
(BK<.3+46&3I5&?=,-&%+L5&
You!can!adjust!the!drop!size!using!the!app.!The!drop!
size!is!controlled!by!the!duration!of!the!valve!staying!
open.!If!you!want!to!see!bigger!drops,!then!you!need!
to!increase!the!time.!It!is!given!in!milliseconds.!If!you!
set! it! to! very! high! value! then! water! will! just! flow!
through!the!valve.!
!
If!you!don’t!want!to! send!the! second!drop,!you!can!
set!it!to!0!msec.!This!will!avoid!the!second!drop.!You!
can! add! a! delay! between! the! two! drops.! MIOPS!
Splash!will!send!the!second!drop!with!the!set!delay.!
You!can!also!add!a!delay!to!the!trigger!of!the!camera!
or! flash.! This! way! you!can! achieve! the! exact! photo!
you!want.!!
!
You! can! play! around! with! the! exposure! and! light!
settings! of! your! flash! and! camera! to! adjust! the!
shoot.!Below,!you!can!see!a!sample!setting!for!water!
drop!photography.!The!second!drop!will!hit!the!first!
one!after!it!bounces.!
!
8I246+46&3I5&E2335=9&
After!some!use,!you!may!need!to!replace!the!battery!
of!MIOPS!Splash.!The!battery!will!last!depending!on!
how!much!you!use!it.!It!is!easily!replaceable.!You!can!
only!use!a!23A!12V!alkaline!battery.!You!will!need!a!
Philips! screwdriver!to! change! the! battery.! You! can!
follow! these! steps! to! change! the! battery! of! the!
MIOPS!Splash.!
• Turn!the!MIOPS!Splash!off.
• Unplug!any!cables.
• Remove!the!screws!at!the!bottom!of!the!
device!with!a!Philips!screw!driver.
• Remove!the!old!battery.
• Put!a!compatible!battery!by!observing!the!
battery!polarity.
• Put!the!cover!back!on!and!tighten!the!
J+=*F2=5&M-6=2B5&
MIOPS!Splash!has!“Firmware!Upgrade!over!the!Air”!
capability.! In! other! words,! you! don’t! need! to! make!
any! cable! connection! to! complete! the! firmware!
upgrade.!You!can!follow!these!steps!to!complete!the!
firmware!upgrade!of!your!MIOPS!Splash.!
Open! the! MIOPS! Splash! app! and! go! to! the! Settings!
screen.!Select!Check!Firmware!Upgrade.!The!app!will!
connect! to! the! server! and! check! if! there! is! a!
firmware!upgrade!available!for!your!device.!If!a!new!
version!of!the!firmware!is!found,!the!app!will!notify!
you!with!a!pop-up!screen.!
If! you! want! to! upgrade! the! firmware,! touch! the!
“Upgrade”! button.! At! this! point,! the! MIOPS! Splash!
must! be! in! “Firmware! Upgrade”! mode.! In! order! to!
put! MIOPS! Splash! into! “Firmware! Upgrade”! mode,!
• If! it! is! turned! on,! turn! it! off!using! On-Off!
• Press!the!Valve!button!and!as!it!is!pressed!
turn!the!MIOPS!Splash!on.!
• The!Status!LED!will!glow!RED!continuosly.!
• Your!device!is!now!on!Firmware!Upgrade!
mode.!!
• The!app!will!discover!your!unit!and!it!will!
connect!to!it.!
!
You! can! complete! the! firmware! upgrade! by!
following!the!instructions!provided!by!the!app.!If!any!
error! occurs! during! the! firmware! upgrade! process,!
you! will! be! notified! with! related! information!
messages.!
N+-.&O&N=+07.&
The!most!preferred!way!of!taking!splash!pictures!is!
triggering! the! flash! while! the! camera! is! on! open!
shutter.! You! can! do! water! drop! photography! by!
triggering! your! camera! or! your!flash! and!MIOPS!
Splash!can!handle!both!of!them.!
Make!sure!that!you! set!an!appropriate!drop!size.!If!
you!keep!the!valve!open!too!long,!then!you!will!not!
get!a!drop.!
Make!sure!you!give!enough!delay!between!the!first!
and! second! drop.! This! will! help! to! create! the!
collision! effect,! where! the! second! drop! hits! the!
bouncing!first!one.!
If! you! trigger! the! flash! only,! pressing! the! shutter!
button!on!the!camera!may!cause!a!shake.!In!order!to!
avoid! that,! you! can! either! use! a! manual! remote! or!
the! better! way! is! connecting! the! camera! to! MIOPS!
Splash! as! well!(Optional! Camera! Triggering! cable! is!
required).! MIOPS! Splash! will! keep! the! shutter!open!
for! the! shoot.! The! camera! must! be! either! on! BULB!
mode! or! exposure! duration! long! enough! for! the!
drops!to!hit.!
You! can! get! a! full! version! of! the! user! manual! at!
www.miops.com.! For! all! kind! of! questions,! you! can!
send!an!email!to!info@miops.com.!