Mircom MPS-800MP Series User manual

www.mircomgroup.com LT-6168 Rev. 0 Oct 2021
MPS-800MP(U) Series
Fire Alarm Manual Station
1
Mircom’s MPS-800MP(U) Series Fire Alarm Manual Stations
provide manual fire alarm activation.
This guide covers these models:
MPS-810MP Single Stage, Dual Action, MP Addressable Manual
Station
MPS-810MPU Single Stage, Dual Action, MP Addressable
Manual Station (US)
MPS-802MP Two Stage, Dual Action, MP Addressable Manual
Station
MPS-822MP Two Stage, Dual Action, MP Addressable Manual
Station with additional door contacts
Specifications & Dimensions
Compatible with FX-400 series and FleX-Net™ FX-4000 Fire
Alarm Control Panels
Electrical Rating:
Nominal Operating Voltage: 15-30 VDC
Maximum alarm current: 3.3 mA
Standby current: 2 mA
Electrical Rating for MPS-822MP maglock terminal:
1A at 30VDC
Dimensions:
139 mm H x 104 mm W x 34 mm D
(5 1/2” H x 4 1/8” W x 1 3/8” D)
Install the manual station
Contents of kit
MPS-810MP(U): 2 mounting screws, 2 reset keys (black)
MPS-802MP and MPS-822MP: 2 mounting screws, 2 reset keys
(black), 2 stage two keys
A. Open
1. Insert the reset key into the reset keyhole and turn it.
2. Pull the cover open.
Figure 1 Front of manual station
Figure 2 Opening the station
Notes
• Environment: Indoor, dry
• Do not change factory applied finishes.
• Wire as shown so that supervision of connections is
maintained.
• Maximum wire size: 14 AWG
• ADA compliant.
• To be installed per ADA 4.27.1 to 4.27.4 inclusive.
• Wiring must be in accordance with CSA C22.1, Canadian
Electrical Code, Part I, Safety Standard for Electrical
Installations, Section 32 and CAN/ULC-S524, Standard for
Installation of Fire Alarm Systems.
• All manual fire alarm stations shall be installed as per the
specific requirements outlined in the UL/ULC codes, as well
as all other applicable national or local codes. Final
acceptance is subject to the local authority having
jurisdiction.
RESET KEYHOLE
STAGE TWO
KEYHOLE (MPS-802MP
A
ND MPS-822MP)
PUSH BAR
PULL HANDLE
LED FLASHES RED
WHEN POLLING AND IS
STEADY RED IN ALARM
COVER
MOUNTING
PLATE
Canada
25 Interchange Way
Vaughan, ON L4K 5W3
Tel: [phone]
U.S.A
4575 Witmer Industrial Estates
Niagara Falls, NY 14305
Tel: [phone]

MPS-800MP(U) Series
Fire Alarm Manual Station
www.mircomgroup.com LT-6168 Rev. 0 Oct 2021
2
B. Wire
Note: The maximum wire size is 14 AWG.
1. Strip wires to 10 mm (25/64”) maximum.
2. Push the wire into the terminal.
Note: The terminals have a push-in lock. To remove the wire,
push the terminal in with the screwdriver and pull out the
wire at the same time. see Figure 3.
Figure 3 Removing the wire
3. Wire as shown in Figure 4.
Figure 4 Wiring
C. Mount
Flush mount indoor: Single-gang electrical box.
Surface mount indoor: BB-800 backbox with or without STI-1230
(Deep Cover without Gasket)
Note: Mount the manual station with the Mircom logo on the
bottom.
Figure 5 Back of manual station
D. Set the addressable module
Follow the instructions in LT-6146, the MIX-4090 Device
Programmer Installation Manual, available on
http://www.mircom.com.
The factory default address is 255.
The connector for the device programmer is inside the unit above
the addressable module, as shown in Figure 6.
Figure 6 Connector for device programmer
Using the manual station
Activate the alarm
1. Push in the push bar.
2. Pull down the pull handle.
A qualified person must reset the station by opening it with the
reset key. See Resetting the manual station below.
Activate the stage two alarm (MPS-802MP and
MPS-822MP)
• Insert the stage two key into the stage two keyhole, and then
turn the key.
The stage two alarm activates immediately.
Note: The stage two alarm will activate automatically a certain
amount of time after the handle has been pulled if no
action is taken. This time is set in the Fire Alarm Control
Panel.
Reset the manual station
Note: Resetting the station does not cancel the alarm at the
panel.
1. Insert the reset key into the reset keyhole and turn it.
2. Pull the cover open. The switch is now reset.
3. Close and lock the station with the reset key.
4. Reset the Fire Alarm Control Panel to reset the alarm.
TO REMOVE WIRE, PLACE
A SMALL FLATHEAD
SCREWDRIVER INTO THE
GROOVE AND PUSH IN.
AT THE SAME TIME, PULL
THE WIRE OUT OF THE
TERMINAL.
TO NEXT STATION OR
LEAVE IT EMPTY
FROM
PREVIOUS
STATION
TO MAGLOCK
(MPS-822MP)
NO
C
+
+
NC
í
í
MOUNTING
HOLES
CONNECTOR
FOR DEVICE
PROGRAMMER