Minuteman Encompass EC1000RT2U User manual

User's Manual
Encompass RT
On-Line UPS Series
Para Systems, Inc.
1455 Lemay Dr.
Carrollton, TX 75007
Phone: [phone]
Fax: [phone]
Internet: minutemanups.com
UPS Sizing: sizemyups.com
PN - 34000519 R2

1
1. Introduction 2
2. Controls and Indicators 6
3. Installation 9
4. Operation 14
5. Configurable Parameters & Settings 19
6. Obtaining Service 20
7. Troubleshooting 21
8. Replacing the Battery 22
9. Specifications 25
10. Limited Product Warranty 27
A1. Declaration of Conformity 28
Table Of Contents

3
2
Thankyouforpurchasingthispowerprotectionproduct. Ithasbeendesigned
and manufactured to provide many years of trouble free service. Please read
this manual before installing your Encompass On-Line Series UPS, models
EC1000RT2U, EC1500RT2U,EC2000RT2U,EC3000RT2Uasitprovidesim-
portantinformationthatshouldbefollowedduringthe installation and themain-
tenance of the UPS system allowing you to correctly set up your system for
the maximum safety and performance. Included is information on customer
support and factory service, if it is required. If you experience a problem with
the UPS system please refer to the Troubleshooting guide in this manual to
correct the problem or collect enough information so that the Technical Sup-
port Department can assist you.
CAUTION! Themaximumambientoperatingtemperaturefor this UPS series
is 40°C (“0 ~ 40°C” for Ambient Operation).
Theexternalventsandopeningson the UPS are provided for ventilation.
ToensurereliableoperationoftheUPSandtoprotecttheUPSfromover-
heating,thesevents and openings must notbeblockedorcovered. Do not
insert any object into any of the vents or openings that may hinder the ve-
ntilation.
InstalltheUPS system in a well ventilated area,awayfromexcessmoistu-
re,heat,dust,flammablegasorexplosives.
Leave adequate space (at least 20cm) in the front and at the rear of the
UPSsystemfor proper ventilation.
Do not mount the UPS system with its front or rear panel facing down at
any angle.
Before usage, you must allow the UPS system to adjust to room temper-
ature (20°C~25°C or 68°F~77°F) for at least one hour to avoid moisture
condensing inside the UPS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS !
CONSIGNES DE SÉCURITÉ IMPORTANTES
SAUVEGARDEZ CES CONSIGNES!
Veuillezlire ce manuel avantl'installationde l'onduleurmodèlesEC1000RT2U,
EC1500RT2U, EC2000RT2U, EC3000RT2U. Il contient de l'information
importantequi doit être respectée au coursde l'installation et de l'entretien de
l'onduleur et des batteries. Cette information vous permettra de correctement
installerlesystèmepouratteindreson rendement maximum en toute sécurité.
Chapter 1: Introduction
WARNING: Risk of Electrical Shock. Hazardous live parts inside these
power supplies are energized from the battery even when the AC input is
disconnected.
CAUTION! To reduce the risk of electrical shock in conditions where the
load equipment grounding cannot be verified, disconnect the UPS from the
AC wall outlet before installing a computer interface cable. Reconnect the
power cord only after all signaling connections are made.
CAUTION! Connect the UPS to a two pole, three wire grounded AC wall
outlet. The receptacle must be connected to the appropriate branch protec-
tion (circuit breaker or fuse). Connection to any other type of receptacle may
result in a shock hazard and violate local electrical codes. Do not plug the
UPS into extension cords, adapter plugs or surge strips.
CAUTION! To reduce the risk of electrical shock with the installation of this
UPS equipment and the connected equipment, the user must ensure that the
combined sum of theAC leakage current does not exceed 3.5mA.
WARNING: ThisUninterruptible Power Supply containspotentiallyhazard-
ous voltages. Do not attempt to disassemble the UPS beyond the battery
replacement procedure. This UPS contains no user serviceable parts. Re-
pairs and Battery replacement must be performed by QUALIFIED SERVICE
PERSONNELONLY.
CAUTION! To reduce the risk of fire, connect only to a utility powered
circuit provided with 20 / 30 amperes maximum branch circuit over-current
protection in accordance with the National Electric Code,ANSI/NFPA70.
WARNING: Qualified Service Personnel ONLY must perform the Installa-
tion and Servicing of these UPS systems. MINUTEMAN accepts no liabilities
and is not limited to: injury to the Service Personnel, or damages to; the UPS,
or the connected equipment caused by the incorrect installation or servicing
of the UPS system.
CAUTION! This UPS series is ONLYintended to be installed in an indoor
temperature controlled environment that is free of conductive contaminants.
This UPS series is not intended for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/Data Processing Equip-
mentANSI/NFPA75.
NOTE: TheseUPSsareshippedwiththebatteriesdisconnected. Thebatter-
ies must be connected before putting these UPSs into service. Refer to Sec-
tion 3 "Installation" for connecting the batteries.
CAUTION! DO NOT USE THE MOUNTING BRACKETS TO LIFT THE
UPS. The mounting brackets are ONLYfor securing the UPS to the rack.

5
4
NOTICE: Thisequipmenthasbeentestedand found to comply with the limits
for a ClassAand/or B computing device in accordance with the specifications
in Subpart J of Part 15 of FCC Rules and the ClassAand/or B limits for radio
noiseemissions from digital apparatus set out in theRadio Interference of the
Canadian Department of Communications. These limits are designed to pro-
vide reasonable protection against such interference in a residential installa-
tion. This equipment generates and uses radio frequency and if not installed
and used properly, that is, in strict accordance with the manufacturer's in-
structions, this equipment may cause interference to radio and television re-
ception. If this equipment does cause interference to radio or television re-
ception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
followingmeasures:
Re-orientthe receiving antenna.
Relocatethecomputerwithrespect to the receiver.
Movethecomputer away from the receiver.
Plugthecomputerintoadifferent outlet so that the computer and receiver
areondifferentbranchcircuits.
Shieldedcommunicationsinterface cables must be used with this product.
WARNING: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user's authority to
operatetheequipment.
ON BUTTON: When the UPS is connected to an AC source and
there is an acceptableAC voltage present; Press and then release
theONbutton after the audible alarm beeps twice to turn the UPS
on and power the load.
DC START:Press and then release the ON button after the au-
dible alarm beeps twice. Then within 10-seconds press and then
release the ON button after the audible alarm beeps twice to DC
start the UPS and power the load.
OFF BUTTON: When the UPS is in the AC normal mode; Press
and then release the OFF button after the audible alarm beeps
twice to turn the UPS off. The UPS will continue to charge the
batteries whenever it is plugged into a wall outlet and there is ac-
ceptableACvoltagepresent.
CAUTION! To de-energize the outputs of the UPS:
1. If the UPS is on press and then release the OFF button after the audible
alarm beeps twice to turn the UPS off.
2. Disconnect the UPS from theAC wall outlet.
3. To de-energize the UPS completely, disconnect the battery.
Life Support Policy
As a general policy, we do not recommend the use of any of our products in
life support applications where failure or malfunction of the product can be
reasonably expected to cause failure of the life support device or to signifi-
cantly affect its safety or effectiveness. We do not recommend the use of any
of our products in direct patient care. We will not knowingly sell our products
for use in such applications unless it receives in writing assurances satisfac-
tory to us that (a) the risks of injury or damage have been minimized, (b) the
customer assumes all such risks, and (c) our liability is adequately protected
under the circumstances.
Receiving Inspection
After removing your UPS from its carton, it should be inspected for damage
that may have occurred in shipping. Immediately notify the carrier and place
of purchase if any damage is found. Warranty claims for damage caused by
the carrier will not be honored. The packing materials that your UPS was
shipped in are carefully designed to minimize any shipping damage. In the
unlikely case that the UPS needs to be returned to the manufacturer, please
use the original packing material. Since the manufacturer is not responsible
for shipping damage incurred when the system is returned, the original pack-
ingmaterialisinexpensive insurance. PLEASE SAVE THE PACKING MATE-
RIALS!
© COPYRIGHT 2017 BY PARASYSTEMS, INC.
All Rights Reserved.All rights of this User's Manual (“Manual”), including but
not limited to the content, information, and figures are solely owned and re-
served by Para Systems, Inc. (“Para Systems”). The Manual can only be
applied to the operation or the use of this product. Any disposition, duplica-
tion, dissemination, reproduction, modification, translation, extraction, or us-
age of this Manual in whole or in part is prohibited without the prior written
permission of Para Systems. Given that Para Systems will continuously im-
prove and develop the product, changes may be made to the information in
thisManualatanytimewithoutobligationtonotifyanyperson of such revision
or changes. Para Systems will make all possible efforts to secure the accu-
racy and the integrity of this Manual. Para Systems disclaims any kinds or
forms of warranty, guarantee, or undertaking, either expressly or implicitly,
including but not limited to the completeness, faultlessness, accuracy, non-
infringement,merchantabilityorfitnessforaparticularpurposeoftheManual.

7
6
NOTE: The LCD backlight will illuminate for 20-seconds when the UPS is con-
nectedto utilitypower,whentheUPS isturned ON/OFF, whenany ofthe buttonson
theLCD panelare touchedand whenthe UPSswitches tothe Batterymode. When
the UPS has an event and/or an error code the LCD backlight will turn on and re-
mainon to alert theuser that an eventhas occurred.
Chapter 2: Controls and Indicators
1. The ON button is to turn the UPS on. Pressing the ON button during the
Batterymodewillsilence the alarm.
2. The OFF button is to turn the UPS off.
3. The Utility Power (Green) LED illuminates when Utility Power is present
andextinguishesduring the Battery mode.
4. The Load Bank 1 (Green) LED is illuminated when the Load Bank is on.
5. The Load Bank 2 (Green) LED is illuminated when the Load Bank is on.
6. The BypassActive(Yellow) LED illuminates when the UPS is in the Bypass
mode.
7. The Weak/Bad Battery (Red) LED illuminates when the UPS detects a weak
battery, bad battery or if the battery is disconnected. The Weak/Bad Battery
iconis extinguished when the battery's conditionis good.
8. The LCD displays the status of the UPS.
9. Pressing the Enter button saves the changes made to the UPS settings.
10.Pressing the Page Up button goes to the previous page or will change the
UPSsettings.
11.Pressing the Page Down button goes to the next page.
12.PressingtheFunctionbuttonandthenthePageUpbuttonwillinitiatea10-
secondbatterytest.
1. Displays the power flow of the UPS:
The UPS reports the following parameters on the LCD screen:
Input: Voltage,Frequency
Output: Voltage,Frequency, Current,Percentage of load
Battery: Voltage
Runtime: Thetime operating on the Batterymode in minutes
Temperature: The internal temperature of the UPS in degress C
2. TheSite Wiring Faulticon illuminates when theUPS detects a sitewiring prob-
lem. The SWF icon is extinguished when the UPS is connected to properly
wiredwall outlet.
3. TheAlarmSilencericon illuminates whenthe audible alarmhas been silenced.
4. TheOverload icon willilluminate when the amountof load attachedtothe UPS
is >106% of its power rating.
5. TheService icon illuminateswhen the UPS requires service.
6. TheAlarm(Fault)icon illuminates whenthe UPS detectsan internalfault.
7. Numerical values of the UPS parameters and error codes.
ACModePowerFlow
BatteryModePowerFlow
BypassModePowerFlow

