Mistral 6220-0 Parts list manual

Expressaire Exhaust Fan
6220-0
Installation Instructions / Warranty Card
Important:
Please retain this warranty

Installation Instructions
6220-0
All fans should be installed by a suitably qualified person in accordance with AS/NZ3000.2000
and relevant building codes. Disconnect supply before making any electrical connections.
For best results provision should be made for return air to enter the room on the opposite
side. In some instances a return air grille/vent may be required.
Installation:
1. This card can be used as a template for making appropriate fan mounting hole size.
2. Cut hole of the required diameter (290mm dia.) in the desired position in the ceiling.
3. Attach earthed plug base on joist as near as possible to mounting hole.
4. Remove fan blade by unscrewing central knob anticlockwise, refer fig. 1.
5. Remove screw hole plugs from duct mounting arm, refer fig. 1.
6. Support fan whilst connecting 3-pin plug.
7. Insert fan into opening in the ceiling. Push the 3 brackets back through the duct, refer fig.2. Pull
screws down and tighten until duct is firmly fixed to the ceiling. Plug must be accessible after
installation.
8. Replace fan blade making sure that shaft cross bar engages fan blade hub correctly.
9. Insert screw cover plugs over 3 mounting screws.
10. Ducting must be no closer than 250mm to chimney flue or other similar exhaust flue (refer fig.3).
11. If the supply cord is damaged it must be replaced by the manufacturer or its service agent, or a
similarly qualified person, in order to avoid a hazard.
WARNING:
The appliance is not intended for use by children or infirm persons without supervision. Children
should be supervised to ensure they do not play with the appliance. Appliance is intended to be
mounted on external wall only.
Cleaning (Ensure fan is unplugged or switched off at mains):
1. Remove fan blade by unscrewing central knob.
2. Wash fan blade in warm soapy water, rinse clean and dry fan blade.
3. Fan duct may be wiped down with moist soapy cloth.
4. Replace fan blade.
Use this template to mark mounting hole for the fan. Use a nail or similar object
to anchor the template at the centre hole, then insert a pencil through the
template at the 290mm marking and scribe a circle.
TEMPLATE
290mm
diameter
Centre Hole
Ceiling
Push in plug Figure 1
Figure 3: Ducting Arrangements
Fire
Fan & Duct
250mm
min Exhaust Flue
DO NOT INSTALL WITHIN 120cm OF STOVE
Figure 2
Push
Pull screw down
Tighten
Fan blades are removed
by unscrewing central
knob anti-clockwise

Products of Gerard Industries Pty Ltd ABN27007873 529
12 Park Terrace, Bowden, SouthAustralia 5007
Telephone [phone]Facsimile [phone]
Internet clipsal.com
E-Mail[email protected]
F1717
Replacement Warranty
The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the
product which the consumer has under the Trade Practices Act and similar State and Territory laws.
The original purchaser of this Mistral Exhaust Fan is provided with the following warranty, subject to the
following conditions. Gerard Industries Pty Ltd warrant this product for a period of 3 years from the
date of purchase for all parts defective in workmanship or materials. All defective parts will be
replaced free of charge. The following exclusions do not preclude the purchaser from those statutory
rights consumers have under the Trade Practices Act or similar State and Territory laws.
Replacement Warranty Conditions
1. This warranty is only valid for appliances installed according to the manufacturer’s instructions.
2. This appliance must not be modified or changed in any way.
3. All wiring must be carried out by a licensed electrician or similarly qualified person and must be
connected to the voltage requirements as specified on the ratings label.
4. The manufacturer does not accept liability for any direct or consequential damage, loss or other
expense arising from misuse or incorrect installation and operation of the appliance.
5. Warranty will only be given on appliances where proof of purchase date is provided, e.g. original
invoice or copy.
6. As a record of your purchase, please fill out the following details and file this information with your
purchase invoice.
Mistral Model Number
Serial Number
Purchased From
Date of Purchase
© Copyright 2002
WA
Perth [phone]
TAS
Hobart [phone]
Launceston [phone]
NT
Darwin [phone]
NZ
Nth Island [phone]
Sth Island [phone]
For Warranty Service please call your nearest Clipsal Office.
NSW
Sydney [phone]
Albury [phone]
VIC
Melbourne [phone]
Country Areas 1800 653 893
QLD
Brisbane [phone]
Townsville [phone]
SA
Adelaide [phone]