Minuteman C39085-01 Guide

390 Vacuum
Series
15, 30 & 55
Gallon Units
Stainless Steel
& Painted
Model No: C39085-01,02,03,04
C39105-01,02,03,04
C39130-01,02,03,04
C39330-01,02,03,04,05,06
C39055-01,02,03,04,05,06
Revised 7/02
OPERATION SERVICE PARTS CARE

1
FOR COMMERCIAL USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the
following:
READ ALL INSTRUCTIONS BEFORE USING
WARNING - To reduce the risk of fire, electric shock, or injury:
• Do not leave appliance when plugged in. Unplug from outlet when not in use and
before servicing.
• To avoid electrical shock, do not expose to rain, store indoors.
WARNING:
To reduce the risk of electrical shock - Do not use on wet surfaces. Do not expose to
rain. Store indoors.
• Do not allow to be used as a toy. Close attection is necessary when used by or near
children.
• Use only as described in this manual. Use only manufacturer’s recommended
attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has
been dropped, damaged, left outdoors, or dropped into water, return it to a service
center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run appliance over cord. Keep cord away
from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and
moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches,
or hot ashes.
• Do not use without dustbag and/or filters in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in
areas where they may be present.
• Connect to a properly grounded outlet only. See grounding instructions.
SAVE THESE INSTRUCTIONS

2
INSPECTION
Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly
inspected before shipment, and any damage is the responsibility of the delivery carrier who should
be notified immediately.
ELECTRICAL - 115 Volt
This machine is designed to operate on a standard 15 amp. 115 volt, 60 hz, AC circuit. Voltages
below 105 volts AC or above 125 volts AC could cause serious damage to the motor.
ELECTRICAL - 240 Volt
This machine is designed to operate on a standard 10 amp. 230 volt, 50 hz, AC circuit.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes
and ordinances.
DANGER
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with the appliance — if it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
This machine is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug
illustrated in Sketch A. Make sure that the machine is connected to an outlet having the same
configuration as the plug. No adapter should be used with this appliance.

3
WARNING
This vacuum may contain potentially hazardous dust depending on its appilcation. Special
handling of contaminated disposal bags and filters is recommended. Disposal must be in
compliance with local EPA regulations
USER MAINTENANCE INSTRUCTIONS
All service and repair should be performed by qualified vacuum service representative or electrician.
No user serviceable components are employed in the electrical vacuum lid head assembly. No
lubrication of the motor is required.
CLOTH BAG & HOSE ASSEMBLY
Cloth bag and hose assembly are user maintenance items and can be replaced when worn out. For
optimum performance, empty and clean filter bag regularly. A clogged and dirty bag restricts the
flow of air and results in reduced vacuum. The hose assembly can be maintained by wiping off with
a dampened cloth of mild liquid soap and water, then allowed to dry.
CORD STORAGE
While not in use storage can be accomplished by winding cord around motor lid assembly. Cord
should be completely unwound from lid assembly during operation.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return to service center.
• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around
sharp edges or corners. Do not run appliance over cord. Keep cord away from heated
surfaces.
• Do not unplug by pulling cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Always unplug the machine when removing the motor head off the tank.
This equipment should be stored indoors and not exposed to rain.
Always unplug the machine when removing the motor head off the tank. This equipment should be
stored indoors and not expposed to rain.

4
OPTIONAL INDUSTRIAL TOOLS AND ACCESSORIES
A
G
D
B
E
F
H
I
J
K
C
Part No. Description
800024 3” Rd Dust Brush Complete
800022 5” Rd Dust Brush Complete
800023 Bristle Insert 5”
800175MCH Dust Brush HSG 5”
800176MCH Dust Brush HSG 3”
800025 Bristle Insert 3”
800034 24” Crev Tool Aluminum Comp
800015 Wand Asy 1-1/2, Complete
800017 Set Tube, High-up 10’
800064 5’ Tube Lower Section
800019 5’ Section Upper
800116 Swivel, Hose End Exp, Comp
800317 Hose Asy 1-1/2 x 10’
800109 14” Squeegee, Comp
710330 SCR-SC 8-32 x .62
800121 14” Retaining Strip
800178PTD Casting, Tool MCH
800239 Blade Squeegee Wide
800240 Blade Squeegee Narrow
800038 6” Tool Squeegee, Complete
800029 Bristle Insert Replacement
800108 14” Fibre Tool Complete
710530 Screw 8/32 x 1/2 Brass
800003MCH Fibre Shod
800178PTD Tool Casting
800070 12” Gulper Tool, Comp
710356 SCR-MC 10-32 x .62
710357 SCR-MC 10-32 x .75
800187PTD Gulper Nozzle
800217 Fibre Shoe Rear
800218 Fibre Shoe Front
800032 6” Curved Pipe Tool, Comp
711006 Set Screw
800033 Bristle Insert Curved 6’
800193POL 6” Curved Pipe Tool

5

6
Item Part No Qty Description
1 760899 1 Handle Bail
2 760898PLT 1 Cap, Motor
3 760897PLT 1 Cover, Motor
4 760896 1 Shroud, Motor
5 760985PH 1 Pan, Motor
6 809754 1 Switch, Rocker
7 450088 1 Spacer, Switch
8 381020 1 Gray Cord Ste 16-3 50’
8A 740600 1 Cord HO5 VV-F3G1.5 x 50’
9 833237 1 Strain Relief
10 710355 2 SCR-MC 10-32 x .50 STPL
11 711553 2 WSR-Internal Lock #10
12 711310 2 Nut-Hex 10-32 x .50 STPL
13 712823 3 SCR-THMS 10-24 x 1.00 STPL
14 711126 6 SCR-ST-B 10 x .75 STPL
15 715105 1 Decal, P/V 105
15A 715085 1 Decal, P/V 85
15B 715130 1 Decal, P/V 130
16 715086 1 Decal, Warning
17 831478 1 Gasket, Neop 6 x 7.5 x .37
18 380064 1 Foam Ring
19 831484 1 Gasket, 3.5 x 4.5 x .31
20 380001 1 Vac Motor, Bypass 115V-85
20A 380054 1 Vac Motor, Bypass 240V-85
21 380028 2 Brush, Carbon-85
22 255039 1 Vac Motor, Bypass 115V-105
22A 255040 1 Vac Motor, Bypass 240V-105
23 255008 2 Brush, Carbon-105
24 831524 1 Vac Motor, Stage 3 115V-130
24A 831526 1 Vac Motor, Stage 3 240V-130
25 711124 1 SCR-ST-B 10 x .37
26 828995 2 Gasket, Neop 2.5 x 6 x .62
27 831626 1 Gasket 4 x 7.37 x .250
28 760213 1 Venturi Tube
29 712908 3 Nut-Flanged Wizz 10-24
30 831652 3 Spacer
31 290030 1 Lid Gasket
32 807051 1 Screen Filter SS 85/105
32A 832317 1 Screen Filter SS 130
33 830987 1 Float
34 833454 1 Float Cage
35 760260 1 Spring, Bag Retainer
36 760901 1 Lint Filter
37 712569 1 SCR-MC1/4-20 x 1.50 SS
38 711506 1 WSR-Flat 5/16 ST PL
39 712667 1 Nut-Hex 1/4-20 SS Nyloc
40 711505 2 WSR-Flat 1/4
41 711803 1 Cotter Pin
42 760904 1 Snub Bushing
43 715069 1 Decal, Check Filters
44 740088 1 Vac Light
45 740116 1 Ground Wire
46 760212 1 Vac Sensor Tube
Parts List

7

8
Parts List
Item Part No Qty Description
1 130032 2 Cap, Retainer
2 280016 2 Caster 3”
3 900112 1 Intake, MCH (750381-2 Only)
4 390087 1 Gasket Diecut
5 390110 1 Intake Assy Aluminum
6 711005 4 SCR-SK 1/4-20 x .31
7 711006 6 SCR-SK 1/4-20 x .62
8 711202 2 BLT-HH 1/4-20 x .50 STPL
9 711352 2 Nut-Acorn 1/4-20 ST NI
10 711503 8 WSR-Flat #10
11 711505 2 WSR-Flat 1/4
12 711524 2 WSR-Wave .52 x .87 x .01
13 711591 4 WSR-Rubber
14 711594 2 WSR-Flat .56 x .88 x .03 NI
15 711713 2 Retaining Ring Ext .50
16 711915 6 Rivet-Tube .19 x .28 NI PL
18 760984PTD 1 Bracket, Wheel
19 761054 2 Latch
20 900001PTD 1 Tank 15G Painted
20A 900003POL 1 Tank 15G Polished
21 900008 2 Wheel 8.00 DIA
22 900037PLT 1 Handle, Plated
23 900038 2 Clamp, Handle
24 900066 2 Axle
25 710530 1 SCR-MC 8-32 x .50 BR
26 711502 1 WSR-Flat #8
27 711372 1 Nut-Nloc 8-32 (750382 Only)
27A 711304 1 Nut-Hex 8-32 (750381-2 Only)
28 712824 2 SCR-THMS 10-24 x .75 STPL
29 500033 1 Locking Screw (750381-2 Only)
30 712638 2 Nut Hex 10/24 SS Nyloc
32 900035 1 Deflector, Intake
33 711542 1 Helical Washer #8
*** 390012 1 Molded Intake Complete
*** 390015 1 Molded Adapter 1 1/2
*** 390020 1 Molded Adapter 2.00
*** 750220 1 Tank Assy Comp 15gal PTD Asbestos
*** 750221 1 Tank Assy Comp 15gal SS Asbestos
*** 750322 1 Wheel Brkt Asy Comp
*** 750381 1 Tank Asy Comp PTD W/Deflector
*** 750382 1 Tank Asy Comp SS W/Deflector

9
Parts List
Item Part No Qty Description
1 760131 1 Molded Bag Ring
2 805054 1 Cloth Bag Only
3 805058 X Cloth Bag Asy Comp