9
8
INSTALLATION PLACEMENT
This UPS series is ONLYintended to be installed in an indoor temperature con-
trolled environment that is free of conductive contaminants. DO NOT operate the
UPSin: extremely dustyand/or uncleanareas, locations nearheating devices, wa-
teror excessive humidity, orwhere the UPS isexposed to direct sunlight. Selecta
location, which will provide good air circulation for the UPS at all times. Route
power cords so they cannot be walked on or damaged. This UPS series is not
intendedfor usein a computerroom asdefined in theStandard forthe Protection of
ElectronicComputer/Data Processing EquipmentANSI/NFPA75. Typical battery
lifeis 3 to5 years. Environmental factors doaffect battery life. Hightemperatures,
poorutility power,and frequent,short duration discharges have anegative impact
onbattery life.
Operating Temperature (Maximum): 0 to 40°C (+32 to +104°F)
Operating Elevation: 0 to 3,000m (0 to +10,000 ft)
Operatingand StorageRelative Humidity: 10%to 90%, non-condensing
Storage Temperature: -15 to +45°C (+5 to +113°F)
Storage Elevation: 0 to 15,000m (0 to +50,000 ft)
REAR PANEL
1. The USB Communications Port is for UPS monitoring and control.
2. The RS232 Communications Port is for UPS monitoring and control.
3. The EPO (Emergency Power Off) Port is for UPS control.
4. TheR-J11/R-J45modular connectors areusedfor 10/100/1000 Base-T Netw-
ork/singleline Phone/Fax/Modem protection.
5. Theinput power cordis for connecting to utilitypower.
6. The option slot is for option cords.
7. TheBatteryBackup output receptacles. Theoutput receptacles areelectrically
wiredinto two segmentsto support the"Load Shedding Function"(Labeled1 &
2). The 3KVA has a locking receptacle (Always On) that does not support the
"LoadShedding Function". NOTE: Thelocking receptacle isnot on allmodels.
8. Therackmount brackets.
9. Theinput circuitbreakerwill trip inthe event theload exceeds theUPS’s power
rating.
10.The fan isfor ventilation.
11. Theoutput circuitbreaker willtrip inthe eventthe loadexceeds theUPS’s power
rating. NOTE: The output circuit breaker is not on all models.
OutputPowerReceptacles
NEMA5-15P
Model#
EC1500RT2U
EC2000RT2U
EC1000RT2U
EC3000RT2U
NEMA5-15P
NEMA5-20P
NEMAL5-30P
6-NEMA5-15R(Controllable)
6-NEMA5-15R(Controllable)
6-NEMA5-15/20R(Controllable)
6-NEMA5-15/20R(Controllable)
1-NEMAL5-30R(AlwaysOn)
INSTALLATION
Besure to read theinstallationplacement and all thecautions before installing the
UPS. Place the UPS in the final desired location and complete the rest of the
installationprocedure. These UPSs areshipped with theinternal batteries discon-
nected. The batteries must be connected before putting these UPSs into service.
Seethe "Connectingthe Batteries" procedureto connect thebatteries andthen the
"Rackmount Configuration" to install the UPS into the rack. USE CAUTION: The
UPSis heavy. Use theappropriate number of personnel wheninstalling theUPS.
InputPowerPlug
(Allpowercordsare10ft)
CAUTION! DO NOT USE THE MOUNTING BRACKETS TO LIFT THE UPS.
The mounting brackets are ONLYfor securing the UPS to the rack.
Chapter 3: Installation

11
10
RACKMOUNT CONFIGURATION
ThisUPS series comes with mounting brackets for the standard 19" (46.5cm)
rack pre-installed on the UPS. There are optional Rail Kits for the 4-post
racks and cabinets available. The screws for mounting the UPS to the rack
are included. NOTE: The Rail Kit for a 4-post rack and/or cabinet is included
withthe EC3000RT2U.
CAUTION! DO NOT USE THE MOUNTING BRACKETS TO LIFT THE
UPS. The mounting brackets are ONLYfor securing the UPS to the rack.
1. Mount the UPS into the rack and secure with the retaining screws (provid-
ed). WARNING: Use two or more people when installing the UPS, the
UPS is extremely heavy. Do not move the rack after the units have been
installed. The rack may become unstable due to the weight distribution.
2. The Rackmount Configuration is complete. See Connecting your Equipm-
ent.
CONNECTING THE BATTERIES
(QUALIFIEDSERVICEPERSONNELONLY)
Please read all of the WARNINGS and CAUTIONS before attempting to con-
nectthebatteries.
WARNING: Use two or more people when installing the UPS, the UPS is
extremelyheavy.
1. Remove the UPS from the shipping box and place on a flat surface.
2. Grasp the battery door on the left hand side, pull it outward and then set it
aside (FIG. 1).
3. Press down to unlock the battery connector holder. Verify proper polarity.
Connect the battery connectors (red and black) together. Place the batt-
ery connectors in the battery connector holder and then relock the battery
connector holder (FIG. 2).
NOTE: Some sparking may occur this is normal.
4. Re-install the battery door on the UPS.
5. Connecting the Batteries is complete. See the Rackmount Configuration.
CAUTION! DO NOT USE THE MOUNTING BRACKETS TO LIFT THE
UPS. The mounting brackets are ONLYfor securing the UPS to the rack.
FIG. 1
FIG. 2

13
12
TOWER CONFIGURATION
The tower configuration allows the user to install the UPS in the up-right posi-
tion. The tower brackets are provided with the UPS. WARNING: Use two or
morepeoplewheninstallingthe UPS, the UPS is extremelyheavy.
1. Once the locationoftheUPShasbeendetermined,place the UPS on a flat
surface,removetherackmountbracketsfromtheUPSandthenattachthe
four (4) tower brakects as shown below.
2. Stand the UPS in the up-right position and place it in the desired location.
Make sure that the UPS is stable.
3. The LCD panel can be rotated to read in the up-right position. There are
twosmallslots,oneoneachsideoftheLCDpanel. Insertasmallflatscre-
wdriver into the slot to pop out the LCD panel. Position the LCD panel so
that it reads in the up-right position. Press the LCD panel back into the fr-
ontpanel.
WARNING: The UPS must be installed in the proper up-right position. If the
UPS is not installed in the proper up-right position the Batteries will be dam-
aged. OncetheUPSisplacedinthetowerbrackets,lookingat the front panel
theYELLOWBattery disconnected label on thetopcoverofthe UPS MUST be
on your left hand side.
4. The Tower Configuration is complete. See Connecting your Equipment.
CHARGING THE BATTERY
The UPS will charge the internal batteries whenever the UPS is connected to
an AC source and there is an acceptable AC voltage present (55V (load de-
pendent) - 150VAC). It is recommended that the UPS's batteries be charged
for a minimum of 4 hours before use. The UPS may be used immediately,
however,the “On-Battery”runtimemay be lessthannormally expected. NOTE:
If the UPS is going to be out of service or stored for a prolonged period of
time, the batteries must be recharged for at least twenty-four hours every
ninety days.
CHECKING THE SITE WIRING FAULT
Afterplugging the UPS into theAC wall outlet, check the Site Wiring Fault icon
on the front panel of the UPS. If the Site Wiring Fault icon is illuminated and
error code Er16 is displayed, the UPS is plugged into an improperly wiredAC
wall outlet. If the UPS indicates a Site Wiring Fault have a Qualified Electri-
cian correct the problem.
CONNECTING THE UPS TO AN AC SOURCE
PlugtheUPSintoa two pole, three wire, groundedACwalloutlet. TheACwall
outlet shall be near the UPS and shall be easily accessible. The plug on the
input power cord on this UPS series is intended to serve as a disconnect
device. DO NOT PLUG THE UPS INTO EXTENSION CORDS, ADAPTER
PLUGS OR SURGE STRIPS. DO NOT CUT THE INPUT PLUG OFF AND
ATTEMPT TO HARDWIRE THIS UPS, DOING SO WILL VOID THE WAR-
RANTY.
NETWORK/PHONE/FAX/MODEM PROTECTION CONNECTION (OP-
TIONAL)
Connecta10/100/1000Base-T network, single line phone, Fax or Modem line
to the RJ11/45 modular connectors on the rear panel of the UPS. This con-
nection will require another length of telephone or network cable. The cable
coming from the telephone service or networked system is connected to the
port marked “IN”. The equipment to be protected is connected to the port
marked"OUT". NOTE: Connectingto the Network/Phone/Fax/Modem modu-
lar connectors is optional. The UPS works properly without this connection.
CONNECTING YOUR EQUIPMENT
Plug the equipment into the output receptacles on the rear panel of the UPS.
Ensurethatyoudonotexceed the maximum output rating of the UPS (refer to
the information label or the Electrical Specifications in this manual). DO NOT
PLUG EXTENSION CORDS,ADAPTER PLUGS OR SURGE STRIPS INTO
THEOUTPUTRECEPTACLES OFTHEUPS.
CAUTION! DO NOT connect a laser printer to the output receptacles on the
UPS, unless the UPS is rated 2000VAor greater. Alaser printer draws signifi-
cantly more power when printing than at idle and may overload the UPS.

15
14
EMERGENCY POWER OFF (EPO) FUNCTION
Connect one end of a two (2) wire cable to the EPO port on the rear panel of
the UPS and the other end of the two (2) wire cable to an EPO switch. To
shutdown the UPS in the AC or the Battery mode short pin1 to pin2 for ap-
proximately 0.5-seconds. In the AC mode; the UPS must be turned off and
then back on again to restart the UPS. In the Battery mode; once the utility
power returns the UPS must be turned on to restart the UPS. The LCD will
display EPo for this function.
Chapter 4: Operation
The UPS will charge the batteries when the UPS is in the on or off position as
long as the UPS is plugged into the wall outlet and there is an acceptableAC
voltage present (55V (load dependent) - 150VAC). When a blackout, brown-
out, or an overvoltage condition occurs while the UPS is in the On-Line mode
or the Economy mode; the UPS will transfer to the battery mode, the On-
Battery indicator will illuminate and the audible alarm will sound once every
ten-secondsindicatingthattheutilitypowerislostor unacceptable. When the
utility power returns or is at an acceptable level, the UPS will automatically
transferbacktotheOn-Line mode or the Economy mode and start recharging
the batteries. During an extended outage when there is approximately two-
minutes of backup time remaining the audible alarm will sound twice every
five-seconds. This Low Battery Warning is letting the user know that they
should save all open files and turn off their equipment. When the batteries
reachthepredeterminedleveltheUPSwillautomatically shutdown protecting
the batteries from over discharging. Once the utility power returns the UPS
will automatically restart providing safe usable power to the connected equip-
ment and start recharging the batteries.
The Economy mode operation: The input utility power 'bypasses' the inverter
circuit and is connected directly to the output of the UPS powering the con-
nectedequipmentwhilesimultaneously charging the batteries. When a black-
out, brownout, or an overvoltage condition occurs the UPS will transfer to the
batterymode,the inverter will turn on powering the connected equipment, the
On-Batteryindicatorwill illuminate and the audible alarmwillsoundonceevery
ten-secondsindicatingthattheutilitypowerislostor unacceptable. When the
utility power returns or is at an acceptable level, the UPS will automatically
transfer back to the Economy mode and start recharging the batteries.
COMMUNICATIONS PORT CONNECTION (OPTIONAL)
The Power Monitoring Software and interface cables can be used with the
UPS. Use only the interface cables that come with these UPSs. Connect the
interface cable (Serial or USB) to the appropriate communications port on the
rear panel of the UPS. Connect the other end of the cable to the device that
will be monitoring/controlling the UPS. NOTE: Connecting to the Communi-
cations Port is optional. The UPS works properly without this connection.
OPTION SLOT (OPTIONAL)
The option slot on the rear panel of the UPS is for the SNMP and the Relay
cards. Removethecoverplatesfromtheoptionslot. Install the SNMP card or
the Relay card. Connect the appropriate interface cable to the SNMP card or
the Relay card on the rear panel of the UPS. Connect the other end of the
cable to the device that will be monitoring/controlling the UPS. NOTE: Using
the Option Slot optional. The UPS works properly without this connection.
SYSTEM OVERVIEW
This double conversion On-Line UPS protects computers, servers, telecom-
munications, security and other electronic equipment from blackouts, brown-
outs, overvoltages, and surges. This On-Line UPS converts the input AC to
DCandthen back to a true sine waveAC output. The true sine wave output is
regulated within 2% of the nominal output voltage. The Power Factor Correc-
tion (PFC) circuitry corrects the input power factor to within 99% of unity and
blocks the load generated harmonic distortion from getting back on the input
AC line. This On-Line UPS provides a continuous true sine wave output with
zero transfer time and great regulation to protect your mission critical equip-
ment. The UPS will quietly and confidently protect your system from power
anomalies.
Block Diagram of the Basic Wiring and Internal Circuit Configuration

17
16
COMMUNICATIONS PORTS (RS232and USB)
The RS232 communication port is a standard DB9 female. The pinout for the
port is below:
Pin 2: /TXD
Pin 3: /RXD
Pin 5: Ground
TheUSBprotocolisHID. The HID USB driver is the standard for the Windows
OS. SimplyplugtheUSBcableintothe UPS and the computer then follow the
prompts on the screen. NOTE: When using the UPS's USB port with
Windows XP, 7,8 or 10 the Power Options in the Control Panel may need
to be configured.LOAD SHEDDING FUNCTION
Theoutput receptaclesare electricallywired intotwo segmentsto supportthe "Load
Shedding Function" (Labeled 1 & 2). The user can control the two segments indi-
vidually or both at the same time. The Load Shedding Function is controllable by
thePower Monitoring Software or theSNMP card. NOTE: The locking receptacle
(AlwaysOn) does not support the"Load Shedding Function".
TURNING THE UNIT ON/OFF
Turning the unit On
When the UPS is connected to anAC source and there is an accept-
ableAC voltage present; Press and then release the ON button after
theaudible alarm beepstwice to turnthe UPS Onand power theload.
DC START:Press and then release the ON button after the audible
alarm beeps twice. Then within 10-seconds press and then release
theON button afterthe audible alarmbeeps twice toDC start theUPS
andpower the load.
Turning the unit Off
When the UPS is in theAC normal mode; Press and then release the
OFF button after the audible alarm beeps twice to turn the UPS Off.
The UPS will continue to charge the batteries whenever it is plugged
into a wall outlet and there is acceptableAC voltage present.
EMERGENCY POWER OFF (EPO) FUNCTION
Connect one end of a two (2) wire cable to the EPO port on the rear panel of
the UPS and the other end of the two (2) wire cable to an EPO switch. To
shutdown the UPS in the AC or the Battery mode short pin1 to pin2 for ap-
proximately 0.5-seconds. In the AC mode; the UPS must be turned off and
then back on again to restart the UPS. In the Battery mode; once the utility
power returns the UPS must be turned on to restart the UPS. The LCD will
display EPo for this function.
ECONOMY MODE (ECO) FUNCTION
The UPS must be turned on and in the normal AC mode. The Economy mode
optionmust be Enabledthrough the SNMPcard or thePower Monitoring software.
Once the Economy mode has been Enabled the LCD will display ECO and the
Bypass(Yellow) LED will beilluminate. Turnon the connectedequipment one ata
time.
OPTION SLOT
The option slot on the rear panel of the UPS is for option cards. Contact your
local dealer or visit our Web site at www.minutemanups.com for the available
option cards for this series.
POWER MONITORING SOFTWARE
The UPS comes with a Power Monitoring Software CD or you can go to our
website at www.minutemanups.com/support,thenlookunder Downloads, and
thenSoftwareDownload Center. Pleasedownload(FreeofCharge)thelatest
version of the Minuteman SentryHD software. See the software CD for the
installationofthePowerMonitoringSoftware.
USER INVOKED BATTERYTEST
Theuser invoked battery testfeatureis useful to verifythe correct operation ofthe
UPS and the condition of the batteries. With the UPS in the AC normal mode;
Press the Function button and then the Page Up button. The UPS will perform a
ten-secondbattery testto measurethe battery’scapability tosupport theconnected
load. During the battery test, the UPS will switch to the battery mode, the Battery
modepower flow willilluminate and the audiblealarm will sound. Ifthe UPS fails a
battery test, one of the icons and/or error codes will remain illuminated indicating
thetype of problem.
ALARM SILENCER
Whenthe UPS is operatingin the Battery modepress the ON button tosilence the
audible alarm. Once the UPS reaches the Low Battery Warning (LBW) threshold
theaudible alarm willstart beepingagain. Whenthe UPS returnsto the normalAC
modethe audible alarm willreset to default. Theaudible alarm cannot besilenced
duringthe LBW orany Fault/error event.
CHANGING THE OUTPUT VOLTAGE
The output voltage can to configured for 110V, 120V, or 127V. The default
setting for the output voltage is 120V. To change the output voltage follow the
stepsbelow:
1. Connect the UPS to utility power. DO NOT turn on the UPS.
2. Press theONbutton and the PageDownbuttonsimultaneously until theau-
dible alarm beeps once and then release.
3. Use thePageUp button toselectthe desired outputvoltagesetting and then
press the Enter button to save the changes.
4. Pressthe ON button to turn on the UPS and verify the output voltage. Cha-
ngingthe output voltage is complete. The UPS is ready for normal operat-
ion.

19
18
WEAK/BAD/DISCONNECTED BATTERY
TheUPSautomaticallytests the battery’s condition. If the battery is weak, bad
or disconnected, the Weak/Bad/Disconnected Battery icon will illuminate, er-
ror code Er15 will be displayed and the audible alarm will beep three times
every five-minutes until the battery is reconnected, replaced or passes a self
test. It is recommended that the UPS be allowed to charge overnight before
performing a battery test to confirm a Weak/Bad Battery condition. NOTE:
The audible alarm cannot be silenced during this condition.
OVERLOAD
When the amount of load attached to the UPS is > 106% of its power rating;
the Overload icon will illuminate, the error code Er02 will be displayed and the
audiblealarmwill beep continuously. Thisalarmwillremainon until the excess
loadisremovedortheUPS’sselfprotectioncircuitshutstheUPSdown. Ifthe
UPSshutsdownbecauseof an Overload condition, the UPS must perform an
Inverter function or a Self Test to clear the Overload Alarm. NOTE: The
audible alarm cannot be silenced during this condition.
ALARMS
ON BATTERY
When the UPS is operating on the batteries, the On-Battery icon will illumi-
nate, the Utility power LED (Green) will extinguish and the audible alarm will
sound one beep every ten-seconds. The audible alarm can be silenced dur-
ing this condition. The alarm will stop once the UPS returns to theAC normal
mode.
LOW BATTERYWARNING
WhentheUPS is operating on the batteries and the battery reserve is running
low,theaudiblealarmwillsoundtwobeepsevery five-seconds and error code
Er17willbedisplayed. ThisconditionwillcontinueuntilAC returns or the UPS
shuts down from battery exhaustion. NOTE: The audible alarm cannot be
silenced during this condition.
UPS FAULT
When the UPS detects a hardware and/or internal fault, the Fault icon will
illuminateandtheaudible alarm will beep continuously. Thefault condition, in
some instances, may be reset by turning the UPS off and then on again.
NOTE: The audible alarm cannot be silenced during this condition.
(These items may require optional software or hardware)
Function Factory
Default Description
User Choices
Set
inverter
output
voltage
Shut-
down
Type
Set
audible
alarm
state
Enable/
Disable
auto
restart
Battery
replace
date
Battery
install
date
Date of
manufac-
ture
5yearsfrom
the install
date
Enabled
Enabled
EntireUPS
120VAC
Date of battery
replacement-
month/day/year
XX/XX/XXXX
Dateofthenext
battery re-
placement-
month/day/year
XX/XX/XXXX
Enable
or
Disable
Enabled,at
lowbattery,
disabled
Entire UPS or
UPSoutput
110, 120,
127VAC
Enter the date of the next battery
replacement.
Enterthe current date when
replacingbatteries.
Changesthe output voltage.
Enabled-theUPSwillemitashort
beep when in the battery mode.
AtLowBattery theUPSwill emit
twobeeps from low batterywarn-
inguntilshutdown.
Disabled - Use only when soft-
ware is controlling the UPS or to
silencethealarm.
When enabled, the UPS will
automatically restart from a low
batteryshutdownwhennormalAC
returns.
Enable/
Disable
ECO
Disabled Enable
or
Disable
Enabled- the UPS will operate in
theEconomy mode.
EntireUPS-Turnsofftheentire UPS.
UPS Output - Turns off the UPS's
outputreceptaclesonly.
Chapter 5: Configurable Parameters
and Settings
Enable/
Disable
Load
Shed-
ding
Disabled Enable,
Disable or
Configure
Enabled - the specified outlet
bank will turn off.
Configure - the specified outlet
bank will turn on or off based on
theselected event.
SITE WIRING FAULT
If the Site Wiring Fault icon is illuminated and error code Er16 is displayed,
the UPS is plugged into an improperly wired AC wall outlet. If the UPS indi-
cates a Site Wiring Fault have a Qualified Electrician correct the problem.

21
20
Chapter 6: Obtaining Service
IF THE UPS REQUIRES SERVICE
1. Use theTroubleshootingsection to eliminate obvious causes.
2. Verify there are no tripped circuit breakers and that the batteries are good.
A tripped circuit breaker and defective batteries are the most common iss-
ues.
3. Call your dealer for assistance. If you cannot reach your dealer, or if they
cannotresolvethe issue call or fax theTechnical Support departmentat the
following numbers; Voice phone [phone], FAX line [phone]
or visit our Web site at www.minutemanups.com the "Discussion Board".
Before calling the Technical Support Department have the following infor-
mationavailable:
a) Contact name and address.
b) Where and when the unit was purchased.
c) All of the model information about your unit.
d) The serial number of your unit.
e) Any information on the failure, including LEDs that may be illuminated
or error codes displayed.
f) A description of the protected equipment including model numbers, if
possible.
g) A technician will ask you for the above information and if possible,
helpsolvetheissue over the phone. In the event that the unit requires
factoryservice,theTechnical Support Representative will issue you a
Return MaterialAuthorization Number (RMA#). NOTE: We must
have the model number and the serial number of the product to
issue an RMA #.
h) If the unit is under warranty, the repairs will be done at no charge. If
the unit is not under warranty there will be a charge for the repair.
4. Pack the unit in its original packaging. If the original packaging is no lon-
geravailable,asktheTechnicalSupport Representativeaboutobtaininga
new set. It is important to pack the unit properly in order to avoid damage
in transit. Never use Styrofoam beads for a packing material.
a) Include a letter with your name, address, day time phone number,
RMAnumber, a copy of your original sales receipt, and a brief desc-
ription of the problem.
5. MarktheRMA# on the outside of all packages. The factory cannot accept
any package without the RMA # marked on the outside of the package.
6. Return the unit by insured, prepaid carrier to:
Para Systems Inc.
MINUTEMANUPS
1809 W. Frankford Road, Suite 150
Carrollton,TX75007
ATTN:RMA# _______
Er01: UPS is shutdown.
Symptom / Error Code Cause / What To Do
The UPS has not been turned on. Press the On button and re-
leaseaftertheaudiblealarmbeeps twice.
Only the AC normal LED is
illuminated. Reset the input circuit breaker by pressing the plunger back in. If
the input circuit breaker trips after UPS restarts, reduce the load
on the UPS.
UPSonlyoperates in battery
mode, even though there is
ACpresent.
The AC normal icon is illumi-
nated, but there is no output. Disconnect the computer cable from the UPS, press the On but-
ton. If UPS works normally, the software has control of the UPS.
Charge the batteries for 8-hours and retest. If the runtime is still
less than expected, the batteries may need to be replaced.
UPSdoesnot provide the
expectedruntime.
TheUPShas an internal problem. Call for service.
The Fault icon is illuminated
and a constant alarm.
Er02: TheOverload icon is il-
luminated and a constant
alarm.
Check the specifications and remove part of the load. If the UPS
shuts down because of an Overload, the UPS must perform an
Inverter function or a Self Test to clear the Overload Alarm.
The UPS has detected a short-circuit on its output. Check the at-
tachedload.
Er03: UPSOverTemperature. The internal temperature has exceeded the safe operating range
for the UPS. Check the specifications.
Er08: DCBUS voltageabnor-
mal(High). Turn the UPS off, unplug the power cord, wait for 5-minutes and then restart the UPS. If the error did not clear call for service.
Er11: Inverter/OutputFailure
Shutdown. TheUPShasaninternal fault. Call for service.
Er13: Fan Failure. The fan haseither failedorhas stopped due to exessive dirt.Ifthe
fanhas failed,call forservice. Ifthe fanisdirty,use acan of"Canned
Air" to clean the fan.
Er14: ChargerFailure. Thechargerhas failed, call for service.
Er16: Site Wiring Fault. Haveaqualified electrician correct the service wiring.
Er15: Weak/BadBattery icon
is illuminated. Checkthebatteryconnections,charge the batteries for 8-hours
and retest. The batteries may need to be replaced.
Er17: Low Battery Warning. The UPS's battery reserve is low. Thiscondition will continue until
AC returns or the UPS shuts down from battery exhaustion.
Er26: InputOver Current.
Er09: DCBUS voltageabnor-
mal(Low). Turn the UPS off, unplug the power cord, wait for 5-minutes and
then restart the UPS. If the error did not clear call for service.
Er10: InverterOver Current. Check the specifications and remove part of the load.
Check the specifications and remove part of the load. If the error
did not clear call for service.
Chapter 7: Troubleshooting
Er28: BypassmodeOverload.
Er29: Charger overcharges
the battery. TheUPShasaninternal fault. Call for service.
Check the specifications and remove part of the load. If the error
did not clear call for service.
Er38: Failed to synchronize
with utility input. Turn the UPS off, unplug the power cord, wait for 5-minutes and
then restart the UPS. If the error did not clear call for service.
Er39: Low Battery Capacity. The UPS's battery capacity is low. Charge the batteries for 24-
hours. If the error does not clear call for service.
Er12: DCBUSPre-charge ab-
normal. Turn the UPS off, unplug the power cord, wait for 5-minutes and
then restart the UPS. If the error did not clear call for service.
Er18: EEPROM data error. TurntheUPS off, unplugthepower cord, waitfor1-minute and then
restart the UPS. If the error does not clear call for service.

23
22
BATTERYREPLACEMENT PROCEDURE
PLEASE READ THE CAUTIONS AND WARNINGS BEFORE ATTEMPTING
TOREPLACETHE BATTERYMODULE
Hot-swappablebatteriesmeanthatthebatterymodulescanbereplacedwith-
outpowering down the whole UPS system.
NOTE: If there is a power interruption while replacing the hot-swappable bat-
terymodule, with the UPS on, theload will not be backed up. To hot-swap the
batterymodulestartwith step number 6.
1. Turn off the equipment that is plugged into the output receptacles of the
UPS.
2. Press and release the OFF button on the front panel to turn the UPS Off.
3. Unplug the UPS'sAC power cord from the AC wall outlet.
4. Unplug the equipment from the output receptacles of the UPS.
5. Unplug the computer interface cable from the rear panel of the UPS.
6. Grasp the battery door on the left hand side, pull it outward and then set it
aside (FIG. 1).
7. Press down to unlock the battery connector holder. Disconnect the Battery
connectors (red and black). (FIG. 2)
8. Remove the two retaining screws for the battery retaining bracket. (FIG. 2)
9. Remove the battery retaining bracket.
EC1000RT2U EC2000RT2U
Internal
Battery
Module
Part# BM0069
EC3000RT2U
BM0071
Model# EC1500RT2U
BM0070
Chapter 8: Replacing the Battery
WARNING! This UPS contains potentially hazardous voltages. Do not at-
tempt to disassemble the UPS beyond the battery replacement procedure.
This UPS contains no user serviceable parts. Repairs and battery replace-
ment must be performed by QUALIFIED SERVICE PERSONNEL ONLY.
CAUTION: Donotopenormutilatebatteries. Released electrolyte is harmful
to the skin and eyes and may be toxic.
QUALIFIED SERVICE PERSONNEL ONLY
CAUTION: Do not dispose of batteries in a fire. The batteries may explode.
The batteries in this UPS are recyclable. Dispose of the batteries properly.
The batteries contain lead and pose a hazard to the environment and human
health if not disposed of properly. Refer to local codes for proper disposal
requirements or return the battery to the supplier.
CAUTION: The battery system can present a risk of electrical shock. These
batteries produce sufficient current to burn wire or tools very rapidly, produc-
ingmoltenmetal. Observetheseprecautions when replacing the batteries:
1. Remove watches, rings, or other metal objects.
2. Use handtoolswithinsulatedhandles.
3. Wear protective eye gear (goggles), rubber gloves and boots.
4. Do not lay tools or other metal parts on top of batteries.
5. Disconnect the charging source prior to connecting or disconnecting the
batteryterminals.
6. Determineif the battery is inadvertently grounded. If the battery is, remove
the source of the grounding. Contact with any part of a grounded battery
can result in an electrical shock. The likelihood of such shock will be redu-
ced, if such grounds are removed during installation and maintenance.
Please read all of the WARNINGS and CAUTIONS before attempting to ser-
vice the batteries. Typical battery life is 3 to 5 years. Environmental factors
do affect battery life. High temperatures, poor utility power, and frequent,
short duration discharges have a negative impact on battery life.
CAUTION: Replace batteries with the same number and type as originally
installed in the UPS. These batteries have pressure operated vents. These
UPSscontainsealednon-spillablemaintenance-freelead acid batteries.
FIG. 1
FIG. 2
BM0070

25
24
10.Graspthebatterypulltabandgentlypullthebattery module out of the UPS
and set it aside. (FIG. 3)
NOTE: Use Caution, the battery module is heavy.
11.Slide the new battery module into the UPS.
12.Re-installthebatteryretaining bracket.
13.Re-install the two retaining screws for the battery retaining bracket.
14.Verify proper polarity. Reconnect the battery connectors (red and black).
(FIG. 4)
NOTE: Some sparking may occur this is normal.
15.Place the battery connectors in the holder and then lock in place. (FIG. 4)
16.Re-install the battery door on the UPS.
17.The UPS is now ready for the normal operation.
18.Properly dispose of the old battery module at an appropriate recycling fac-
ility or return them to the supplier in the packing material that the new batt-
ery module came in.
NOTE: If the UPS has a Weak/Bad BatteryAlarm after replacing the battery
module, the user must initiate a battery test to clear the Weak/Bad Battery
Alarm. To initiateaselftest see section 4 "USER INVOKED BATTERYTEST".
FIG. 3
FIG. 4
120VAC(110, 127VAC)
1500VA
1350W
1000VA
900W
Protection
WaveformType
Over-Current, Short-Circuit Protected and Latching Shutdown
TrueSine Wave
Frequency 50/60Hz, +/-0.2Hz (unless synchronized to utility)
NominalVoltage(Adjustable)
MaximumPowerCapacity
0 ms Typical
>90%(FullLoad)
ResettableCircuitBreaker
50 or 60 Hz, +/-6Hz, autosensing
0-160VAC
55V(loaddependent) - 150VAC
Nominal+/-2%
TransferTime
Efficiency(Line Mode)
InputProtection
FrequencyLimits
VoltageRegulation
AcceptableInput voltage
EC1000RT2U EC1500RT2U
ModelNumber
SYSTEMSPECIFICATIONS
Voltage Range
Topology DoubleConversionOn-Line, TrueSineWave
OUTPUT NON-BATTERY OPERATION
INPUT
Numberof Phase Single (1∅2W +G)
NominalVoltage 120VAC
LowVoltage TransferPoint 55V (load dependent) resets to Utility Power at 75V or higher
HighVoltageTransferPoint 150V resets to Utility Power at 145V or lower
FrequencyRange 60Hz: 54 - 66Hz or 50Hz: 44 - 56Hz
OUTPUT BATTERY OPERATION
VoltageRegulation Nominal +/-2% (until Low Battery Warning)
VoltageT.H.D. <3%(Full Linear Load)
+/-5% @ 100% Load change in 30 ms
DynamicResponse
SlewRate <1Hz / second
OverloadCapacity >106 to <110% for 2-mins;AC mode: Transfer to Bypass, DC Mode: Shutdown
>111 to <125% for 1-min; AC mode: Transfer to Bypass, DC Mode: Shutdown
>126 to <150% for 30-secs; AC mode:Transfer to Bypass, DC Mode: Shutdown
>151% Immediately;AC mode: Transfer to Bypass, DC Mode: Shutdown
EC2000RT2U EC3000RT2U
2000VA
1800W 3000VA
2700W
Chapter 9: Specifications
Switches from Bypass to Inverter +/-10% Of the rated input voltage
Switches from Inverter to Bypass
ECONOMY MODE OPERATION
Transfer Time 8 ms Typical
Resets 5VAC from Switch Point
PowerFactor Correction >99% at Full Load
CrestFactor 3 : 1

27
26
BATTERYSYSTEM
Typical RechargeTime
Typical Battery Life
BatteryModule 3-5 years, depending on discharge cycles and ambient temp
BM0069
8-hoursto90% after full load discharge
BatteryType Sealed,Non-Spillable,MaintenanceFree,ValueRegulatedLeadAcid
Runtime:FullLoad (minutes)
Runtime:Half Load (minutes) 10
10 3
2
SURGE PROTECTIONAND FILTERING
Audible Noise at 1 m (3 ft.)
10/100/1000 Base-T surge protec-
tion let-through (as a percentage
of an applied +/-2 kV 1.2/50 us,
500 a 8/20 uS test)
Telephone line surge protection
let-through (as a percentage of an
applied +/-2 kV 1.2/50 us, 500a 8/
20 uS test)
NoiseFilter
Surgevoltage let-through(as a
percentage of an applied +/-2
kV)
SurgeResponse Time
SurgeCurrent Capability
SurgeEnergy Rating 254 Joules
0 ns (instantaneous) normal mode; <5 ns common mode
<5%
normalandcommon mode EMI/RFI suppression
<55 dBA
<1%
<5%
6500Amps total
ENVIRONMENTAL
OperatingTemperature (max)
Operating/Storage Humidity
OperatingElevation
0to 40°C (+32 to +104°F)
10%to 90% Non-Condensing
0 to 3,000m (0 to +10,000 ft)
PHYSICAL
Weight - Net
Size - Net L X W X H
(rackmountbracketsinstalled)
Size - Shipping
L X W X H
Weight-Shipping
16.0 x 18.9 x 3.5"
407x479x88mm
22.4 x 21.4 x 9.0"
570x544x228mm
REGULATORYCOMPLIANCE
SafetyandApprovals cTUVus (Conformsto UL17785th Edition& CSA22.2 no.107.3-14 /
R: 2014), FCC Class A, CE certified, Energy Star certified, RoHS2
(EUDirective 2011/65/EU)
StorageElevation 0 to 15,000m (0 to +50,000 ft)
StorageTemperature -10to +50°C (+14 to +122°F)
BM0070 BM0071
10
3
15
5
23.7 x 18.9 x 3.5"
602x479x88mm
30.9 x 23.2 x 9.0"
785x590x228mm
59.5 lbs
27.0 Kgs
65.7 lbs
29.8 Kgs
44.1 lbs
20.0 Kgs
49.6 lbs
22.5 Kgs
24.3 lbs
11.0 Kgs
29.5 lbs
13.4 Kgs
44.1 lbs
20.0 Kgs
49.6 lbs
22.5 Kgs
19.2 x 18.9 x 3.5"
487 x 479 x 88mm
25.6 x 21.4 x 9.0"
650 x 544 x 228mm
ParaSystems, Inc. (ParaSystems)warrants thisequipment,when properly appliedand
operated within specified conditions, against faulty materials or workmanship for a pe-
riod of three years from the date of purchase. For equipment sites within the United
StatesandCanada, this warrantycoversdepot repair or replacementofdefective equip-
mentat the discretionofPara Systems. Depotrepairwill be fromthe nearest authorized
service center. The customer pays for shipping the product to Para Systems. Para
Systems pays ground freight to ship the product back to the customer. Replacement
partsand warranty laborwill be borneby Para Systems. Forequipment locatedoutside
ofthe United StatesandCanada, Para Systemsonly coversfaulty parts. ParaSystems
products that are depot repaired or replaced pursuant to this warranty shall only be
warrantedforthe unexpiredportionof the warrantyapplying to theoriginalproduct. This
warranty applies only to the original purchaser who must have properly registered the
productwithin 10days ofpurchase.
Thewarranty shallbe voidif (a) the equipment is damaged by the customer,isimprop-
erlyused, issubjected toan adverseoperating environment, or is operated outside the
limitsof its electricalspecifications; (b)the equipment isrepaired ormodified by anyone
otherthan Para Systems or ParaSystems approvedpersonnel; or (c)has beenused in
amanner contraryto theproduct’s User'sManual orother writteninstructions.
Anytechnical advicefurnished beforeor afterdelivery inregard to use or application of
ParaSystems’ equipment isfurnishedwithout chargeandon the basisthat it represents
Para Systems’ best judgment under the circumstances, but it is used at the recipient’s
solerisk.
EXCEPTAS PROVIDED HEREIN, PARASYSTEMS MAKES NO WARRANTIES,EX-
PRESSEDORIMPLIED, INCLUDING WARRANTIESOFMERCHANTABILITYANDFIT-
NESSFORAPARTICULAR PURPOSE. Some statesdonotpermit limitation of implied
warranties;therefore, theaforesaid limitation(s) may not apply tothe purchaser.
EXCEPTAS PROVIDED ABOVE, IN NO EVENT WILL PARASYSTEMS BE LIABLE
FORDIRECT,INDIRECT, SPECIAL, INCIDENTAL,ORCONSEQUENTIALDAMAGES
ARISINGOUTOFTHEUSEOFTHIS PRODUCT, EVENIFADVISED OFTHEPOSSI-
BILITYOFSUCHDAMAGE. Specifically,ParaSystems is notliable for anycosts,such
as; labor for on-site installation, on-site maintenance or on-site service, lost profits or
revenue,loss of equipment,loss of useof equipment, lossof software, lossof data, cost
ofsubstitutes, claims by third parties, or otherwise. Thesole andexclusive remedy for
breachof anywarranty, expressed or implied, concerning Para Systems’products and
theonly obligation of Para Systems hereunder, shall be depot repairor replacement of
defective equipment, components, or parts; or, at Para Systems’ option, refund of the
purchase price or substitution with an equivalent replacement product. This warranty
givesyou specificlegal rights and you may also haveother rightswhich varyfrom state
tostate.
No employee, salesman, or agent of Para Systems is authorized to add to or vary the
terms of this warranty.
Chapter 10: Limited Product Warranty
140Joules

29
28
A1. DECLARATION OF CONFORMITY
Application of Council Directive(s): 2014/30/EU
Manufacturer’s Name: Para Systems, Inc. (MINUTEMAN UPS)
Manufacturer’sAddress: 1455 LeMayDrive
Carrollton,Texas 75007 USA
Type of Equipment: Uninterruptible Power Supplies (UPS)
ModelNo: EC1000RT2U(Y), EC1500RT2U (Y), EC2000RT2U (Y),
EC3000RT2U (Y)
I hereby declare that the equipment specified above conforms to the above
Directive(s).
Place:Carrollton,Texas, USA Date: July 10, 2017
RobertCalhoun
(Name) ManagerEngineering
(Position)
Year of Manufacture: Beginning July 2017
Standard(s) to which Conformity is declared: EN62040-2, IEC61000-2-2
IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-
6, IEC61000-4-8, UL1778, CSA22.2 no. 107.3-14, FCC Class A
Notes: