS to a two pole, three wire, groundedAC wall
outlet. The outlet must be connected to the appropriate branch protection
(circuit breaker). Connection to any other type of outlet may result in a shock
hazard and violate local electrical codes. TheAC wall outlet shall be installed
nearthe UPS andshallbe easily accessible. Theplugon the inputpowercord
on this UPS series is intended to serve as a disconnect device. Do not use
extension cords, adapter plugs, or surge strips. The installation of upstream
and downstream protective devices is highly recommended when the UPS is
connected to the mains and the load.
CAUTION! TheED8000RT-CUand ED10000RT-CUare hardwire input only.
The pins for the input and output cables are included. The UPS must be
connectedto the appropriatebranch protection (circuitbreaker)to avoid shock
hazard and violation of any local electrical codes. The branch protection
(circuitbreaker) shall be installednear the UPS and shallbe easily accessible.
The installation of upstream and downstream protective devices is highly rec-
ommended when the UPS is connected to the mains and the load.
CAUTION! To reduce the risk of electrical shock with the installation of this
UPS equipment and the connected equipment, the user must ensure that the
UPS is properly grounded due to a possible risk ofAC current leakage.
CAUTION! This UPS series is ONLYintended to be installed in an indoor
temperature controlled environment that is free of conductive contaminants.
This UPS series is not intended for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/Data Processing Equip-
mentANSI/NFPA75.
CAUTION! Themaximum ambient operating temperature for this UPS series
is 40°C (“0 ~ 40°C” for Ambient Operation).
Theexternal vents and openings on the UPS areprovidedfor ventilation.
Toensure reliable operationofthe UPS and to protect theUPSfrom over-
heating,these ventsand openings mustnot be blockedor covered. Donot
insert any object into any of the vents or openings that may hinder the ve-
ntilation.
Installthe UPS systemin a wellventilated area, awayfromexcess moistu-
re,heat, dust, flammable gas or explosives.
Leaveadequate space (atleast 15cm) aroundallsides of theUPS system
forproper ventilation.
Do not mount the UPS system with its front or rear panel facing down at
any angle.
Before usage, you must allow the UPS system to adjust to room temper-
ature (20°C~25°C or 68°F~77°F) for at least one hour to avoid moisture
condensing inside the UPS.
WARNING: Qualified Service Personnel ONLY must perform the Installa-
tion and Servicing of these UPS systems. MINUTEMAN accepts no liabilities
and is not limited to: injury to the Service Personnel, or damages to; the UPS,
the Battery Pack, or the connected equipment caused by the incorrect instal-
lation or servicing of the UPS system. There are optional isolation step-down
transformers(XFR) andMaintenanceBypass Switches (MTBS)for these UPS
systems. TheseUPSs MUST beoperated with theirrespectiveBattery Packs,
seethe table below:
BP240RTXL
UPS ED8000RT-CU
ED10000RT-CU
BP BP192RTXL
ED5000RT-CU
ED6000RT-CU
ED8000RT-XFR
ED10000RT-XFR
XFR ED5000RT-XFR
ED6000RT-XFR
ED-MTBS12K
MTBS ED-MTBS12K

5
4
LIFE SUPPORT POLICY
As a general policy, Para Systems does not recommend the use of any of our
productsin life support applicationswhere failure or malfunctionofthe product
can be reasonably expected to cause failure of the life support device or to
significantlyaffect itssafety or effectiveness. Wedo not recommendthe useof
any of our products in direct patient care. We will not knowingly sell our prod-
uctsfor use in such applications unless it receives inwritingassurances satis-
factoryto usthat(a) therisks of injuryor damage havebeen minimized, (b) the
customer assumes all such risks, and (c) our liability is adequately protected
under the circumstances.
Once you receive the product it should be visually inspected for damage that
may have occurred in shipping. Immediately notify the carrier and place of
purchase if any damage is found. Warranty claims for damage caused by the
carrier will not be honored by the manufacturer. The packing materials that
the product was shipped in were carefully designed to minimize any shipping
damage. In the unlikely case that the product needs to be returned to the
manufacturer, use the original packing material. Since the manufacturer is
not responsible for shipping damage incurred when the product is returned,
the original packing material is inexpensive insurance. PLEASE SAVE THE
PACKING MATERIALS!
RECIEVING INSPECTION
NOTICE: This equipment has been tested and found to comply with the limits for
a Class B computing device in accordance with the specifications in Subpart J of
Part 15 of FCC Rules and the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference of the Canadian Department of Com-
munications. These limits are designed to provide reasonable protection against
such interference in a residential installation. This equipment generates and uses
radio frequency and if not installed and used properly, that is, in strict accordance
with the manufacturer's instructions, this equipment may cause interference to ra-
dio and television reception. If this equipment does cause interference to radio or
televisionreception, which can be determined by turning the equipmentoff and on,
theuseris encouraged to tryto correct the interferenceby one or moreof the follow-
ing measures:
Re-orientthe receiving antenna.
Relocate the computer with respect to the receiver.
Move the computer away from the receiver.
Plug the computer into a different outlet so that the computer and receiver
are on different branch circuits.
Shielded communications interface cables must be used with this product.
WARNING: Changes or modifications to this unit not expressly approved by the
partyresponsibleforcompliancecouldvoidtheuser's authority to operate the equip-
ment.
ON / OFF / TEST BUTTON: Turning the input circuit breaker (on the
rear panel) to the on position will put the UPS in the Bypass mode and
supply power to the load. Press, hold and then release the On/Off/Test
Button during the audible alarm's first beep to turn the inverter on and
transferthe UPS to the On-Line mode. When theUPS isOn, press, hold
and then release the On/Off/Test Button during the audible alarm's sec-
ondbeeptoturntheinverter off and transfer theUPStotheBypassmode.
Toturnthe UPS offturnofftheinputcircuit breaker onthe rear panel,wait
for approximately 1-minute until the LCD and the fans turn off, and then
turnoff the DCbreaker(s) on therear panel ofthe Battery Pack(s). When
the UPS is in the On-Line mode or the Economy mode, press, hold and
thenreleasethe On/Off/TestButton during theaudiblealarm's forth beep.
TheUPSwill perform a10-second SelfTest. Duringthe test, the UPSwill
switch to the Battery mode, the On-Battery icon will illuminate and the
audible alarm will sound. If the UPS fails the test, one of the icons will
remain illuminated indicating the type of problem. The UPS will charge
the batteries while the UPS is in the Bypass mode, the On-Line mode or
the Economy mode when there is acceptableAC voltage present.
© COPYRIGHT 2014 BY PARA SYSTEMS, INC.
AllRights Reserved.Allrightsofthis User Manual(“Manual”),including but not
limited to the content, information, and figures are solely owned and reserved
by Para Systems, Inc. (“Para Systems”). The Manual can only be applied to
the operation or the use of this product.Any disposition, duplication, dissemi-
nation, reproduction, modification, translation, extraction, or usage of this
Manual in whole or in part is prohibited without the prior written permission of
ParaSystems. Giventhat ParaSystems willcontinuously improveanddevelop
the product, changes may be made to the information in this Manual at any
time without obligation to notify any person of such revision or changes. Para
Systems will make all possible efforts to secure the accuracy and the integrity
of this Manual. Para Systems disclaims any kinds or forms of warranty, guar-
antee,or undertaking, either expressly or implicitly,including but not limited to
thecompleteness, faultlessness, accuracy,non-infringement, merchantability
or fitness for a particular purpose of the Manual.
CAUTION! To de-energize the outputs of the UPS:
1. If the UPS is on press and release the On/Off/Test button after the second
beep.
2. Turn off the input circuit breaker on the rear panel of the UPS.
3. Turn off the DC breaker(s) on the rear panel of the Battery Pack(s).
4. Disconnect the UPS from theAC source.
5. To completely de-energize the UPS, disconnect the battery cable.

7
6
TheACnormal icon illuminateswhenthe UPS is onand operating in
theACnormal mode. TheACnormalicon willextinguishwhen oper-
ating in the Battery mode.
The On-Battery icon illuminates when the UPS is operating in the
Batterymode. The On-Batteryicon will extinguishwhen operating in
theAC normal mode.
The Weak/Bad Battery icon illuminates when the UPS detects a
weakbattery, badbattery orif thebatteryisdisconnected. TheWeak/
BadBatteryiconisextinguished whenthe battery'scondition isgood.
The Fault icon illuminates when the UPS detects an internal fault.
The Fault icon is extinguished when the UPS is operating properly.
TheLoad Level Bar Graph operates as follows:
LED #1: When the attached load is >20% the LED will illuminate.
LED #2: When the attached load is >40% the LED will illuminate.
LED #3: When the attached load is >60% the LED will illuminate.
LED #4: When the attached load is >80% the LED will illuminate.
LED #5: When the attached load is >100% the LED will illuminate.
When the amount of load attached to the UPS exceeds 110% of its
powerrating; the Overload icon will flash OffandOn, all of the LEDs
in the Load Level Bar Graph will be illuminated and the UPS will
sound a constant alarm to indicate an Overload condition.
The Battery Capacity Bar Graph operates as follows:
LED #1: When the battery capacity is >20% the LED will illuminate.
LED #2: When the battery capacity is >40% the LED will illuminate.
LED #3: When the battery capacity is >60% the LED will illuminate.
LED #4: When the battery capacity is >80% the LED will illuminate.
LED #5: When the battery capacity is >100% the LED will illuminate.
TheMulti-FunctionOn/Off/TestButtonfunctionsasfollows:
Turning the input circuitbreaker(on the rearpanel)totheonpositionwill
put the UPS in the Bypass mode and supply power to the load. Press,
holdand then releasethe On/Off/TestButtonduring theaudible alarm's
first beep to turn the inverter on and transfer the UPS to the On-Line
mode.
Whenthe UPS is On, press,hold andthen releasethe On/Off/TestBut-
ton during the audible alarm's second beep to turn the inverter off and
transfer the UPS to the Bypass mode. To turn the UPS off turn off the
input circuit breaker on the rear panel, wait for approximately 1-minute
untiltheLCDandthefansturnoff, and then turn offtheDCbreaker(s)on
therear panelof the Battery Pack(s).
When the UPS is in the On-Line mode or the Economy mode, press,
holdand then releasethe On/Off/TestButtonduring theaudible alarm's
forthbeep.TheUPS will performa10-second SelfTest. Duringthetest,
the UPS will switch to the Battery mode, the On-Battery icon will illumi-
nateandtheaudiblealarmwillsound. IftheUPS fails the test, oneofthe
iconswill remainilluminated indicating the type of problem.
PressingtheAlarm Silencer Buttonwhile theunit is operatingin Battery
mode, will silence the audible alarm. Once the UPS reaches the LBW
(LowBatteryWarning)thresholdthealarmwillbere-activated. Thealarm
cannot be silenced during the LBW alarm. Once the UPS transfers to
theAC mode the alarm will be reset to default.
TheScroll Button allows the user to scroll through the UPS parameters
that are available on the LCD screen.
CONTROLPANEL
Chapter 2: Controls and Indicators
NOTE: The LCD backlight will illuminate for 1-minute when the UPS switches to
the Battery mode. When the UPS has an event and/or an error code the LCD
backlightwill turn on and remainon toalert theuser that an event has occurred.
TheLCD will report the following information:
INPUT: Voltage,frequency,KVA,KW.
OUTPUT: Voltage, frequency, KVA, KW.
EstimatedRuntime: In thenormalAC mode and the Battery mode.
Error codes: The UPS will display error codes if an error occurs.
bPS: The UPS is operating in the Bypass mode.
EPo: The Emergency Power Off function is being performed.
ECo: The UPS is operating in the Economy mode.

9
8
INSTALLATION PLACEMENT
This UPS series is ONLYintended to be installed in an indoor temperature
controlledenvironment thatisfree ofconductive contaminants. DO NOToper-
ate the UPS in: extremely dusty and/or unclean areas, locations near heating
devices, water or excessive humidity, or where the UPS is exposed to direct
sunlight. Selecta location,which willprovidegood aircirculation fortheUPS at
all times. Route power cords so they cannot be walked on or damaged. This
UPS series is not intended for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/Data Processing Equip-
mentANSI/NFPA75.
Operating Temperature (Maximum): 0 to 40°C (+32 to +104°F)
Operating Elevation: 0 to 2,000m (0 to +6,562 ft)
Operatingand StorageRelative Humidity: 95%,non-condensing
Storage Temperature: -15 to +50°C (+5 to +122°F)
Storage Elevation: 0 to 15,000m (0 to +49,213 ft)
INSTALLATION
Besure to read the installationplacement and all the cautionsbeforeinstalling
theUPS system. Place the UPS in the final desiredlocationand complete the
rest of the installation procedure. These UPSs do not have internal batteries
and must be connected to at least one Battery Pack to operate properly. See
the “Rackmount Configuration” to install the UPS into the rack and see the
“Connecting the Battery Pack” procedure to connect the Battery Pack. USE
CAUTION: The UPS and Battery Pack are extremely heavy. Use the appro-
priatenumber of personnel when installing the UPS system.
CAUTION! DO NOT USE THE MOUNTING BRACKETS TO LIFT THE UPS.
The mounting brackets are ONLYfor securing the UPS to the rack.
1. The Parallel port is used for communication between two UPSs and the
Maintenance Bypass Switch (MTBS) for parallel operation.
2. The Charger Detection port connects to an external charger.
3. The RS232 communications port is for UPS monitoring and control.
4. The Smart slot is used for mini option cards.
5. The Input Circuit Breaker will trip in the event the load exceeds the UPS’s
powerrating.
6. The InputTerminal Block is for connecting the input utility power.
7. The OutputTerminal Block is for connecting the load.
8. The External Battery Connector is for connecting the Battery Packs.
9. The Fan provides airflow for the UPS.
10. TheRemote Control port is used to remotelyshutdownthe UPS.
11. The SNMP slot is used for option cards.
REAR PANELS Chapter 3: Installation
NOTE: If you are using more than one Battery Pack with this UPS series, the
UPS must be configured so that the UPS will report the correct estimated
runtime on the LCD screen and in the Power Monitoring software and/or the
SNMP card. See the Power Monitoring software or the SNMP card’s User’s
Manual to configure the UPS.

11
10
RACKMOUNT CONFIGURATION
Use the included rackmount brackets and screws to mount the UPS in a rack
byfollowing the stepsbelow.
USE CAUTION: The UPS system is heavy. Use the appropriate number of
personnelwhen installing theUPSsystem.
CAUTION! DO NOT USE THE MOUNTING BRACKETS TO LIFT THE
UPS. The mounting brackets are ONLYfor securing the UPS to the rack.
1. Attach the rackmount brackets to the mounting holes on the side panel of
theUPS as shown below.
TOWER CONFIGURATION
The tower configuration allows the user to install the UPS in the up-right posi-
tion. The tower stands are provided with the UPS. WARNING: Use two or
more people when installing the UPS. Use CAUTION, the UPS system is
extremelyheavy.
1. Oncethe location of the UPS has been determined, place thetowerstands
in the desired location.
WARNING: The UPS must be installed in the proper up-right position. Once
the UPS is placed in the tower stands, looking at the front panel the top cover
of the UPS MUST be on your left hand side.
2. Slide the UPS into the tower stands. Make sure that the UPS is stable.
3. The LCD panel can be rotated to read in the up-right position. Remove the
front panel from the UPS. On the backside of the front panel, push the
LCDpanel outwards, the panel will popout. Rotate the LCD panel counter
clockwise so that it reads in the upright position. Re-install the front panel
on the UPS.
NOTE: See the Battery Pack User's Manual to install the Battery Pack.
2. Follow steps 1 through 4 to install the UPS into the Rail kit. See the figure
below.
Step 1: Adjust the length of the rail according to the rack.
Step 2: Securely tighten the wing nuts.
Step 3: Secure the rail to the rack with the enclosed screws.
Step 4: Slide the UPS onto the rail and secure to the rack with the enclo-
sed screws.
NOTE: See the Battery Packs User's Manual to install the Battery Pack.
CONNECTING THE BATTERYPACK
(QUALIFIEDSERVICEPERSONNELONLY)
Please read all of the WARNINGS and CAUTIONS before attempting to con-
nect or service the batteries or the Battery Pack. The installation and servic-
ing of the batteries and the Battery Pack must be performed by Qualified
Service Personnel ONLY.
Replace the batteries and/or Battery Pack with the same number and type as
originallyinstalled.
CAUTION: Donot open or mutilate batteries. Released electrolyte isharmful
to the skin and eyes and may be toxic.
CAUTION: Do not dispose of batteries in a fire. The batteries may explode.

13
12
CONNECTING THE UPS TO AN AC SOURCE
1. When connecting the UPS to the utility power and the load, it is recomme-
ndedthat you install the protective devices. Theprotectivedevices should
beapproved components that meet safety certifications.
2. Prior to applying power to the UPS, ensure the UPS is properly grounded.
3. The utility power for the UPS must be single-phase in accordance with its
rating label and the specifications in this manual.
The ED5000RT-CU and ED6000RT-CU come with an input power cord in the
box. The#10AWG input power cord is 10ftlongandhas an L6-30Pplug on it.
Connectthe UPS toa two pole,three wire, groundedAC walloutlet. The outlet
must be connected to the appropriate branch protection (circuit breaker).
Connectionto any other typeofoutlet may result inashock hazard and violate
local electrical codes. TheAC wall outlet shall be installed near the UPS and
shall be easily accessible. The plug on the input power cord on this UPS
series is intended to serve as a disconnect device. Do not use extension
cords, adapter plugs, or surge strips. The installation of upstream and down-
streamprotective devices is highlyrecommended when the UPS isconnected
to the utility power and the load.
SuggestedProtection Device
ED5000RT-CU 5KVA
Model#
ED8000RT-CU
ED10000RT-CU
ED6000RT-CU 6KVA
8KVA
10KVA
C curve- 40Amp
D curve- 63Amp
D curve- 63Amp
PowerRating
C curve- 40Amp
1. The UPS MUST be in the off position.
2. The DC breaker(s) on the rear panel of the Battery Pack(s) MUST be in
the off position.
3. Remove theExternalBatteryConnector's cover plate from the rear panel
of the UPS (requires a phillips screwdriver).
4. Remove the topExternalBattery Connector's cover plate from the rear
panel of the Battery Pack.
5. Connect theoneendof the #8AWG premolded battery cabletothe Exter-
nal Battery Connector on the rear panel of the UPS and secure with the
retaining screws.
6. Connect theother end of the#8AWG premolded batterycableto the Exte-
rnal Battery Connector on the rear panel of the Battery Pack and secure
with the retaining screws.
7. See the Battery Pack User's Manual for more detailed information.
CAUTION: Thebattery can present a riskof electrical shock. These batteries
produce sufficient current to burn wire or tools very rapidly, producing molten
metal. Observethese precautions when installing or replacing the batteries:
1. Remove watches,rings,or other metal objects.
2. Use handtools with insulatedhandles.
3. Wear protective eye gear (goggles), rubber gloves and boots.
4. Do not lay tools or other metal parts on top of batteries.
5. Disconnect the charging source prior to connecting or disconnecting the
batteryterminals.
6. Determine if the battery is inadvertently grounded. If the battery is, rem-
ove the source of the grounding. Contact with any part of a grounded ba-
ttery can result in an electrical shock. The likelihood of such shock will be
reduced,if suchgrounds are removedduring installation andmaintenance.
WARNING: This UPS series does not haveinternalbatteries. ABatteryPack
MUST beconnected to theseUPSsso that theywillprovide battery backup for
theconnected load.
NOTE: See the Battery Pack User's Manual for more detailed information.

15
14
Chapter 4: Operation
SYSTEM OVERVIEW
Thisdouble conversionOn-Line UPS protectscomputers, servers, telecommuni-
cations and electronic equipment from blackouts, brownouts, overvoltages, and
surges. ThisOn-LineUPS converts the inputACtoDCand then back toa true sine
waveAC output. The true sine wave output is regulated within 2% of the nominal
outputvoltage. ThePowerFactorCorrection (PFC) circuitrycorrectstheinputpower
factortowithin99% of unityandblocksthe load generatedharmonicdistortion from
getting back on the input AC line. This On-Line UPS provides a continuous true
sine wave output with zero transfer time and great regulation to protect your mis-
sion critical equipment. The UPS will quietly and confidently protect your system
frompower anomalies.
The UPS will charge the batteries when the UPS is in the On-Line, the Bypass, or
Economy modes as long as the UPS is connected to utility power and there is an
acceptable AC voltage present. When a blackout, brownout, or an overvoltage
conditionoccurs while the UPS is in the On-Line mode or the Economy mode; the
UPSwilltransfertothebatterymode, the On-Battery indicator willilluminateandthe
audiblealarm will sound once every ten-seconds indicating that the utility poweris
lostorunacceptable. Whenthe utility powerreturnsoris at anacceptablelevel,the
UPS will automatically transfer back to the On-Line mode or the Economy mode
and start recharging the batteries. During an extended outage when there is ap-
proximately two-minutes of backup time remaining the audible alarm will sound
twice every five-seconds. This Low Battery Warning is letting the user know that
they should save all open files and turn off their equipment. When the batteries
reachthe predetermined level the UPS will automaticallyshutdown protecting the
batteries from over discharging. Once the utility power returns the UPS will auto-
maticallyrestartproviding safe usablepower to theconnected equipment andstart
rechargingthe batteries.
TheBypass modeoperation: The inpututility power'bypasses' the inverter circuit
and is connected directly to the output of the UPS powering the connected equip-
mentwhile simultaneously charging the batteries. When a blackout, brownout, or
an overvoltage condition occurs while the UPS is in the Bypass mode the con-
nected equipment will not be backed up. When utility power returns the UPS will
automaticallystartup inthe Bypassmode poweringthe connectedequipment and
resumecharging the batteries.
The Economy mode operation: The input utility power 'bypasses' the inverter cir-
cuit and is connected directly to the output of the UPS powering the connected
equipmentwhile simultaneously charging the batteries. When a blackout,brown-
out, or an overvoltage condition occurs the UPS will transfer to the battery mode,
theinverterwillturnonpoweringtheconnected equipment, the On-Battery indicator
will illuminate and the audible alarm will sound once every ten-seconds indicating
thatthe utilitypower islost orunacceptable. When theutility powerreturns oris at
anacceptablelevel, the UPSwillautomatically transfer backtothe Economy mode
andstart rechargingthe batteries.
INPUT / OUTPUT CONNECTIONS:
1. Remove the terminal block cover box from the rear panel of the UPS (req-
uiresa phillips screwdriver). Refer to the figure below for the input /output
connections.
2. Input / Output cable selection:
60°C / 75°C
Temperature Rating 5/6KVA
#10 AWG (Cu)
8/10KVA
#6 AWG (Cu)
(In accordance with National Electrical Code (NEC), install suitable cond-
uit and bushing.) NOTE: Use copper wire only.
3. Before connecting to the input / output terminals read all of the Cautions
and Warning, then observe the following:
a) Ensure that the UPS is turned off and not connected to theAC sour-
ce or the battery source before any connections are made.
b) Calculate the power consumption of the load to ensure that an over-
load condition does not occur.
c) Ensure that the terminal block screws are secured after connecting
the input / output wires. The terminal block screws should be torque
to 18±2Kgf.cm (requires a 3/16" flat-head screwdriver).
d) Ensure that the UPS is properly grounded.
4. Connect the input utility wires and/or input power cord to the input termi-
nal block and secure.
5. Connect the load wires to the output terminal block and secure.
6. Re-install theterminal block cover box.
TheED8000RT-CUand ED10000RT-CUare hardwire input only. Thepins for
the input cable are included. The UPS must be connected to the appropriate
branch protection (circuit breaker) to avoid shock hazard and violation of any
local electrical codes. The branch protection (circuit breaker) shall be in-
stalled near the UPS and shall be easily accessible. The installation of up-
stream and downstream protective devices is highly recommended when the
UPS is connected to the utility power and the load.

17
16
ON / OFF / TEST BUTTON
Turning the input circuit breaker (on the rear panel) to the on position will put
the UPS in the Bypass mode and supply power to the load. Press, hold and
thenrelease theOn/Off/TestButtonduringthe audible alarm'sfirst beep toturn
the inverter on and transfer the UPS to the On-Line mode. When the UPS is
On, press, hold and then release the On/Off/Test Button during the audible
alarm's second beep to turn the inverter off and transfer the UPS to the By-
pass mode. To turn the UPS off turn off the input circuit breaker on the rear
panel,wait for approximately 1-minute until the LCD and the fans turnoff, and
then turn off the DC breaker(s) on the rear panel of the Battery Pack(s).
When the UPS is in the On-Line mode or the Economy mode, press, hold and
thenrelease the On/Off/TestButton duringtheaudible alarm's forth beep.The
UPSwill perform a 10-second SelfTest. Duringthetest,the UPS will switch to
theBattery mode, the On-Battery icon willilluminateand the audible alarm will
sound. Ifthe UPS failsthetest, one of theicons will remain illuminatedindicat-
ing the type of problem. The UPS will charge the batteries while the UPS is in
the Bypass mode, the On-Line mode or the Economy mode when there is
acceptableACvoltagepresent.
START-UP IN THE AC MODE:
The UPS must be connected to utility power and there must be an acceptable
AC voltage present. The Battery Pack(s) must be connected to the UPS and
the DC breaker(s) on the rear panel of the Battery Pack(s) must be in the on
position.
1. Turnonthe input circuit breaker on therear panelof the UPS. The fans will
turn on, theAC normal icon will flash off/on and the LCD will display ‘bPS’.
The UPS is now in the Bypass mode. NOTE: If there is a power interrup-
tion while the UPS is in the Bypass mode the load will not be backed up.
START-UP IN THE BATTERYMODE:
The Battery Pack(s) must be connected to the UPS and the DC breaker(s) on
the rear panel of the Battery Pack(s) must be in the on position.
1. Turn on the input circuit breaker on the rear panel of the UPS.
2. Press, holdand then release theOn/Off/Test Button duringthe audible ala-
rm's first beep to transfer the UPS to the Battery mode.
3. The fans will turn on, then the UPS will start-up and perform a self-diagno-
sis for approximately 10-seconds. The following items are checked:
a) Since there isno input voltage present,theUPS will automatically sel-
ect the default value for the output frequency (the default value is
60Hz). NOTE: If the UPS had been previously connected to an input
source of 50Hz then the output frequency will be 50Hz.
b) The LCD displays input voltage, battery capacity bar graph, and the
battery mode icon will be flashing.
c) Auto checks the rectifier.
d) Auto checks the charger.
e) Auto checks the battery.
f) Auto checks the DC BUS voltage.
g) Auto teststhe inverter.
Block Diagram of the Basic Wiring and Internal Circuit Configuration
Output
2. Turn on the connected equipment one at a time.
3. Press, holdandthen release the On/Off/Test Button during theaudibleala-
rm's first beep to transfer the UPS to the On-Line mode.
4. The UPS will start-up and perform a self-diagnosis for approximately 10-
seconds. The following items will be checked:
a) The UPS will auto detect the input frequency to determine the output
frequency (the default value is 60Hz).
b) Displays input voltage, load capacity and battery capacity.
c) Auto checks the rectifier.
d) Auto checks the charger.
e) Auto checks the battery.
f) Auto checks the DC BUS voltage.
g) Auto teststhe inverter.
h) If all the test passsuccessfullythen the UPS will transfer to the On-Li-
ne mode. NOTE: If any of the test fail an error code will be display-
yedand the UPS will remain in the Bypassmodeor the UPS will shut-
down depending on the type of error.
TURNING OFF THE UPS IN THE AC MODE:
1. Press, holdandthen release the On/Off/Test Button during theaudibleala-
rm's second beep to transfer the UPS to the Bypass mode.
2. Turn off all of the connected equipment.
3. Turn off the input circuit breaker on the rear panel of the UPS.
4. Wait for approximately 1-minute until the LCD and the fans turn off.
5. Turn off the DC breaker(s) on the rear panel of the Battery Pack(s).

19
18
h) If all the test pass successfully (takesapproximately 15-seconds to
complete) then the UPS will transfer to the Battery mode. NOTE: If
any of the test fail an error code will be displayed and then UPS will
shutdown.
4. Turn on the connected equipment one at a time.
TURNING OFF THE UPS IN THE BATTERYMODE:
1. Turn off all of the connected equipment.
2. Press, holdandthen release the On/Off/Test Button during theaudibleala-
rm's second beep to turn the UPS off.
3. Turn off the input circuit breaker on the rear panel of the UPS.
4. Wait for approximately 1-minute until the LCD and the fans turn off.
5. Turn off the DC breaker(s) on the rear panel of the Battery Pack(s).
NOTE: If you are using more than one Battery Pack with this UPS series, the
UPS must be configured so that the UPS will report the correct estimated
runtime on the LCD screen and in the Power Monitoring software and/or the
SNMP card. See the Power Monitoring software or the SNMP card’s User’s
Manual to configure the UPS.
START-UP IN THE ECONOMY MODE (ECo):
The UPS must be connected to utility power and there must be an acceptable
AC voltage present. The Battery Pack(s) must be connected to the UPS and
the DC breaker(s) on the rear panel of the Battery Pack(s) must be in the on
position. The Economy mode must be Enabled by using either the SNMP
card or the Power Monitoring software.
1. Turnon the input circuitbreakeron the rear panelof the UPS. The fans will
turn on, theAC normal icon will flash off/on and the LCD will display ‘bPS’.
The UPS is now in the Bypass mode. NOTE: If there is a power interrup-
tion while the UPS is in the Bypass mode the load will not be backed up.
2. The Economymode option mustbeEnabled through theSNMP card orthe
PowerMonitoring software.
3. Turn on the connected equipment one at a time.
4. Press, holdandthen release the On/Off/Test Button during theaudibleala-
rm's first beep to transfer the UPS to the Economy mode.
5. The UPS will start-up and perform a self-diagnosis for approximately 10-
seconds. If all the test pass successfully then the UPS will transfer to the
Economy mode and the LCD will display ECo. NOTE: If any of the test
fail an error code will be displayed and the UPS will remain in the Bypass
mode or the UPS will shutdown depending on the type of error.
TURNING OFF THE UPS IN THE ECONOMY MODE (ECo):
1. Press, holdandthen release the On/Off/Test Button during theaudibleala-
rm's second beep to transfer the UPS to the Bypass mode.
2. Turn off all of the connected equipment.
3. Turn off the input circuit breaker on the rear panel of the UPS.
4. Wait for approximately 1-minute until the LCD and the fans turn off.
5. Turn off the DC breaker(s) on the rear panel of the Battery Pack(s).
RS232 COMMUNICATIONS PORT
The RS232 communication port is a standard DB9 female. The pinout for the
port is depicted below:
Pin 2: /TXD
Pin 3: /RXD
Pin 5: Ground
All of the other pins are not used.
NOTE: Connecting to the RS232 port is optional. The UPS works properly
withoutthis connection.
POWER MONITORING SOFTWARE
The UPS comes with a Power Monitoring Software CD. See the software CD
for the installation of the Power Monitoring Software.
OPTION SLOT
The option slot on the rear panel of the UPS is for option cards. Contact your
local dealer for the available option cards.
RJ11 REPO (Remote Emergency Power Off) PORT
Connect one end of the RJ11 cable to the REPO port and the other end of the
RJ11 cable to the EPO switch. In the AC or the Battery mode short pin4 to
pin5 for approximately 0.5-seconds to shutdown the UPS. The UPS must be
turned off and then back on again to restart the UPS. NOTE: Connecting to
the REPO port is optional. The UPS works properly without this connection.
This connection is not for Telecommnication use.
PARALLELPORT
TheParallel port is used for communication between two UPSs and the Main-
tenance Bypass Switch (MTBS) for parallel operation. Only two UPSs can be
paralleled together. The paralleled UPSs MUSThave the same; model num-
ber,VA/Watt rating,voltageandfrequency.Thetotalload willbe sharedequally
by the two units. See the MTBS User's Manual for the configuration and the
setup for paralleling the units. NOTE: Connecting to the Parallel port is
optional. TheUPS works properly without this connection. Contact your local
dealer for more information.
CHARGER DETECTION PORT
The Charger Detection port on the rear panel of the UPS is for detecting an
external charger that is used to charge the Battery Packs. NOTE: Connect-
ingto the Charger Detection port isoptional. TheUPS works properly without
this connection. Contact your local dealer for the available options.

21
20
WEAK/BAD BATTERY
TheUPSautomaticallyteststhebattery’s conditionandwill illuminatetheWeak/
Bad Battery icon, an error code will be displayed and the audible alarm will
sound. This alarm will be repeated until the batteries pass a self test. If the
battery is weak, bad or disconnected, the Weak/Bad Battery icon will illumi-
nate,an error code will be displayed and the alarm will beepthreetimes every
five-minutes until the battery is either reconnected or replaced. It is recom-
mended that the UPS be allowed to charge overnight before performing a
battery test to confirm a Weak/Bad Battery condition.
OVERLOAD
When the amount of load attached to the UPS exceeds its power rating; the
Overload icon will flash Off and On, all of the LEDs in the Load Level Bar
Graph will be illuminated an error code will be displayed and the UPS will
sound a constant alarm. This alarm will remain on until the excess load is
removed or the UPS’s self protection circuit shuts the UPS down. If the UPS
shuts down because of an Overload condition, the UPS must perform an In-
verter function or a Self Test to clear the OverloadAlarm.
ALARMS
ON BATTERY
When the UPS is operating on the batteries, the On-Battery icon will illumi-
nate,the audiblealarmwill sound onceevery ten-seconds. The alarmwill stop
once the UPS returns to theAC normal mode.
LOW BATTERYWARNING
When the battery reserve runs low, the audible alarm will sound two beeps
every five-seconds and an error code will be displayed. This condition will
continue until either the AC returns or the UPS shuts down from battery ex-
haustion.
UPS FAULT
When the UPS detects a fault, the Fault icon will illuminate, the audible alarm
will sound a constant alarm, and an error code will be displayed. The fault
condition,in some instances, may be reset byturningthe UPS off and then on
again. NOTE: See the Troubleshooting section for a list of the error codes.
NOTE: TheLCD backlight will illuminate for 1-minute whenthe UPS switches
to the Battery mode. When the UPS has an event and/or an error code the
LCD backlight will turn on and remain on to alert the user that an event has
occurred.
(These items may require optional software or hardware)
Function Factory
Default Description
User Choices
Set
inverter
output
voltage
Shut-
down
Type
Set
audible
alarm
state
Enable/
Disable
auto
restart
Battery
lifein
days
Battery
install
date
UPS ID Endeavor
Series
Date of
manufacture
1826
Enabled
Enabled
EntireUPS
208VAC
Up to 64 charac-
ters to define the
UPS
Date of battery
replacement-
month/day/year
XX/XX/XXXX
Up to 5
characters
Enable
or
Disable
Enabled,at
lowbattery,
disabled
Entire UPS or
UPSoutput
220, 230,
240VAC)
At first battery replacement, re-
set to reflect actual number of
days experience in your environ-
ment or leave factory default.
Enterthe currentdate when
replacingbatteries.
Use this function to uniquely
identify the UPS in your network
configuration.
Changesoutputvoltage.
Enabled-theUPSwillemitashort
beep when in the battery mode.
AtLow Battery the UPS will emit
twobeepsfromlow batterywarn-
inguntil shutdown.
Disabled-Useonlywhensoftware
is controlling the UPS or to
silencethe alarm.
When enabled, the UPS will
automatically restart from a low
batteryshutdownwhennormalAC
returns.
Enable/
Disable
REPO
Disabled Enable
or
Disable
Enabled - the UPS will be
powered off and remain off until
the UPS is reset.
EntireUPS-Turns offtheentire UPS.
UPS Output - Turns off the UPS's
output receptacles only.
Chapter 5: Configurable Parameters
and Settings
Set
External
Battery
Pack
1 2 - 10 Configures the UPS so that it will
report the correct estimated
runtime on the LCD screen and
in the Power Monitoring software
and/or the SNMP card.
Enable/
Disable
ECo
Disabled Enable
or
Disable
Enabled- the UPS willoperate in
theEconomymode.

23
22
ErrorCode:E01. UPSisshut-
down.
Symptom / Error Code Cause / What To Do
Pressthe On/Off/Test buttonand release during the firstbeep.
UPS will not turn on. Resetthe inputcircuit breaker.If theinput circuitbreaker trips after
UPS restarts, reduce the load on the UPS.
UPSoperatesinbatterymode
only,eventhough thereisAC
present.
The AC normal icon is illumi-
nated, but there is no output. Disconnectthe computercable from theUPS, pressthe On button.
If UPS works normally, the software has control of the UPS.
Chargethe batteriesovernightand thenretest. If theruntime isstill
less than expected, the batteries may need to be replaced.
UPSdoes notprovide
expectedruntime. The UPShas aninternal problem.Call forservice.
Faulticon isilluminated anda
constantalarm.
Error Code: E02. Overload
iconis illuminatedand acon-
stant alarm.
Check the specifications and remove part of the load. If the UPS
shuts down because of an Overload, the UPS must perform an
Inverter function or a Self Test to clear the Overload Alarm.
The UPS has detected a short-circuit on its output. Check the at-
tachedload.
ErrorCode:E03. UPS isshut-
down. Theinternalor ambinettemperaturehasexceeded thetemperature
ratings. Check the specifications.
Error Code: E04. Input Over
CurrentProtection Warning. Checkthe specificationsand removepart ofthe load.
ErrorCode:E11:Inverter/Out-
putfailure shutdown. TheUPS hasan internalfault. Callfor service.
Error Code: E12. DC BUS
OVPShutdown. The UPShas aninternal fault.Call forservice.
Error Code: E13. Fan Fail
Warning. Thefan haseither failed orhas stoppeddue to exessivedirt. Ifthe fanhasfailed,callforservice.Ifthe fan isdirty,useacanof "Canned
Air" to clean the fan.
ErrorCode: E14.ChargerFail-
ureWarning. The chargerhas failed, callfor service.
Error Code: E15. The battery
needsto bereplaced. Charge thebatteries overnightand then retest.If theruntime isstill
less than expected replace the batteries and/or call for service.
ErrorCode: E17.Low
BatteryWarning. The UPS'sbattery reserveis low. Thiscondition will continue until
AC returns or the UPS shuts down from battery exhaustion.
ErrorCode: E18.Low
Battery Capacity.
ErrorCode:E05.Inputvoltage
orfrequency isout ofrange. The input voltage or frequency is out of range when the UPS is in the Bypass mode. Check the input source.
Error Code: E06. Ambient
OverTemperature Protection. Theinternal temperatureofthe UPShas exceededthe safe oper-
ating range for the UPS. Check the specifications.
TheUPS's batterycapacity islow. Chargethe batteries overnight.
Chapter 6: Troubleshooting
Error Code: E07. Ambient
Under Temperature Protec-
tion.
Theinternal temperatureof the UPShas exceededthe safeoper-
ating range for the UPS. Check the specifications.
Error Code: E08. Manual By-
pass is on. The external Maintenance Bypass Switch (MTBS) is in the on
position. Check the MTBS.
ErrorCode: E19.Bad
Battery. This could be a disconnected battery, a weak battery or a bad bat-
tery. Check the battery connections. Charge the batteries over-
night and if the error code is still there replace the batteries and/or
callfor service.
Error Code: E20. DC BUS
(high/low)failure.
Symptom / Error Code Cause / What To Do
ErrorCode:E21.Bypass SCR
ShortedFailure. The UPShas aninternal fault.Call forservice.
TheUPS hasan internalfault. Callfor service.
ErrorCode:E22.BypassSCR
OpenedFailure. The UPShas aninternal fault.Call forservice.
Error Code: E23. Input SCR
Failure. TheUPS hasan internalfault. Callfor service.
Error Code: E28: Input Fuse
Failure. TheUPS hasan internalfault. Callfor service.
ErrorCode:E29.Output Fuse
Failure. TheUPS hasan internalfault. Callfor service.
ErrorCode:E30.Chargerand
BatteryFailure. The UPShas aninternal fault.Call forservice.
Error Code: E31. System
ClockFailure. The UPShas aninternal fault.Call forservice.
ErrorCode:E32.ParallelCom-
munications Loss. Check the parallel cable connections at the UPS and the MTBS.
ErrorCode: E33.Parallel
UPSNot Compatible. Trying to parallel two differnet UPS models. When paralleling the
UPSs they must be the same model and VAratings. Call for ser-
vice.
ErrorCode:E24. OutputSCR
Failure. TheUPS hasan internalfault. Callfor service.
Error Code: E25. Input HVP
RelayShorted Failure. TheUPS hasan internalfault. Callfor service.
Error Code: E26. Input HVP
RelayOpened Failure. The UPS has an internal fault. Call for service.
ErrorCode:E27.NTCOpened
Failure. TheUPS hasan internalfault. Callfor service.

25
24
IF THE UPS REQUIRES SERVICE
1. Use theTroubleshooting section to eliminateobvious causes.
2. Verify there are no tripped circuit breakers and that the batteries are good.
A tripped circuit breaker and defective batteries are the most common iss-
ues.
3. Call your dealer for assistance. If you cannot reach your dealer, or if they
cannotresolve theissuecall orfaxtheTechnicalSupport departmentat the
following numbers; Voice phone [phone], FAX line [phone]
or visit our Web site at www.minutemanups.com the "Discussion Board".
Before calling the Technical Support Department have the following infor-
mationavailable:
a) Contact name and address.
b) Where and when the unit was purchased.
c) All of the model information about your unit.
d) The serial number of your unit.
e) Any information onthefailure, including LEDs that maybe illuminated
or error codes displayed.
f) A description of the protected equipment including model numbers, if
possible.
g) A technician will ask you for the above information and if possible,
helpsolve the issueoverthe phone. In the eventthat the unit requires
factory service, the technician will issue you a Return MaterialAutho-
rizationNumber (RMA #).
h) If the unit is under warranty, the repairs will be done at no charge. If
the unit is not under warranty there will be a charge for the repair.
4. Pack the unit in its original packaging. If the original packaging is no lon-
geravailable, ask the TechnicalSupportTechnician about obtaining a new
set. It is important to pack the unit properly in order to avoid damage in
transit. Never use Styrofoam beads for a packing material.
a) Include a letter with your name, address, day time phone number,
RMA number, a copy of your original sales receipt, and a brief desc-
ription of the problem.
5. Mark the RMA#on the outside of all packages. The factory cannotaccept
any package without the RMA # marked on the outside.
6. Return the unit by insured, prepaid carrier to:
Para Systems Inc.
MINUTEMANUPS
1809W. Frankford Road, Suite 150
Carrollton,TX75007
ATTN: RMA#_______
Chapter 7: Obtaining Service Chapter 8: Specifications
Default:208VAC,User selectable:220/230/240VAC
Protection
WaveformType
Over-Current,andShort-Circuit Protected
TrueSineWave
Frequency 50/60Hz,+/-0.1Hz
NominalVoltage
MaximumPower Capacity
0 ms
>90%(Full Load)
ResettableCircuit Breaker
40 to 70 Hz, autosensing
0- 300VAC 180- 280VAC
208VAC:204 -212VAC
TransferTime
Efficiency(On-Line Mode)
InputProtection
FrequencyLimits
VoltageRange
AcceptableInput voltage
ModelNumber
SYSTEMSPECIFICATIONS
VoltageRange
Topology DoubleConversion On-Line,TrueSineWave
OUTPUT ON-LINE OPERATION
INPUT
Numberof Phase Single (1∅2W +G)
NominalVoltage 208VAC
LowVoltageTransferPoint 156/180V resets to Utility Power at 166/190V or higher
HighVoltageTransferPoint 280V resets to Utility Power at 270V or lower
VoltageRegulation Nominal +/-2%
FrequencyRange 50/60Hz, +/-0.1Hz (unless synchronized to utility)
OUTPUT BATTERYOPERATION
VoltageRegulation Nominal +/-2%(until LowBattery Warning)
VoltageT.H.D. <2%(LinearLoad)
+/-5% @ 100% Load change in 30 msDynamicResponse
SlewRate <1Hz / second
OverloadCapacity >106% - <110%for 10-minutes
>111%- <125%for 5-minutes
>126%- <150%for 30-seconds
156- 280VAC
PowerFactor Correction >99% at Full Load
CrestFactor 3 : 1
5000VA
4500W 6000VA
5400W
ED10000RT-CU
8000VA
7200W 10000VA
9000W
ED8000RT-CUED6000RT-CUED5000RT-CU
2.7 : 1
NOTE: Specifications are subject to change without notice.

27
26
BATTERYSYSTEM
System Voltage 240VDC
Runtime:Full Load(minutes)
Runtime:Half Load(minutes) 14
11
5
3
SURGE PROTECTIONAND FILTERING
Audible Noise at 1 m (3 ft.)
NoiseFilter
Surgevoltage let-through(as a
percentage of an appliedANSI
C62.41 Cat. B +/-4 kV)
SurgeResponseTime
SurgeCurrent Capability
SurgeEnergy Rating 1050J
1.2 μs normal mode; <50 μs common mode
<10%
normaland commonmode EMI/RFI suppression
6500Amps total
ENVIRONMENTAL
OperatingTemperature (max)
Operating/StorageHumidity
OperatingElevation
0to 40°C(+32to +104°F)
0~ 95%Non-Condensing
0 to 2,000m (0 to +6,562 ft)
PHYSICAL
Weight - Net
Size - Net
L X W X H
Size - Shipping
L X W X H
Weight- Shipping
35.3 lbs
16.0 Kgs 46.5 lbs
21.1 Kgs
52.9 lbs
24.0 Kgs 65.0 lbs
29.5 Kgs
REGULATORYCOMPLIANCE
SafetyandApprovals
EMCVerification
cTUVus (Conforms to UL1778 4th Edition & CSA 22.2 no. 107.3-05)
FCC Class B, CE certified
Storage Elevation 0 to 15,000m (0 to +49,213 ft)
StorageTemperature -15 to +50°C (+5 to +122°F)
192VDC
12
4
12
4
<60 dBA
26.0 x 17.3 x 3.5"
660 x 440 x 88.5 mm
39.4 x 23.6 x 8.7"
1000 x 600 x 222 mm
24.6 x 17.3 x 5.14"
625 x 440 x 130.6 mm
39.4 x 23.6 x 9.8"
1000 x 600 x 246 mm
Typical RechargeTime 8-hoursto90% aftera fullload discharge
ParaSystems,Inc.(Para Systems) warrants thisequipment,whenproperlyappliedand
operated within specified conditions, against faulty materials or workmanship for a pe-
riod of three years from the date of purchase. For equipment sites within the United
Statesand Canada, this warrantycoversdepotrepairorreplacementofdefective equip-
mentatthediscretion of Para Systems. Depotrepairwillbefromthe nearest authorized
service center. The customer pays for shipping the product to Para Systems. Para
Systems pays ground freight to ship the product back to the customer. Replacement
partsandwarrantylaborwill be borne by Para Systems. For equipmentlocatedoutside
oftheUnitedStatesand Canada, ParaSystemsonlycoversfaultyparts. ParaSystems
products that are depot repaired or replaced pursuant to this warranty shall only be
warrantedfortheunexpired portion ofthewarrantyapplyingto the original product. This
warranty applies only to the original purchaser who must have properly registered the
productwithin10 days of purchase.
Thewarrantyshall be void if (a) the equipmentis damaged by the customer,isimprop-
erlyused,issubjected to an adverse operating environment, or is operated outside the
limitsofitselectricalspecifications;(b)theequipmentisrepaired or modified by anyone
otherthanParaSystemsorParaSystemsapprovedpersonnel;or(c)hasbeenusedin
amannercontrary to the product’s User's Manual or other written instructions.
Anytechnicaladvicefurnished before or after delivery in regard to use or application of
ParaSystems’equipmentis furnished without chargeandonthebasisthat it represents
Para Systems’ best judgment under the circumstances, but it is used at the recipient’s
solerisk.
EXCEPTASPROVIDEDHEREIN,PARASYSTEMS MAKES NO WARRANTIES,EX-
PRESSEDORIMPLIED,INCLUDINGWARRANTIESOFMERCHANTABILITYANDFIT-
NESSFORAPARTICULARPURPOSE. Some statesdo not permit limitationof implied
warranties;therefore,theaforesaidlimitation(s)may not apply to the purchaser.
EXCEPTAS PROVIDED ABOVE, IN NO EVENT WILL PARA SYSTEMS BE LIABLE
FORDIRECT, INDIRECT, SPECIAL,INCIDENTAL,ORCONSEQUENTIALDAMAGES
ARISINGOUTOFTHE USE OFTHIS PRODUCT, EVEN IFADVISEDOFTHEPOSSI-
BILITYOF SUCH DAMAGE. Specifically,ParaSystemsisnot liable for any costs,such
as; labor for on-site installation, on-site maintenance or on-site service, lost profits or
revenue,lossofequipment,loss of use of equipment,lossofsoftware,lossofdata, cost
ofsubstitutes, claims by third parties, orotherwise. The sole and exclusive remedy for
breachofany warranty,expressedorimplied, concerning Para Systems’products and
theonly obligation of Para Systems hereunder,shallbe depot repairorreplacementof
defective equipment, components, or parts; or, at Para Systems’ option, refund of the
purchase price or substitution with an equivalent replacement product. This warranty
givesyouspecificlegalrightsandyou may also have other rights which vary from state
tostate.
No employee, salesman, or agent of Para Systems is authorized to add to or vary the
terms of this warranty.
Chapter 9: Limited Product Warranty
8ms (Typical)
208VAC:187 -228VAC (240VAC:216 -264VAC)
TransferTime
OutputVoltageRange ECONOMY MODE OPERATION
LowVoltageTransferPoint At -10%of therated input voltage transferstothe On-Line mode
8-Volt hysteresis to reset to the Economy mode
HighVoltageTransferPoint
>96%(Full Load)
Efficiency(Economy Mode)
At+10% of the ratedinputvoltage transfers tothe On-Linemode
8-Volt hysteresis to reset to the Economy mode

29
28
A1. DECLARATION OF CONFORMITY
Application of Council Directive(s): 2004/108/EC
Standard(s) to which Conformity is declared:
Manufacturer’s Name: Para Systems, Inc. (MINUTEMAN UPS)
Manufacturer’sAddress: 1455LeMay Drive
Carrollton,Texas75007 USA
Type of Equipment: Uninterruptible Power Supplies (UPS)
ModelNo: ED5000RT-CU,ED6000RT-CU,ED8000RT-CU,ED10000RT-CU
I hereby declare that the equipment specified above conforms to the above
Directive(s).
Place:Carrollton, Texas,USA Date: April 1, 2014
RobertCalhoun
(Name) ManagerEngineering
(Position)
Year of Manufacture: Beginning April 1, 2014
EN 50091-2:1995 Class A, IEC61000-4-2: level4, IEC61000-4-3: level3,
IEC61000-4-4:level4,IEC61000-4-5:level4, IEC61000-4-6: level3,IEC61000-
4-8: level3, IEC 62040-1-1, IEEE C62.41 CategoryA1
Notes: