Mircom MPS-800MP Series User manual

NOT TO BE USED FOR INSTALLATION PURPOSES.
THIS INFORMATION IS FOR MARKETING PURPOSES ONLY AND
NOT INTENDED TO DESCRIBE THE PRODUCTS TECHNICALLY. 5964
CATALOG NUMBER
FIRE ALARM ADDRESSABLE MANUAL PULL STATIONS MPS-800MP(U) SERIES
Description
Mircom’s MPS-800MP(U) Series Fire Alarm Manual Pull
Stations provide manual fire alarm activation. The new
MPS-800 Series uses raised symbols and icons instead of
printed text that makes them universally recognized.
These addressable pull stations are available as single or two
stage dual action devices. Compatible with FX-400 Series and
Flex-Net FX-4000 Fire Alarm Panels.
The MPS-800MP(U) manual stations are constructed of
high quality polycarbonate resin thermoplastic “LEXAN” that
supports high temperatures without deforming.
The MPS-800MP(U) addressable pull stations are accessible
from the front for wiring while mounted making it easy to install.
These pull stations can be mounted on a single gang backbox
and the mounting holes permit easy alignment to the wall.
The suffix “U” indicates USA version.
All manual fire alarm stations shall be installed as per the
specific requirements outlined in the UL/ULC codes, as well
as all other applicable national or local codes.
Addressing is done using the MIX-4090 Device Programmer.
For setting the address on this device, disconnect it from the
loop, or ensure that the loop to which is connected is both
disconnected from the panel and shorted across the SCL+ and
SLC- inputs at the device. Failing to take either of these steps
may change the address programming of previously configured
sensors on the loop.
Features
• Completely made of LEXAN material
• Closed-fist operation (ADA – Americans with Disability Act)
• No printed text on the devices, symbols and icons are
used instead
• Symbols are raised to be easily recognized by touch
• Compatible with FX-400 Series and Flex-Net FX-4000 Fire
Alarm Panels
• Easy installation
• Accessible from the front for wiring while mounted
• Mounts on a single gang backbox
• Temperature range from 0ºC to 49ºC
• UL and ULC listed
• Device comes with a reset key
• Indoor use only
• Alarm LED is viewable from the front - Useful for trouble
shooting
MPS-810MP(U)
1 Stage
MPS-802MP
2 Stage
Operation
Activating the Alarm
• Push in the push bar
• Pull down the pull handle
Activating the stage two alarm (MPS-802MP and
MPS-822MP)
• Insert the stage two key into the stage two keyhole, and
then turn the key.
• The stage two alarm activates immediately.
Resetting the manual station
• Insert the key into the reset keyhole and turn it.
• Pull the cover open. The switch is now reset.
• Close and lock the stations with the reset key.
• Reset the Fire Alarm Control Panel to reset the alarm
Note: Resetting the station does not cancel the alarm at the
panel

CAT. 5964
Rev. 0
Ordering Information
Model Description
MPS-810MP MP 1 Stage Addressable Double Action Pull Station, ULC
MPS-810MPU MP 1 Stage Addressable Double Action Pull Station, UL
MPS-802MP MP 2 Stage Addressable Pull Station, ULC
MPS-822MP MP Maglock 2 Stage Double Action Pull Station, ULC
MIX-4090 4000 Series Address Programmer
BB-800 Surface Backbox for 800 Series Manual Station
THIS INFORMATION IS FOR MARKETING PURPOSES ONLY AND
NOT INTENDED TO DESCRIBE THE PRODUCTS TECHNICALLY.
For complete and accurate technical information relating to performance, installation, testing
and certification, refer to technical literature. This document contains intellectual property of
Mircom. The information is subject to change by Mircom without notice. Mircom does not
represent or warrant correctness or completeness. All rights reserved. All other trademarks
and registered trademarks are properties of their respective owners.
Canada
25 Interchange Way Vaughan, ON L4K 5W3
Telephone: [phone] | Fax: [phone]
U.S.A.
4575 Witmer Industrial Estates Niagara Falls, NY 14305
Toll Free: [phone] | Fax Toll Free: [phone]
www.mircom.com
Specifications
Dimensions Manual Pull Station: 5 ½” H x 4 1/8” W x 1 3/8” D
Nominal Operating Voltage: 15-30 VDC
Maximum alarm Current: 3.3 mA
Standby current: 2 mA
Electrical rating for MPS-802MP Maglok terminal: 1 Amp @ 30 VDC
Wiring Diagram Mounting Diagram
• Flush mount indoor: Single-gang electrical box
• Surface mount indoor: BB-800 backbox
NO
C
+
+
NC
TO NEXT STATION OR
LEAVE IT EMPTY
FROM
PREVIOUS
STATION
TO MAGLOCK
(MPS-822MP)
MOUNTING
HOLES
NO
C
+
+
NC
TO NEXT STATION OR
LEAVE IT EMPTY
FROM
PREVIOUS
STATION
TO MAGLOCK
(MPS-822MP)
MOUNTING
HOLES