Mira L11 Operation manual

1
These instructions are to be left with the user
Installation & User Guide
SHOWER FITTINGS
MIRA L11

2
If you experience any difculty with the installation or operation of your new Shower
Fittings, please refer to ‘Fault Diagnosis’, before contacting Kohler Mira Ltd. Our
telephone and fax numbers can be found on the back cover of this guide.
CONTENTS
Introduction .............................................................................................3
Specications ..........................................................................................3
Pressures: ............................................................................................3
Flow Rates: ..........................................................................................3
Installation ...............................................................................................4
General .................................................................................................4
Install the Shower Fittings ....................................................................4
User Maintenance....................................................................................6
Cleaning ...............................................................................................6
Spare Parts ..............................................................................................7
Customer Service....................................................................Back Page

3
INTRODUCTION
SPECIFICATIONS
Pressures:
Minimum maintained pressure: 1 bar (100 kPa).
Maximum maintained pressure: 5.0 bar (500 kPa).
Warning! Exceeding the stated maximum maintained pressure could result in
excessive spray forces and possible damage to the handset.
Flow Rates:
Thank you for purchasing a quality Mira product. To enjoy the full potential of your
new product, please take time to read this guide thoroughly, having done so, keep
it handy for future reference.
Mira L11 Shower Fittings are precision engineered to give a satisfactory shower
over a range of pressures. The ttings are suitable for pressures between 1.0 and
5.0 bar.
This product comprises of an adjustable spray handset with three different spray
actions and is supplied complete with exible hose, adjustable clamp bracket
assembly, slide bar, hose retainer and supports. Suitable for connection to both
surface mounted and built-in shower controls.
0
5
10
15
20
25
0 0.5 1.0 1.5
Pressure (Bar)
Flow Rate (l/min)
Inner & Outer
Outer
Inner
2.0

4
INSTALLATION
General
1. Make sure that the shower ttings are installed by a competent installer.
2. Installations must comply with Water Regulations (Bye-Laws, Scotland), and
any other Local Regulations and Building Regulations in force at the time of
installation.
3. Before installation carefully inspect the new xture for any signs of damage.
4. The slide bar should be positioned to one side of the shower control at a
convenient height for all the family.
Install the Shower Fittings
Slide Bar
Slide Bar End
Slide Bar Ends
Slide Bar
Clamp Bracket
Assembly
Spirit Level
Fixing Hole
Fixing Hole
610 mm
Hose Retaining
Ring
1. If the clamp bracket assembly and the
hose retaining ring are not already
tted on the slide bar, then install
them before fitting the slide bar
ends.
2. Fit the slide bar ends into the slide
bar making sure that they are pushed
fully home.
3. Hold the slide bar assembly on the
wall in the required location and
make sure that it is level and upright.
Mark the positions of the top and
bottom xing holes.

5
Slide Bar
Washer
Wall Plug
Fixing Hole
Fixing Screw
Slide Bar End
Cover
Slide Bar
Handset
Clamp Bracket
Assembly
Hose
4. Drill the xing holes with an 8.0 mm
drill and t the wall plugs (supplied).
Caution! Make sure that you avoid
hidden cables and pipes when you
drill holes in the wall.
Note! Special consideration should
be given to the xing arrangements
when installing onto a dry lined,
stud partition or laminated panel
wall structure. Installers may wish to
obtain alternative proprietary cavity
fixings, or choose other options,
however, these methods of xings
are beyond the scope of this guide.
5. Hold the slide bar assembly on the
wall and secure in position at each
end with the washers and the screws
(supplied).
6. Fit the cover over each slide bar end
making sure that it locates correctly.
Caution! Do not overtighten the
hose.
7. Screw the hose onto the outlet of the
shower control making sure that the
hose washer is tted.
8. Pass the exible hose through the
hose retaining ring and screw the
remaining end of the hose onto the
handset making sure that the hose
washer is tted.
9. Place the handset in the clamp
bracket assembly.

6
USER MAINTENANCE
Cleaning
Warning! Many household cleaners contain abrasive and chemical substances,
and should not be used for cleaning plated or plastic ttings.
These nishes should be cleaned using a mild washing up detergent or soap solution,
rinsed and then wiped dry with a soft cloth.
Use your thumb or a soft cloth to wipe any limescale from the soft nozzles and the
front surface of the handset sprayplate.

7
SPARE PARTS
1630.034
Slide Bar
1630.035
Handset
1630.036
Clamp Bracket Assembly
1630.037
Hose Retaining Ring
1630.031
Hose
632.73
Hose Washer
A
A
A
A
B
B
B
B
1630.032 Slide Bar Support Assembly - components identied ‘A’
1630.033 Screw Pack - components identied ‘B’
The handset 1630.035 is
not available as of
24/3/2014 please use
2.1703.004
ref S West

8
CUSTOMER SERVICE
U
K
A
S
1065865-W2-B (L11) © Kohler Mira Limited, January 2007

Check out our full range of Showers
Electric Showers
Digital Showers
Mixer Showers
Power Showers
Smart Showers
Shower Towers
From Top Shower Brands
Mira Showers
Aqualisa Showers
Triton Showers
Gainsborough Showers
Shower Pumps can upgrade your showering experience even more
Stuart Turner Shower Pumps
Salamander Shower Pumps
Grundfos Shower Pumps