Mistral 6250-0 Parts list manual

Ceiling Exhaust Fan
6250-0
Installation Instructions/Warranty Card
Important: Please retain this warranty.

6250-0 Ceiling Exhaust Fan Installation Instructions
© Clipsal Australia Pty Ltd
Installation Instructions
6250-0
All fans should be installed by a suitably qualified person in accordance with
AS/NZ3000 and relevant building codes. Disconnect supply before making any
electrical connections.
For best results provision should be made for return air to enter the room on the
opposite side. In some instances a return air grille/vent may be required.
Installation:
This card can be used as a template for making appropriate fan mounting hole size.1.
Cut hole of the required diameter (in the desired position) in the ceiling.2.
Attach Earthed plug base on joist as near as possible to the mounting hole.3.
Remove grille by pulling from outside edge.4.
Support fan whilst connecting 3-pin plug to plug base.5.
Insert fan into opening in the ceiling. Push the 3 brackets back through the duct6.
(see diagram). Pull screws down and tighten until duct is firmly fixed to the ceiling.
Caution:
Fan must be mounted at least 120cm above any hotplate and must have at least1.
50cm of clear space above the fan blades.
Do not install in canopies.2.
If ducting is required, its diameter over the full length shall be no smaller than the3.
diameter of the fan blades and no longer than one metre. Restrictions of any kind
will affect the performance of the fan.
Warning:
The appliance is not intended for use by young children or infirm persons unless they
have been adequately supervised by a responsible person to ensure that they can use
the appliance safely.Young children should be supervised to ensure they do not play
with the appliance.
Cleaning (ensure fan is unplugged or switched off at mains):
Remove grille by pulling the outside edge of grille down.1.
Wash grille in hot soapy water and wipe fan blades.2.
Replace grille by pushing grille into fan opening. Fan blade may be removed by3.
undoing screw in the centre of the fan blade.
Template:
Use this template to mark mounting hole for the fan. Use a nail or similar object to
anchor the template at the centre hole, then insert a pencil through the template at the
295mm marking and scribe a circle.
Centre Hole

© Clipsal Australia Pty Ltd
6250-0 Ceiling Exhaust Fan Installation Instructions
295mm
6250-0
Ceiling
Push
Push Push
Pull screw down
Tighten

F1724/02
CLIPCOM 19006 April 2009
Clipsal Australia Pty Ltd reserves the right to change specifications,
modify designs and discontinue items without incurring obligation
and whilst every effort is made to ensure that descriptions,
specifications and other information in this catalogue are correct, no
warranty is given in respect thereof and the company shall not be
liable for any error therein.
© Clipsal Australia Pty Ltd. The identified trademarks and copyrights
are the property of Clipsal Australia Pty Ltd unless otherwise noted.
Product of Clipsal Australia Pty Ltd
A member of Schneider Electric
Contact us: clipsal.com/feedback
National Customer Care Enquiries:
Tel 1300 2025 25
Fax 1300 2025 56
clipsal.com
Warranty
The benefits conferred by this warranty are in addition to all other rights and remedies in
respect of the product which the consumer has under the Trade Practices Act and similar
State and Territory Laws.
The original purchaser of this Mistral Exhaust Fan is provided with the following warranty,
subject to the following conditions. Clipsal Australia Pty Ltd warrant this product for a period of
three (3) years from the date of purchase for all parts defective in workmanship or materials.
All defective parts will be replaced free of charge. The following exclusions do not preclude
the purchaser from those statutory rights consumers have under the Trade Practices Act or
similar State and Territory Laws.
Replacement Warranty Conditions
This warranty is only valid for appliances installed according to the1.
manufacturer’s instructions.
This appliance must not be modified or changed in any way.2.
All wiring must be carried out by a licensed electrician or similarly qualified person and3.
must be connected to the voltage requirements as specified on the ratings label.
The manufacturer does not accept liability for any direct or consequential damage, loss or4.
other expense arising from misuse or incorrect installation and operation of the appliance.
Warranty will only be given on appliances where proof of purchase date is provided, e.g.5.
original invoice or copy.
As a record of your purchase, please fill out the following details and file this information6.
with your purchase invoice.
Mistral model number:
Serial number:
Purchased from:
Date of purchase: