Mira Leap Walk In User manual

11245548-W2-A
Leap Walk In
These instructions must be left with the user
Installation Guide
A ICOHLER. COMPANY

2
1245548-W2-A

31245548-W2-A
Thank you for purchasing a quality Mira product. To enjoy the full potential of your new
product, please take time to read this guide thoroughly, having done so, keep it handy for
future reference.
The following pages aim to provide comprehensive installation instructions, plus advice on
how to care and maintain your product.
We recommend that the unit is installed by a qualied plumber or engineer.
Safety Information
1. Care should be taken when drilling into walls and oors to avoid any hidden pipes or
wires.
2. We strongly recommend that all glass panels are moved by a minimum of two people
and that any protective packaging along the glass edges is kept in place for as long as
possible to prevent damage before installation.
3. During installation we recommend additional help in lifting heavy doors and side panels.
4. Wear protective footwear when lifting panels.
5. Wear safety glasses when drilling.
GENERAL INFORMATION
INTRODUCTION
Before Fitting the Enclosure
1. Ensure the tray is level and walls are vertical and square.
2. Shower ttings should be positioned such that water discharges down the centre line
of a bath or across the opening of a shower cubicle door.
3. Ensure water is not directed at the shower door or side panels. This could result in water
spraying outside of the enclosure.
4. Ensure the door opening is positioned correctly and is adequate for all users.
5. Ensure there is a complete silicone seal between the tray and nished wall.
6. Ensure the door is undamaged and no parts are missing.
General
1. Read all of these instructions and retain this guide for later use.
2. Pass on this guide in the event of change of ownership of the installation site.
3. Follow all warnings, cautions and instructions contained in this guide.
4. Remove all protective tape from the enclosure before installation.
5. Excessive ow rates may lead to overowing and leaking.
6. Water Spray may extend beyond the entrance of walk-in enclosures and we recommend
tiling of the adjacent area.
7. We recommend a drainage test is carried out to ensure the waste is adequate for the
ow delivered.
8. Doors that open outwards may drip water onto oor, ensure the oor covering will not
be affected by water.
9. Walk ins and divider panels are designed to minimise water escaping outside the
enclosure but by their very nature are not fully water tight.

4
1245548-W2-A
6.0 mm
TOOLS REQUIRED
Domestic ü
Light Commercial ü
Heavy Commercial û
Healthcare û
RECOMMENDED USAGE
GUARANTEE
When Fitting the Enclosure
1. The wall channels must be installed onto a tiled or waterproof nished at and even wall
surface. Failure to do so will result in an unsatisfactory seal, which may cause property
damage.
2. We recommend our enclosures are tted onto shower trays.
Warning! The use of grout/tile cleaners, scale removers, abrasive scourers, drain
unblockers and other powerful detergents may lead to damage of metallic, plated and
plastic surfaces, including the tray and shower waste.
Use of the Enclosure
1. High water pressure and ow may lead to excessive splashing causing water to escape
outside of the enclosure.
2. In certain circumstances such as cleaning, water sprayed directly at the seals may
escape outside of the enclosure.
7. Ensure the size of door/panel is suitable for the installation. Tempered safety glass
cannot be cut.
8. Ensure nothing can impact the door or glass panels during operation.
For domestic installations, your enclosure has the benet of our lifetime guarantee which
starts from date of purchase.
For non-domestic installations, we guarantee the product against any defect in materials
or workmanship for a period of one year from the date of purchase.
For terms and conditions refer to the back cover of this guide.
A ICOlf.ER.COMPANY

51245548-W2-A
PACK CONTENTS
Tick the appropriate boxes to familiarise yourself with the part names and to conrm
that all of the parts are included.
Documentation
q1 x Guarantee Registration Document
x5
A
x3
B
x1
C
x5
2.5mm
3mm
x4
1700 Top Cap
1400 Top Cap
Filler Cap
Allen Grub Screws
RH Lintel Glass
Mounting Block LH Lintel Glass
Mounting Block
Lintel
Lintel Wall
Mount
Mounting Block
Corner
Gasket
Curved Glass
Panel
Wall Channel
Slotted
Grub Screw

6
1245548-W2-A
INSTALLATION
x3
x3
6mm
x3
x3
A
FITTING INSTRUCTIONS
The tray should be fitted and the walls tiled
before installation of the enclosure.
Mark the position of the wall channel
from the wall tiles on the back wall.
STEP
1
STEP
2
STEP
4
STEP
3
Back edge
of wall
channel
Wall channel
MUST be
vertical on
the front face.
Fit the curved panel wall channel to the wall.
Place the glass mounting block into the tray.
IMPORTANT
Do not remove the adhesive backing from the
underside of the mounting block at this stage.
Carefully lift the glass into place. The jamb fits
onto the wall channel and the bottom corner of the
glass fits into the mounting block (see Step 5).
NOTE:
LH VERSION
SHOWN.
RH FITTING
MIRRORS THE
INSTALLATION
SHOWN.
4
CFI270G
745mm (1400 tray)
640mm (1700 tray)
(adjust the dimension
if other than
10mm tile thickness)

71245548-W2-A
5
CFI270G
Carefully slide the jamb onto the wall channel.
STEP
5
STEP
7
STEP
6
Place the corner of the glass into the
mounting block.
Adjust the glass until it is vertical and equally
spaced around the lip of the tray.
Carefully remove the curved panel from the tray.
Remove the mounting block.
Remove the backing paper from the mounting block.
Wall channel
Jamb
Mark the position of the mounting block on the tray.
Fit the mounting block to the marks on the tray.
Place a blob of sealant into the mounting block.
Backing
paper
=
A ICOHLER. COMPANY

8
1245548-W2-A
CFI270G 6
Carefully lift the curved panel back into place and
check that the glass is vertical and equally spaced
around the lip of the tray.
STEP
9
STEP
11
STEP
10
Drill 3 x 3mm holes through the jamb into the
wall channel.
STEP
8
Secure the jamb to wall channel with
3 x screw B.
B
Mark the fixing point for the lintel on the wall
at the height of the top of the glass.
Loosely fit the parts of the lintel together.
Note: the lintel end with a straight section
goes towards the wall.
984mm (1400 tray)
1240mm (1700 tray)
(adjust the dimension if other
than 10mm tile thickness)
A ICOlf.ER.COMPANY
' ,
-- ,
~-

91245548-W2-A
7
CFI270G
Place the lintel on top of the glass.
STEP
12
STEP
14
STEP
13
Fit the corner glass gasket to the glass then place
the lintel glass mounting block on top.
Remove the lintel. Take the wall mount off the lintel
and place on the wall as marked.
Fit the lintel to the wall mount.
Ensure the glass is vertical
and and the lintel is horizontal.
When the lintel is horizontal and the inner edge of the
wall mount is against the mark, draw around the
wall mount.
Mark the position of the two
fixing holes on the wall
A
Fit the mounting block to the glass and lock
in place by turning screw ‘A’.
A
Drill 2 x 6mm holes. Fit plugs.
Secure the
wall mount with
2 x screw A.
A ICOHLER. COMPANY

10
1245548-W2-A
CFI270G 8
STEP
15
If any adjustment is required, move the lintel
in or out until the glass is vertical.
Ensure the glass is vertical
and and the lintel is horizontal.
When the glass and lintel are in the correct position
tighten the grub screws at both ends.
C
Fit the top caps.
STEP
17
Seal between the wall channel and the wall.
STEP
16
Fit the cover strip.
24hrs
Do not use the enclosure for at least 24 hours.

11 1245548-W2-A
MAINTENANCE
General Maintenance
Providing the shower enclosure has been correctly installed and is operated in
accordance with the instructions contained in this guide, difculties should not arise.
If any maintenance is required then it must be carried out by a competent tradesperson
to whom the maintenance instructions are provided.
Before replacing any parts ensure the underlying cause of the malfunction has been
resolved.
Chrome Parts
Use only cleansers expressly specied for chrome!
Care
To preserve the beauty of your shower enclosure for many years, please observe
the following care instructions:
Rinse glass and frame with clear water after showering. Remove water droplets
with a squeegee. Do not rub dry! To clean your shower hygienically and easily, we
recommend the use of a biodegradable cleanser.
Regular cleansing with a biodegradable cleanser prevents stubborn stains and
ensures a clean and hygienic surface for many years. Do not use scouring or caustic
cleansers under any circumstances! These can damage the surface of the frame,
glass and decorative parts as well as the plastic parts.
Cleaning
Warning! The use of grout/tile cleaners, scale removers, abrasive scourers, drain
unblockers and other powerful detergents may lead to damage of metallic, plated
and plastic surfaces, including the tray and shower waste.
Avoid the use of ‘spray and leave’ cleaners. Any cleaner used should have a pH
level between 4 and 8 and immediately wiped dry using a soft cloth.
KOHLER Glass Cleaner
For occasional cleaning of glass treated with KOHLER Glass
Protector or for more regular maintenance of untreated
surfaces, we recommend using KOHLER Glass Cleaner.
The cleaner cleans and polishes without smearing or
streaking and rejuvenates the Glass Protector.
A ICOHLER. COMPANY

12
1245548-W2-A
9
CFI270G
Spare Parts
SPARE PARTS
207252 pp (1400) 200515 pp
\ ' 206792
207251 pp (1700) I
200583
207259 pp~ \!
306581
'
,I. '
_ JLJ j'
307066 (307066+200583 = ASS'Y 307064) (1400)
307065 (307065+200583 = ASS'Y 307063) (1700)
207348
200464 pp
m:~~ ~~ \~iiwi
400821 LH (1700)
400822 RH (1700)
To ensure correct replacement parts are sent be readyto quote
the
six digit code from this drawing e.g. 304781
PP aftera part means
it is contained in the parts pa ck
LH unitshown, RH is mirror image
'
l
16791
204746 PP
I
307093 pp
207285 pp LY 200004 pp
206754 PP
307075 pp
307094 LH PP / ~04746 pp l • ?~,o\-
307095 RH PP '-...... J / ~\. s\fJf:.
"d o~-r;, ,o
208074 (1400)
207121 (1700)
304907 PP
204757 pp
EX 76 (Mira 1 400 1700)-4
f
2004 ~.:91 pp
j
r;:= 207285 pp
ir- 200004 pp
,,
' ,,
' ,,
' ,,
' ,,
' ,,
' ,,
' ,,
' ,,
' ,,
' ,,
' ,,
,,
,,.
,,
,,
,,
,,
•:
:.R 207285 pp
• ' [ 204 746 pp
: : r 200 004 pp
: : ~ 04787PP
'•
.,
,,
:,
,,
,,
I I 30488 7
,,
,,
,,
,,
~,!.
307078
\ 307077 (307078+200583 = ASS'Y 307079)
207348

13 1245548-W2-A
NOTES

14
1245548-W2-A
NOTES

15 1245548-W2-A
DECLARATION OF PERFORMANCE
DECLARATION OF PERFORMANCE
Signed for and on behalf of Kohler Mira Ltd.
Signature: _______________________
Name: Andrew Baines Position: NPD Director
Place: Cheltenham, UK Date: 1
st September 2014
Doc. No.: CE 0099 Issue: 1.
Brand name: Mira
Product name: Leap Shower Enclosures
Product Range: Leap Pivot Door, Leap Bi-Fold Door
Leap Sliding Door, Leap Side Panel
Leap Quadrant Enclosure Leap Pentagon Enclosure,
Leap Walk in Enclosure, Leap Double Door Slider
Leap Extended Sliding Door
Product type: Domestic Shower Enclosure
Manufacturer: Kohler Mira Ltd
Cromwell Road, Cheltenham
Gloucestershire GL52 5EP
United Kingdom.
Directives: EU 305/2011 Construction Products Regulations
System of System 4:
assessment: Type testing / Factory production Control
Standards: EN 14428:2004 +A1:2008.
Shower enclosures – Functional requirements and test methods.
Essential Characteristics
Performance
Harmonised technical specification
IR-CA-DA
Compliant
EN 14428:2004 +A1:2008
The performance of the products described above, are in conformity with the relevant community
harmonisation legislation.
This declaration of performance is issued under the sole responsibility of Kohler Mira Ltd.
14
A KOHLER. COMPANY
CE

16
1245548-W2-A © Kohler Co. September 2014
To Contact Us: UK
CUSTOMER SERVICE
E-mail: www.mirashowers.co.uk/
contactus
0844 571 5000
Fax: [phone]
Helpdesk Service
Our Customer Services Team is comprehensively
trained and can offer help and advice, spare
parts, accessories or a service visit.
We will need you to have your model name,
model number and date of purchase.
Mira Showers Website (www.mirashowers.
co.uk)
From our website you can register your
guarantee, download additional user guides,
diagnose faults, purchase our full range of
accessories and popular spares, refer to our
FAQ’s and request a service visit.
Spares and Accessories
We hold the largest stocks of genuine Mira spares
and accessories.
Contact us for a price and to purchase spares
or accessories (Only available in the United
Kingdom).
Service / Repairs
No one knows our products better than our
nationwide team of Service Technicians. We can
carry out service or repair work to your product
both during and after the guarantee period (Only
available in the United Kingdom and the Republic
of Ireland).
Ask about our fi xed price service repairs.
Guarantee
Your enclosure has the benefit of our lifetime guarantee
which starts from the date of purchase. This guarantee
only applies in the United Kingdon and the Republic of
Ireland.
To activate this guarantee, you must return your completed
registration card with a copy of proof of purchase from
an approved Mira retailer within 30 days of purchase.
This guarantee is in addition to your statutory rights
and is subject to conditions (see registration card).
What to do if something goes wrong
If your product does not function correctly when you fi rst
use it, contact your installer to check that it is installed in
accordance with the instructions in this manual.
If this does not resolve the issue, contact our Customer
Services Team who will offer you or your installer help
and advice.
Mira is a registered trade mark of Kohler Mira Limited.
The company reserves the right to alter product
specifications without notice.
DAP 16.06.2013
CE mark label to be on all Leap range of shower enclosures.
14
Kohler Mira Ltd, Cromwell Road, Cheltenham, Gloucestershire
GL52 5EP, UK.
Essential Characteristics Performance Specification
IR-CA-DA
Compliant
EN 14428:2004 +A1:2008
Mira
Leap Range of Domestic Shower Enclosures.
Declaration of Performance: CE 0099
Pivot Door, Bi-Fold Door, Sliding Door, Side Panel,
Quadrant Enclosure, Pentagon Enclosure, Walk in
Enclosure, Double Door Slider, Extended Sliding Door.
5013181 080216
A KOHLER.COMPANY
•
•
.
•
CE
I
I I 7 7
7

Check out our full range of Shower Enclosures
Quadrant Shower Enclosures
Corner Entry Shower Enclosures
Walk in Shower Enclosures
Sliding Shower Doors
Bifold Shower Doors
Pivot Shower Doors
Hinged Shower Doors
Shower Screens
From Top Brands
Coram Shower Enclosures
Mira Shower Enclosures
Hydrolux Shower Enclosures
Diamond Shower Enclosures
With quality shower trays to match your enclosure
Square Shower Trays
Rectangular Shower Trays
Quadrant Shower Trays
Coram Shower Trays
Mira Flight Shower Trays